• 한국터널지하공간학회 논문집
• /
• 제17권5호
• /
• pp.533-551
• /
• 2015

암석은 인공적인 재료(금속, 유리)에 비해 불균질하고 이방성을 가지고 있기 때문에 워터젯 절삭시 매우 복잡하게 파쇄되는 특성을 가진다. 워터젯 절삭시 암석특성에 따라 절삭성능이 결정되므로 물성에 대한 영향을 파악하는 것은 매우 중요하다. 워터젯 절삭효율에 영향을 미치는 물성은 선행문헌의 실험조건(수압, 연마재 투입량, 이격거리 등) 및 암종에 따라 다양하게 제시되고 있다. 본 연구에서는 워터젯 시스템을 이용한 암석절삭에 있어서 물성영향에 대해 문헌연구를 실시하고 중요 물성을 분석하였다. 선행문헌 연구를 통해 암석의 공극율, 일축압축강도, 경도가 워터젯 암석 절삭에 있어서 중요한 물성으로 도출되었다. 분석결과는 향후 워터젯 절삭 기술을 이용한 터널공사시, 암반특성에 따른 굴착효율을 예측하기 위한 기초지식을 제공할 수 있을 것이다.

• 터널과지하공간
• /
• 제15권6호
• /
• pp.411-424
• /
• 2005

풍화작용은 심부에서 생성된 암석이 지표에서 파괴되고 변질되어 현재의 환경조건과 평형을 이루는 산물을 형성하는 과정이다. 본 연구에서는 국내에서 가장 분포면적이 넓은 화강암질암의 풍화단계별 시료를 채취하여 편광현미경관찰, X-선 회절분석, 전자현미경관찰, 화학분석, 물성시험등을 수행하였다. 실험결과에 의거하여 풍화에 의해 형성되는 2차광물, 특히 점토광물의 형성과정을 확인하였고, 풍화에 따른 암석의 공학적인 성질변화와 물성저하의 메카니즘을 규명하였다.

• 터널과지하공간
• /
• 제6권4호
• /
• pp.316-325
• /
• 1996

A new accelerated neural network adopting modified sigmoid function was developed and applied to estimate engineering properties of rock from insufficient geological data. Developed network was tested on the well-known XOR and character recognition problems to verify the validity of the algorithms. Both learning speed and recognition rate were improved. Test learn on the Lee and Sterling's problems showed that learning time was reduced from tens of hours to a few minutes, while the output pattern was almost the same as other studies. Application to the various case studies showed exact coincidence with original data or measured results.

• 지질공학
• /
• 제26권4호
• /
• pp.593-600
• /
• 2016

본 연구에서는 국내의 107개 터널 설계 과정에서 수행한 현장 및 실내시험 자료 4,280개를 이용하여 암반 및 무결암의 역학적 특성을 암종 및 강도별로 분석하였다. 분석된 물리 및 역학적 특성은 단위중량, 점착력, 내부마찰각, 변형계수, 탄성계수, 포아송비, 일축압축강도, 인장강도, 투수계수, 비중이다. 평균값의 분석 결과에 의하면 편마암은 비중, 화강암은 투수계수, 퇴적암은 단위중량과 점착력, 내부마찰각, 화산암은 변형계수와 탄성계수, 일축압축강도, 인장강도, 변성암은 포아송비에서 가장 높은 값을 보인다. 역학적 특성의 분포 범위는 암종 및 강도를 고려한 분석에도 불구하고 넓게 분포하며, 이는 암반의 불균질성과 이방성에 기인하는 것으로 판단된다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1993년도 봄 학술회 논문집
• /
• pp.33-40
• /
• 1993

The Bieniawski's geomechanics classification system(1984) is widely employed as a tool of engineering evaluation of rock masses for tunnel design. Since the siz parameters adoped in the system are believed to control the engineering behavior of rock mass under an external load, no question may be raised to the conceptional idea immanent in the system. However, the rating grade for each individual parameter given in the system may be properly measured since an engineering property of rock mass is not stepwise changed but continuously changed. In order to get the proper rating grade based upon the continuously changed properties in each parameter, several equations presented in this paper are obtained through regration analyses with the grades and median values of properties givne in the system. A FORTRAN computer program given in the paper could provide not only RMR value but also rock mass properties (E, c, o, v, etc.) using the empirical equations.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 기초기술학술발표회
• /
• pp.31-42
• /
• 2002

The Design criteria are different from one another due to the different engineering properties of rock in the every nation. Most of the test results of the rock-socketed piers were loaded two times of the design load capacities because they would be used in the foundation of the bridge or the building. So we have much difficulties in study of the load capacities of the rock-socketed piers by the test result in Korea. When we design the rock-socket piers, every designer uses the different formula, and makes different results. Recently the demand of the large bridges and the huge buildings has been increased. The adequate design criterion of the rock-socketed pier is urgently needed to design them reasonable. In this paper we analyzed the various design criteria and proposed the adequate design criterion which is based on the test results of the rock-socked piers in Korea.

• 한국안전학회지
• /
• 제9권4호
• /
• pp.103-111
• /
• 1994

Recently, rock slope in large scale is often accompanied with the construction of mountain roads and power plants. Rock in nature has a number of discontinuities such as bedding plane, joints, fracture zones and others. In order to improve rock slope stability, it is necessary to research shear properties of rock joint. In this paper shear properties of rock joint were studied by tilting test. Relations between properties of roughness and shear behavior of rock joint are investigated experimentally. The roughness are examined by compared with shear strength. Consequently, it becomes clear that the engineering properties and failure state modes of slope is different by JRC, and the peak friction angle is different by percent of filling.

• 터널과지하공간
• /
• 제4권2호
• /
• pp.102-118
• /
• 1994

Thermomechanical analysis is conducted on the radioactive repository in deep rock mass considering the in-situ stress, excavation and thermal loading of a radioactive waste. Thermomechanical properties of a discontinuous rock mass are estimated by a theoretical method so called sequential analysis. Using the estimated properties as input for finite element analysis, the influence on temperature distribution and thermal stress is analyzed within the scope of 2-dimensional steady state and transient heat transfer and coupled thermal elastic plastic behaviour. Granitic rock mass is taken for this analysis. The analysis is done for two different rock mass conditions, i.e. continuous-homogeneous and highly jointed conditions, for the purpose of comparison. In the case of steady state, the extent of disturbed zone around the storage tunnel due to the heat production of the spent-fuel canister varies depending on the thermomechanical properties of the rock mass. In the case of transient analyses, the response of the jointed rock mass to the thermal loading after radioactive waste disposal varies significantly with time, resulting in dramatic changes in the both size and location of disturbed zone.

• Geomechanics and Engineering
• /
• 제30권1호
• /
• pp.93-105
• /
• 2022

With the exploitation of natural resources in China, underground resource extraction and underground space development, as well as other engineering activities are increasing, resulting in the creation of many defective rocks. In this paper, uniaxial compression tests were performed on rocks with double holes and fractures at different angles using particle flow code (PFC2D) numerical simulations and laboratory experiments. The failure behavior and mechanical properties of rock samples with holes and fractures at different angles were analyzed. The failure modes of rock with defects at different angles were identified. The fracture propagation and stress evolution characteristics of rock with fractures at different angles were determined. The results reveal that compared to intact rocks, the peak stress, elastic modulus, peak strain, initiation stress, and damage stress of fractured rocks with different fracture angles around holes are lower. As the fracture angle increases, the gap in mechanical properties between the defective rock and the intact rock gradually decreased. In the force chain diagram, the compressive stress concentration range of the combined defect of cracks and holes starts to decrease, and the model is gradually destroyed as the tensile stress range gradually increases. When the peak stress is reached, the acoustic emission energy is highest and the rock undergoes brittle damage. Through a comparative study using laboratory tests, the results of laboratory real rocks and numerical simulation experiments were verified and the macroscopic failure characteristics of the real and simulated rocks were determined to be similar. This study can help us correctly understand the mechanical properties of rocks with defects and provide theoretical guidance for practical rock engineering.

• 지질공학
• /
• 제26권4호
• /
• pp.571-581
• /
• 2016

To understand the mechanical properties of fault rocks, data from 584 in situ and laboratory tests on fault rocks from 33 tunnels were analyzed. The unit weights of the fault rocks range from 17.3 to $28.2kN/m^3$ and the cohesion and friction angles vary from 5 to 260 kPa and $14.7^{\circ}$ to $44.0^{\circ}$, respectively. The modulus of deformation and elasticity were generally < 200 MPa. In most cases, the uniaxial compressive strength was < 0.5 MPa, and Poisson's ratios were mainly 0.20-0.35. The mechanical properties of individual rock types were analyzed using box plots, revealing that the cohesion values and friction angles of shale and phyllite have relatively wide inter-quartile ranges and that the modulus of deformation and elasticity of shale have the lowest values of all rock types. In the analysis of mechanical properties by components of fault rocks, the largest values were shown in damage zones of individual rock types.