• 해양환경안전학회지
• /
• 제20권6호
• /
• pp.653-662
• /
• 2014

본 연구에서는 목포해양대학교의 실습선 새누리호를 대상으로 선박의 중앙집중 공조시스템에 공랭식 에어컨을 직접 설치하여 성능을 개선시킨 공기조화시스템으로 운전하였을 경우의 냉방 성능을 비교하고, 선실의 온열환경에 대한 실측조사를 통해서 향후 선박용 공기조화 설계 및 계획에 경험적 기초참고자료로 활용하고자 하는 것이다. 연구결과 동일한 외기조건에서 기존의 중앙집중방식 공조시스템과 개선된 공조시스템으로 운전하였을 경우, 모든 선실의 온도는 $24{\sim}28^{\circ}C$, 습도는 55~75 %로 쾌적한 조건임을 알 수 있었고, 발전기 부하를 측정결과 공기조화시스템의 성능개선에 따라 평균 부하 48 KW, 전부하시 부하율 약 8 %정도 감소하여 1일 연료소모량 FOC는 하루 평균 222[L/day]의 기름이 절약됨을 알 수 있었다. 또한 학생 선실(Cadet No. 21)은 기관실의 전열로 인해서 온도가 높게 나타났는데, 이것은 공기조화 설계 시 취출구 개수 및 전열부하를 고려하지 못한 결과로 판단된다.

• 한국산학기술학회논문지
• /
• 제18권1호
• /
• pp.585-591
• /
• 2017

본 연구에서는 터보과급기의 성능을 저해하는 주요 인자 중 하나인 마찰손실에 대한 연구를 수행하였다. 실제 엔진에서 빈번하게 사용되는 저속 구간에서의 승용차용 터보과급기의 마찰손실 측정 장치를 개발하고, 30,000~90,000rpm의 저속 영역에서 작동하는 터보과급기의 마찰손실을 측정하였다. 플로팅 베어링 타입의 승용차용 터보과급기를 실험 대상으로 선정하였으며, 마찰손실 측정 장치는 구동 모터, 오일 공급 시스템, 커플링으로 구성되었다. 실제 차량의 저속 운전 상황을 모사할 수 있도록 설계, 제작되었고, 회전속도, 오일 온도 및 압력을 실험 변수로 선정하였다. 또한, 마찰손실 측정 장치는 로드셀을 사용하여 발생하는 마찰 토크를 직접 측정하여 마찰손실을 산출하였으며, 마그네틱 커플링을 통해 구동 모터의 동력을 터보과급기 축에 전달하고, 오일 공급 시스템을 오일 온도 및 압력을 조절하였다. 온도 $60^{\circ}C$와 $90^{\circ}C$, 압력 4bar의 오일을 공급하는 상태에서 터보과급기가 회전수 30,000~90,000rpm으로 작동할 때 터보과급기 회전속도 증가할 때 마찰손실은 증가하며, 대략적으로 과급기 회전속도의 1.4~1.8 지수승에 비례함을 보이고 있다. 또한 오일온도가 $60^{\circ}C$에서 $90^{\circ}C$로 증가할 때 마찰손실은 최소 41%, 최대 63% 감소하였다.

• 한국산학기술학회논문지
• /
• 제15권6호
• /
• pp.4002-4006
• /
• 2014

자동차 배출가스는 자동차에 의해 발생되는 일산화탄소, 탄화수소, 납 외에 사람의 건강 또는 생활 환경에 피해를 일으킬 염려가 있는 물질을 말한다. 배출가스를 감소시키기 위해서 다양한 기술을 개발하는 것도 중요하지만 현재 사용되어 지고 있는 요소를 분석하여 최적의 상태를 찾는 것도 중요한 사항이라 여겨진다. 본 연구는 냉각수에 함유되는 부동액이 배출가스에 영향을 미칠 수 있음에 착안하여 현재 국내에서 시판되고 있는 5개 회사제품의 부동액을 권고 수준의 양을 냉각수에 함유시켜 HC, NOx, $CO_2$ 배출량을 측정하고 배출가스에 미치는 영향을 파악하고자 하였다. 또한, 5개회사 부동액 제품에 대하여 냉각팬 구동시간과 NOx 배출량과의 상관관계를 살펴보고자 하였다. 엔진오일의 온도는 자동차 검사 규격에 맞도록 $90{\sim}93^{\circ}C$에 맞추었고, 수동기어를 사용하는 소형승용차의 검사 규격 속도 $40{\pm}2Km/h$에서 수행하였다. 실험결과 D사 부동액이 팬 작동시간이 가장 짧고, $CO_2$, NOx 배출량이 가장 적게 나타났다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.533-536
• /
• 2009

The gasification technology is a very flexible and versatile technology to produce a wide variety products such as electricity, steam, hydrogen, Fisher-Tropsch(FT) diesels, Dimethyl Ether(DME), methanol and SNG(Synthetic Natural Gas) with near-zero pollutant emissions. Gasification converts coal and other low-grade feedstocks such as biomass, wastes, residual oil, petroleum coke, etc. to a very clean and usable syngas. Syngas is produced from gasifier including CO, $H_2$, $CO_2$, $N_2$, particulates and smaller quantities of $CH_4$, $NH_3$, $H_2S$, COS and etc. After removing pollutants, syngas can be variously used in energy and environment fields. The pilot-scale coal gasification system has been operated since 1994 at Ajou University in Suwon, Korea. The pilot-scale gasification facility consists of the coal gasifier, the hot gas filtering system, and the acid gas removal (AGR) system. The acid gas such as $H_2S$ and COS is removed in the AGR system before generating electricity by gas engine and producing chemicals like Di-methyl Ether(DME) in the catalytic reactor. The designed operation temperature and pressure of the $H_2S$ removal system are below $50^{\circ}C$ and 8 kg/$cm^2$. The iron chelate solution is used as an absorbent. $H_2S$ is removed below 0.1 ppm in the H2S removal system.

• 한국가스학회지
• /
• 제19권6호
• /
• pp.34-39
• /
• 2015

최근 차량용 에너지의 소비는 대부분 화석연료로부터 사용된다. 기존 화석 연료를 사용하는 자동차보다 친환경적이며 저렴하고 재생이 가능한 연료의 요구증대로 대체연료 자동차산업이 강조되고 있다. 오늘날 고옥탄가와 높은 자기발화온도 특징을 가지고 있는 천연가스는 저렴한 비용, 기존 화석연료보다 풍부한 매장으로 기존 스파크 점화엔진인 가솔린엔진의 대체에너지로 간주되고 있다. 본 연구는 기존 2리터 가솔린 엔진에 CNG 가스 분사시스템을 장착하여 전소 및 혼소 연료분사시스템을 설치하였다. 또한 CNG전소 및 가솔린/CNG 혼소차량의 ECU 제어전략을 최적화 하였다. 혼소차량에 대하여 NEDC모드 주행결과 가솔린 차량 대비 혼소차량의 CO2 저감율을 16%확인하였다. 또한 CO와 HC의 배기가스 배출량은 가솔린 차량과 동등한 수준을 확보하였다. 하지만 NOx의 배기가스 배출수준은 증가된 현상을 확인할 수 있었다.

• 한국해양공학회지
• /
• 제28권4호
• /
• pp.356-362
• /
• 2014

Wear and corrosion of the engine parts surrounded with combustion chamber is more serious compared to the other parts of the engine because temperature of the exhaust gas in a combustion chamber is getting higher and higher with increasing of using the heavy oil of low quality. Therefore, an optimum repair weldment as well as an available choice of the base metal for these parts are very important to prolong their lifetime in a economical point of view. It reported that there was an experimental result for repair weldment on the forged steel which would be generally used with piston crown material, however, it is considered that there is no study for the repair weldment on the cast steel of piston crown material. In this study, four types of electrodes such as 1.25Cr-0.5Mo, 0.5Mo Inconel 625 and 718 were welded with SMAW and GTAW methods on the cast steel which would be generally used with piston crown material. And the corrosion properties of weld metal, heat affected zone and base metal were investigated using electrochemical methods such as measurement of corrosion potential, anodic polarization curves, cyclic voltammogram and impedance etc. in 35% $H_2SO_4$ solution. In the cases of Inconel 625, 718, the weld metals and base metals exhibited the best and worst corrosion resistance respectively, however, 1.25Cr-0.5Mo and 0.5Mo indicated that corrosion resistance of the base metal was better than the weld metal. And the weld metal welded with electrodes of Inconel 625 revealed the best corrosion resistance among the electrodes, and Inconel 718 followed the Inconel 625. Hardness relatively also indicated higher value in the weld metal compared to heat affected zone and base metal. In particular, Inconel 718 indicated the highest value of hardness compared to other electrodes in the heat affected zone.

• 한국해양공학회지
• /
• 제30권4호
• /
• pp.334-340
• /
• 2016

The combustion chamber of a diesel engine is often exposed to a more serious wear and corrosion environment than other parts of the engine because its temperature increases as a result of using heavy oil of low quality. Therefore, repair and built-up welding methods must be performed on worn or corroded parts of the piston crown, exhaust valve, etc. from an economical point of view. In this study, Inconel 718 filler metal was used in repair welding on the groove of a forged steel specimen for a piston crown, along with built-up welding on the surface of another forged steel specimen. Then, the corrosion characteristics of the weld metal zone for the repair welding and the deposited metal zone for the built-up welding were investigated using electrochemical methods in a 35% H₂SO₄ solution. The deposited metal zone indicated better corrosion resistance than the weld metal zone, showing a nobler corrosion potential, higher impedance, and smaller corrosion current density. It is considered that metal elements with good corrosion resistance were generally included in the filler metal, and these elements were also greatly involved in the deposited meta by built-up welding, whereas the weld metal consisted of metal elements mixed with both the filler metal and base metal elements because of the molten pool produced by the repair welding. Finally, it is considered that the hardness of the weld metal was increased by the repair welding, whereas the built-up welding improved the corrosion resistance of the deposited metal.

• Tribology and Lubricants
• /
• 제34권5호
• /
• pp.197-207
• /
• 2018

Thermal deterioration of fuel due to long-term storage influences engine performance and causes malfunctions. Fuel stability is usually evaluated via heat resistance and thermal stability during a brief heat shock at high temperature; storage stability in this scenario means that there is very little change in the quality of the fuel during long-term storage. In addition, rubber-based products such as oil seals, O-rings, and rubber hoses can influence the quality of the fuel. When these rubber products are in contact with fuel, they can swell, mechanically weaken, and occasionally crack, thus leaking low molar weight rubber and additives including plasticizer and antioxidant into the fuel to degrade its properties and shorten its useful lifetime. This study determines the thermal stabilities of three kinds of synthetic fuels by evaluating their low temperature kinematic viscosities, chemical composition changes via GC analyses, gross heat of combustion, and color changes. We evaluate the compression set of O-rings by immersing one NBR and two FKM rubber O-rings in the three synthetic fuel samples in airtight containers at variable storage temperatures for six months; from this, we estimate the lifetimes of the O-rings using the Power law model. There were very little changes in the chemical compositions and gross heat of combustion after six months of the experiment. The lifetimes are thus dependent on the materials of the rubber products, and in particular, the FKM O-ring was calculated to have a theoretical lifetime of 200 to 5,700 years. These results indicate that the synthetic fuels maintain their physical properties even after long-term storage at high temperatures, and the FKM O-ring is suitable for long-term sealing of these fuels.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2009년도 춘계학술대회 논문집
• /
• pp.111-112
• /
• 2009

Diamond-like carbon (DLC) is a convenient term to indicate the compositions of the various forms of amorphous carbon (a-C), tetrahedral amorphous carbon (ta-C), hydrogenated amorphous carbon and tetrahedral amorphous carbon (a-C:H and ta-C:H). The a-C film with disordered graphitic ordering, such as soot, chars, glassy carbon, and evaporated a-C, is shown in the lower left hand corner. If the fraction of sp3 bonding reaches a high degree, such an a-C is denoted as tetrahedral amorphous carbon (ta-C), in order to distinguish it from sp2 a-C [2]. Two hydrocarbon polymers, that is, polyethylene (CH2)n and polyacetylene (CH)n, define the limits of the triangle in the right hand corner beyond which interconnecting C-C networks do not form, and only strait-chain molecules are formed. The DLC films, i.e. a-C, ta-C, a-C:H and ta-C:H, have some extreme properties similar to diamond, such as hardness, elastic modulus and chemical inertness. These films are great advantages for many applications. One of the most important applications of the carbon-based films is the coating for magnetic hard disk recording. The second successful application is wear protective and antireflective films for IR windows. The third application is wear protection of bearings and sliding friction parts. The fourth is precision gages for the automotive industry. Recently, exciting ongoing study [1] tries to deposit a carbon-based protective film on engine parts (e.g. engine cylinders and pistons) taking into account not only low friction and wear, but also self lubricating properties. Reduction of the oil consumption is expected. Currently, for an additional application field, the carbon-based films are extensively studied as excellent candidates for biocompatible films on biomedical implants. The carbon-based films consist of carbon, hydrogen and nitrogen, which are biologically harmless as well as the main elements of human body. Some in vitro and limited in vivo studies on the biological effects of carbon-based films have been studied [$2{\sim}5$].The carbon-based films have great potentials in many fields. However, a few technological issues for carbon-based film are still needed to be studied to improve the applicability. Aisenberg and Chabot [3] firstly prepared an amorphous carbon film on substrates remained at room temperature using a beam of carbon ions produced using argon plasma. Spencer et al. [4] had subsequently developed this field. Many deposition techniques for DLC films have been developed to increase the fraction of sp3 bonding in the films. The a-C films have been prepared by a variety of deposition methods such as ion plating, DC or RF sputtering, RF or DC plasma enhanced chemical vapor deposition (PECVD), electron cyclotron resonance chemical vapor deposition (ECR-CVD), ion implantation, ablation, pulsed laser deposition and cathodic arc deposition, from a variety of carbon target or gaseous sources materials [5]. Sputtering is the most common deposition method for a-C film. Deposited films by these plasma methods, such as plasma enhanced chemical vapor deposition (PECVD) [6], are ranged into the interior of the triangle. Application fields of DLC films investigated from papers. Many papers purposed to apply for tribology due to the carbon-based films of low friction and wear resistance. Figure 1 shows the percentage of DLC research interest for application field. The biggest portion is tribology field. It is occupied 57%. Second, biomedical field hold 14%. Nowadays, biomedical field is took notice in many countries and significantly increased the research papers. DLC films actually applied to many industries in 2005 as shown figure 2. The most applied fields are mold and machinery industries. It took over 50%. The automobile industry is more and more increase application parts. In the near future, automobile industry is expected a big market for DLC coating. Figure 1 Research interests of carbon-based filmsFigure 2 Demand ratio of DLC coating for industry in 2005. In this presentation, I will introduce a trend of carbon-based coating research and applications.