• Korean Journal of Materials Research
• /
• 제25권11호
• /
• pp.612-615
• /
• 2015

In this work, on-site corrosion behavior of heat resistant tubes of T91, used as components of a superheater in a power plant for up to 25,762 h, has been investigated using scanning electron microscopy(SEM), energy dispersive X-ray spectroscopy (EDS), and electron backscattered diffraction(EBSD), with the objectives of studying the composition, phase distribution, and evolution during service. A multi-layer structure of oxide scale was found on both the steamside and the fireside of the tube surface; the phase distribution was in the order of hematite/magnetite/spinel from the outer to the inner matrix on the steamside, and in the order of slag/magnetite/spinel from the outer to the inner matrix on the fireside. The magnetite layer was found to be rich in pores and cracks. The absence of a hematite layer on the fireside was considered to be due to the low oxygen partial pressure in the corrosion environment. The thicknesses of the hematite and of the slag-deposit layer were found to exhibit no significant change with the increase of the service time.

• Journal of the Korean Ceramic Society
• /
• 제45권11호
• /
• pp.688-693
• /
• 2008

This paper presents a study on the photocatalytic reaction about the composite particles of $TiO_2$-coated phosphors under visible light irradiation. Nanocrystalline titanium dioxide layers were directly coated on the alkaline earth aluminate phosphor, $CaAl_2O_4:Eu^{2+},\;Nd^{3+}$ particles by an sol-gel processing method. The photocatalytic reaction was analyzed with the degradation of methylene blue (MB) aqueous solution under UV and visible light irradiations. $TiO_2$-coated phosphor powders showed different photocatalytic mechanism, compared with pure $TiO_2$ (P-25, Degussa). Under UV-irradiation, $TiO_2$-coated phosphor powders showed slow photocatalytic reactivity in the early stage and fast in the latter, compared with that of pure $TiO_2$. However, $TiO_2$-coated phosphor powders showed much faster photocatalytic reactivity than that of pure $TiO_2$ under visible irradiation. In addition, the characterizations of the $TiO_2$-coated phosphor powders were conducted by a X-ray diffractometer (XRD), transmission electron microscope (TEM), and energy dispersive spectroscopy (EDS).

• Corrosion Science and Technology
• /
• 제10권6호
• /
• pp.212-217
• /
• 2011

In this study, corrosion characteristics of TiN and ZrN film on the abutment screw by arc-ion plating were investigated using a potentiodynamic anodic polarization test in deaerated 0.9% NaCl solution at $36.5{\pm}1^{\circ}C$. The surface morphologies of the coating layers before and after corrosion test were investigated by a field-emission scanning electron microscope (FE-SEM) and a energy dispersive x-ray spectroscopy (EDS). The surfaces of the TiN and ZrN coated abutment screws showed the smooth surfaces without mechanical defects like scratches which can be formed during the manufacturing process, compared with those of the non-coated abutment screw. The corrosion and passive current densities of TiN and ZrN coated abutment screws were lower than those of the non-coated abutment screw.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.227-227
• /
• 2008

CdS is II-VI semiconductor with a wide band gap of approximately 2.42 eV. CdS is the most popularly employed heterojunction partner to p-CdTe due to its similar chemical properties. The as-deposited films are annealed in Rapid Thermal Annealing (RTA) system in various atmosphere(Air, Vacuum and $N_2$) at $500^{\circ}C$. In this work, X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) of chemical bath deposited (CBD) CdS films on glass is carried out. In case of the annealed CdS films in $N_2$, grain size was larger than as-annealed films.

• Journal of Technologic Dentistry
• /
• 제35권4호
• /
• pp.343-352
• /
• 2013

Purpose: The purpose of this study was to investigate to effect of the ZrN coated on corrosion resistance and physical property of dental Co-Cr alloys using various instruments. Methods: The specimens were used, respectively, for experiment, Arc Ion plating was carried out for dental casting alloys using ZrN coated materials with nitrogen gas. ZrN coated surface of each specimen was observed with field emission scanning electron microscopy (FE-SEM), energy dispersive X-ray spectroscopy (EDS), vickers hardness tester, and electrochemical tester. Results: The current density of ZrN coated specimen was smaller than that of non-coated specimen in 0.9% NaCl solution. Pit nucleated at scratch of specimen. The pitting corrosion resistant |$E_{max}-E_{rep}$| increased in order of ZrN coated (110 mV), and non-coated wire (100 mV). Conclusion: The corrosion potential of the ZrN coated specimen was comparatively high. the surface of ZrN coated specimen was more smooth than that of other kinds of non-coated specimen. ZrN coated surface showed higher hardness than that of non-coated surface.

• Journal of Power System Engineering
• /
• 제18권6호
• /
• pp.58-63
• /
• 2014

This paper deals with the effects of counterpart materials on the wear behavior of thermally sprayed STS316 coatings. STS316 powders were flame-sprayed onto a carbon steel substrate. Dry sliding wear tests were performed using the applied loads of 15 N. AISI52100, $Al_2O_3$, $ZrO_2$ and $Si_3N_4$ balls were used as counterpart materials. Wear behavior of STS316 coatings against different counterpart materials were studied using a scanning electron microscope(SEM) and energy dispersive X-ray spectroscopy (EDS). The results show that the wear behavior of thermally sprayed STS316 coatings strongly depends on the type of counterpart material. Dominant wear mechanism was similar for all studied materials as failure of adhesion film except for Si3N4 used as counterpart material. In the case of Si3N4 used as counterpart material, dominant wear mechanism was abrasion.

• Tribology and Lubricants
• /
• 제27권6호
• /
• pp.351-355
• /
• 2011

Al/SiC composites were fabricated by thermal spray process, and the dry sliding wear tests were performed using the various sliding speed of 10, 30, 60 and 90 RPM through 1000 cycles. The applied load was 10 N and radius of wear track was 15 mm. Wear tracks on the Al/SiC composites were investigated using scanning electron microscope(SEM) and energy dispersive X-ray spectroscopy (EDS). In the case of sliding speed of 10 RPM, adhesive wear behavior caused by plastic deformation of composits surface was observed. In the cases of sliding speed of 30, 60, 90 RPM, abrasive wear behavior on the adhered layer formed by debris were observed. Through this study, it was found that the wear behavior of Al/SiC composites was mainly influenced by the sliding speed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.195.1-195.1
• /
• 2013

Cu는 금속 박막재료로서 높은 전기전도성을 지니고 있을 뿐만 아니라 Ag, Al, Pt 등 보다 비용이 저렴하여, 높은 전기전도성을 필요로 하는 박막 재료로써 폭넓게 사용되고 있다. 그러나, 낮은 기계적 특성을 지니고 있어서 interconnect와 같은 작은 단면적의 배선재료로 사용될 경우, 높은 전류밀도에 따른 electromigration 현상에 의하여 hillock 또는 void의 형성 등 박막재료의 변형이 생기게 되어서 전자소자의 수명이 단축된다는 단점이 있다. TiN은 금속재료 못지않은 높은 전기 전도성을 지니고 있을 뿐만 아니라, 금속재료에 비하여 높은 기계적 특성과 녹는점을 지니고 있어 다양한 분야로 사용되고 있다. 본 연구에서는 Cu와 TiN composite 박막을 soda-lime glass위에 증착하여 낮은 비저항 뿐만 아니라 Cu와 비교하여 기계적 특성이 향상된 박막을 제작하고자 하였다. Cu와 TiN composite 박막 증착을 위하여 DC reactive magnetron co-sputtering 장비를 사용하였으며, Cu와 Ti 타겟 power, Ar:N2 유량비(Flow rate)을 변화시켜 Cu와 Ti의 조성비 및 TiN의 결정성을 조절하였고, 이를 통하여 박막의 TiN 조성에 따른 낮은 비저항 값과 순수한 Cu 박막과 비교하여 높은 기계적 특성을 지닌 Cu-TiN 박막을 증착하였다. Cu-TiN composite 박막의 구조 및 조성은 SEM (Scanning Electron Microscope), EDS (Energy Dispersive Spectrometer), XPS (X-ray Photoelectron Spectroscopy)장비를 사용하여 분석하였으며, 전기전도도는 4-point probe를 사용하여 측정하였고, Knoop hardness 측정방법을 사용하여 박막의 기계적 특성을 측정하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.321.1-321.1
• /
• 2013

높은 광흡수 계수를 갖는 Cu(In,Ga)Se2(CIGS) 화합물 박막 소재는 고효율 태양전지 양산을 위해 가장 전도유망한 재료이나 상대적으로 매장량이 적은 In 및 Ga을 사용한다는 소재적 한계가 있다. Cu2ZnSnSe4(CZTSe) 혹은 Cu2ZnSnS4(CZTS)와 같은 Cu-Zn-Sn-Se계 화합물 반도체는 CIGS 내 희소원소인 In과 Ga이 범용원소인 Zn 및 Sn으로 대체된 소재로써 미래형 저가 태양전지 개발을 위해 활발히 연구되고 있는데, 그 화합물 조합에 따라 0.8eV부터 1.5eV까지의 에너지 밴드갭을 갖는 것으로 알려져 있다. 본 연구에서는 열분해법으로 CZTS 나노 입자를 합성하였다. 용매로 Oleylamine을 사용하였는데, $260{\sim}340^{\circ}C$의 온도 범위에서 5시간 30분 동안 CZTS 나노입자를 합성하였고, $300^{\circ}C$에서 5시간 30분~9시간까지 합성하였다. 헥산을 이용하여 원심분리기와 초음파세척기로 용매인 Oleylamine을 제거하였고, 진공오븐에서 건조된 CZTS 분말의 FE-SEM (Field Emission Scanning Electron Microscope), XRD (X-Ray Diffraction), EDS (Energy Dispersive Spectroscopy) 분석 등을 통해 합성온도에 따른 구조적, 화학적 조성 변화를 조사하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.140.2-140.2
• /
• 2013

Strong metal-support interaction effect is an important issue in determining the catalytic activity for heterogeneous catalysis. In this work, we report the catalytic activity of $Au/TiO_2$, $Au/Al_2O_3$, and $Au/Al_2O_3-CeO_2$ nanocatalysts under CO oxidation fabricated by arc plasma deposition (APD), which is a facile dry process with no organic materials involved. These catalytic materials were characterized by transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDS) and $N_2$-physisorption. Catalytic activity of the materials has measured by CO oxidation using oxygen, as a model reaction, in a micro-flow reactor at atmospheric pressure. Using APD, the catalyst nanoparticles were well dispersed on metal oxide powder with an average particle size (3~10 nm). As for catalytic reactivity, the result shows $Au/Al_2O_3-CeO_2$ nanocatalyst has the highest catalytic activity among three samples in CO oxidation, and $Au/TiO_2$, and $Au/Al_2O_3$ in sequence. We discuss the effects of structure and metal-oxide interactions of the catalysts on catalytic activity.