Purpose
The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70
The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70
Information and communication and home appliance industries, which were one of South Korea's main industries, are gradually losing their export share as their export competitiveness is weakening. This study objectively analyzed export competitiveness and suggested export-promising countries in order to help South Korea's information communication and home appliance industries improve exports. In this study, network properties, centrality, and structural hole analysis were performed during network analysis to evaluate export competitiveness. In order to select promising export countries, we proposed a new variable that can take into account the characteristics of an already established International Trade Network (ITN), that is, the Global Value Chain (GVC), in addition to the existing economic factors. The conditional log-odds for individual links derived from the Exponential Random Graph Model (ERGM) in the analysis of the cross-border trade network were assumed as a proxy variable that can indicate the export potential. In consideration of the possibility of ERGM linkage, a parametric approach and a non-parametric approach were used to recommend export-promising countries, respectively. In the parametric method, a regression analysis model was developed to predict the export value of the information and communication and home appliance industries in South Korea by additionally considering the link-specific characteristics of the network derived from the ERGM to the existing economic factors. Also, in the non-parametric approach, an abnormality detection algorithm based on the clustering method was used, and a promising export country was proposed as a method of finding outliers that deviate from two peers. According to the research results, the structural characteristic of the export network of the industry was a network with high transferability. Also, according to the centrality analysis result, South Korea's influence on exports was weak compared to its size, and the structural hole analysis result showed that export efficiency was weak. According to the model for recommending promising exporting countries proposed by this study, in parametric analysis, Iran, Ireland, North Macedonia, Angola, and Pakistan were promising exporting countries, and in nonparametric analysis, Qatar, Luxembourg, Ireland, North Macedonia and Pakistan were analyzed as promising exporting countries. There were differences in some countries in the two models. The results of this study revealed that the export competitiveness of South Korea's information and communication and home appliance industries in GVC was not high compared to the size of exports, and thus showed that exports could be further reduced. In addition, this study is meaningful in that it proposed a method to find promising export countries by considering GVC networks with other countries as a way to increase export competitiveness. This study showed that, from a policy point of view, the international trade network of the information communication and home appliance industries has an important mutual relationship, and although transferability is high, it may not be easily expanded to a three-party relationship. In addition, it was confirmed that South Korea's export competitiveness or status was lower than the export size ranking. This paper suggested that in order to improve the low out-degree centrality, it is necessary to increase exports to Italy or Poland, which had significantly higher in-degrees. In addition, we argued that in order to improve the centrality of out-closeness, it is necessary to increase exports to countries with particularly high in-closeness. In particular, it was analyzed that Morocco, UAE, Argentina, Russia, and Canada should pay attention as export countries. This study also provided practical implications for companies expecting to expand exports. The results of this study argue that companies expecting export expansion need to pay attention to countries with a relatively high potential for export expansion compared to the existing export volume by country. In particular, for companies that export daily necessities, countries that should pay attention to the population are presented, and for companies that export high-end or durable products, countries with high GDP, or purchasing power, relatively low exports are presented. Since the process and results of this study can be easily extended and applied to other industries, it is also expected to develop services that utilize the results of this study in the public sector.
The sinus tympani is subject to great variability in the size, shape and posterior extent. A heavy compact bony zone, especially in the posterior portion and the narrow space between the facial nerve and posterior semicircular canal are the limitation of surgical approach. The facial recess should be opened, creating a wide connection between the mesotympanum and mastoid in the Intact canal wall tympanoplasty with mastoidectomy. The surgically created limits of the facial recess are the facial nerve medially, the chorda tympani laterally and the bone adjacent to the incus superiorly. Using adult Korean's thirty-five temporal bones, the authors measured the osteologic reslationship in the posterior tympanum, especially sinus tympani and facial recess. The result was as followed. 1. The average distance from the anterior end of the pyramidal eminence. 1) to the edge of the sinus tympani directly posterior was 2.54(1.05-5.40)mm. 2) to the maximum posterior extent was 3.22(1.25-7.45)mm. 3) to the maximum cephaled extent was 0.67 (0.40-1.75)mm. 2. The boundary of the sinus tympani was 82.9% from the lower margin oval window to the upper margin round window niche. 3. The deepest part of the sinus tympani was 62.9% in the mid portion, between the ponticulus and subiculum. 4. The oblique dimension from the fossa incudis above to the hypotympanum below was 8.13(7.90-9.55)mm. 5. The transverse dimensions midway between the oval window above and round window below was 3.00(2.85-3.45)mm. 6. The transverse dimension at the level of the fossa incudis was 1.81(1.40-2.15)mm. 7. The facial nerve dehiscence was 14.3%. 8. Anterior-posterior diameter of the footplate was 2.98(2.85-3.05) mm. 9. The average distance from the footplate. 1) to the cochleariform process was 1.42(1.35-1.55) mm. 2) to the round window niche was 1.85(1.45-2.10) mm.
Most domestic companies, with the exclusion of major firms, are reluctant to implement a supply chain management (SCM) network into their operations. Most small- and medium-sized enterprises are not even aware of SCM. Due to the inherent total-systems efficiency of SCM, it coordinates domestic manufacturers, subcontractors, distributors, and physical distributors and cuts down on cost of inventory control, as well as demand management. Furthermore, a lack of SCM causes a decrease in competitiveness for domestic companies. The reason lies in the fundamentality of SCM, which is the characteristic of information sharing, process innovation throughout SCM, and the vast range of problems the SCM management tool is able to address. This study suggests the contemplation and reformation of the current SCM situation by analyzing the SCM strategic plan, discourses and logical discussions on the topic, and a successful case for adapting SCM; hence, the study plans to productively "process" SCM. First, it is necessary to contemplate the theoretical background of SCM before discussing how to successfully process SCM. I will describe the concept and background of SCM in Chapter 2, with a definition of SCM, types of SCM promotional activities, fields of SCM, necessity of applying SCM, and the effects of SCM. All of the defects in currently processing SCM will be introduced in Chapter 3. Discussion items include the following: the Bullwhip Effect; the breakdown in supply chain and sales networks due to e-business; the issue that even though the key to a successful SCM is cooperation between the production and distribution company, during the process of SCM, the companies, many times, put their profits first, resulting in a possible defect in demands estimation. Furthermore, the problems of processing SCM in a domestic distribution-production company concern Information Technology; for example, the new system introduced to the company is not compatible with the pre-existing document architecture. Second, for effective management, distribution and production companies should cooperate and enhance their partnership in the aspect of the corporation; however, in reality, this seldom occurs. Third, in the aspect of the work process, introducing SCM could provoke corporations during the integration of the distribution-production process. Fourth, to increase the achievement of the SCM strategy process, they need to set up a cross-functional team; however, many times, business partners lack the cooperation and business-information sharing tools necessary to effect the transition to SCM. Chapter 4 will address an SCM strategic plan and a case study of LG Electronics. The purpose of the strategic plan, strategic plans for types of business, adopting SCM in a distribution company, and the global supply chain process of LG Electronics will be introduced. The conclusion of the study is located in Chapter 5, which addresses the issue of the fierce competition that companies currently face in the global market environment and their increased investment in SCM, in order to better cope with short product life cycle and high customer expectations. The SCM management system has evolved through the adaptation of improved information, communication, and transportation technologies; now, it demands the utilization of various strategic resources. The introduction of SCM provides benefits to the management of a network of interconnected businesses by securing customer loyalty with cost and time savings, derived through the consolidation of many distribution systems; additionally, SCM helps enterprises form a wide range of marketing strategies. Thus, we could conclude that not only the distributors but all types of businesses should adopt the systems approach to supply chain strategies. SCM deals with the basic stream of distribution and increases the value of a company by replacing physical distribution with information. By the company obtaining and sharing ready information, it is able to create customer satisfaction at the end point of delivery to the consumer.
The existing management job of research expenses has been divided into three parts: budget planning, budget draw-up, and exact settlement of budget. However, it caused some problems. Under this current circumstance it is required to obtain research expenses steadily, to operate efficiently and to use them clearly to solve such problems. As a result of a study on data warehouse development process of existing system integration company (Inmon, IBM) to reflect current trend described above, data warehouse development process of Inmon uses systematic and gradual access as a classical development cycle method. It causes overlap and feedback to the previous step in the process of each step Is requested. And another problem that it is difficult to toil what function refers and corrects data because functions and data are separated during performing development process at data warehouse development process of IBM is caused. Integrated management data warehouse development process of research expenses in the enterprise environment which applies UML at planning and analysis step, design step and implement and test step is suggested in this paper. Information retrieval agent uses existing budget plan DB, budget draw-up DB and budget settlement DB to find out information that a user wants to know. Information retrieval agent collects and saves information at integration database and information integration agent extracts, transports, transforms and loads the data. Information integration agent reduces a user's efforts to access to a number of information sources and check each of them. It also screens out data that a user may not need. As a result, integrated management data warehouse development process of research expenses in the enterprise environment reflects a user's requirements as much as possible and provides various types of information to make a decision which is needed to establish the policy of research expense management. It helps an end user approach his/her desired analysis information quickly and get various data from the comprehensive viewpoint rather than the fragmentary viewpoint. Furthermore, as it integrated three systems into one, it is possible to share data, to integrate the system, to reduce operating expenses and to simplify supporting environment for the decision making.
This essay attempts to reveal how taste spontaneously cultivates and why it is necessary for cultivating taste to edify our personality and to develop culture. It is a key of the solution of the problems that taste always reflects its judgment through pleasure. Because the grounds of the universal validity of the judgment of taste are found, whenever taste tests the validity of its own judgment, the so-called 'delight of discovery' makes taste cultivate itself. For having the moral personality, we need to practice spontaneously the morality of our own behaviour and for judging whether an artwork to represent the period is succeeded or not, we need to have a high insight to select the cultural heritage. But the autonomous thinking can delightfully be made a habit, judging the beauty of artworks. In the main body of this essay, it is determined from the three examples of the negative judgment of taste which Kant suggested in deduction. According to Kant, the negative judgment of taste means that the beautiful work is displeased, but what it asserts is that taste is cultivated. I formalize the methods of reflection of taste revealed in three negative judgments of taste into'resisting', 'indicating of error', 'self-retracting'.(Chapter 2) And from this, I emphasize the necessity to cultivate taste in the way that these methods of the cultivation of taste can affect building our personality by stimulating our reason to have interest in moral(Chapter 3) and in the way that taste directly judges the product of cultural succession.(Chapter 4) In the end of last chapter, I examine further essentially the method of the reflection of taste, to inquire into how to enable it.(Chapter 5) Especially, I try to illuminate its grounds through Schiller's concept of the "impulse of amusement(Spieltrib)", because his explanation helps us to understand the dynamics of taste's delight of discovery. Although the abilities of mind conflict with each other, taste has the characters that it reflects to encourage them for each other and that it is vitalized by its own activity. We, as it were, can pleasantly handle two tasks, because taste makes the impulse of amusement from conflictive impulses in mind. In conclusion, I state that we have to experience directly the impulse of amusement like creative artist, because it is maximized from creation.
Despite the increasing importance of urban parks' ecological functions in dealing with the climate crisis, ecological parks are not clearly defined in Korea's legal system. Numerous ecological parks created nationwide cannot be systematically designated and managed due to various legal bases and varying management authorities. It is important to clarify the legal status of ecological parks in order to lead the ecological paradigm shift of urban parks and to improve the natural park system for a comprehensive and integrated approach to protect the national ecosystem. To this end, related laws were analyzed to identify problems and to draw directions for legislative improvement. Through the literature review of relevant laws, acts, and ordinances, six major directions for improvement were suggested based on the analysis of problems. First, the legal status of ecological parks in the administrative dichotomy of the current park system is ambiguous, and ecological parks should be clarified through the revision of park-related laws. Second, an ecological park can be defined as a sustainable park created and managed in an ecological manner, promoting the protection and restoration of the ecosystem, conservation, and promotion of biodiversity, and balancing nature observation, ecological learning, and leisure activities. Third, the role of the state and local governments should be systematically revised to lead to a new park planning and management model through new governance. Fourth, since the characteristics of ecological parks are affected by individual laws, the possibility of overlapping ecological parks for other uses should be allowed. Fifth, detailed guidelines and standard ordinances need to be enacted to meet the goals, principles, and facilities of ecological parks. Lastly, along with the revision of the laws, ordinances by local governments also need to be more concrete. This study, which tracks various legal realities related to ecological parks, can contribute to policymaking that can systematize the foundation for the creation of ecological parks to preserve nationwide ecosystems and provide citizens with opportunities to experience and learn about nature.
The competence of newly graduated nurses is based on various clinical expriences gained when they were students. Therefore, instructors of nursing students, professors in nursing schools or directors in hospitals must play a critical role in assisting them to obtain various knowledge and experienced nursing skills. The purpose of this study was to investigate nursing care activities and nursing care hours practiced by nursing students in a general hospital. The subject students were total 214 nursing students, 2nd graders(sophomores) and 3rd graders(juniors) from 5 Junior Nursing Colleges in Seoul and they practiced at S general hospital to gain clinical experience. The data were collected for 4 days. The tools for this study were the direct nursing care activity list consisted of 15 nursing areas and the indirect nursing care activity list consisted of 9 nursing areas. The subject students were supposed to record their own score. The results of this study are ; 1. The nursing care hours per nursing student 1) The average total nursing care hours a day per each nursing student are 362.65 mins(6.04hr), the direct nursing care hours per each nursing stuent are 202.09 mins(direct nursing care rate 56.0%) and it is higher than the indirect nursing care hours, 159.75mins(indirect nursing care rate 44.0%). The direct nursing care rate of each student by a team approach in the evening shift(56.3%) is higher than that in the day shift(55.8%). 2) The hours of checking vital signs are the longest(47.35mins) among the direct nursing care activites and next is in order of counseling 8l emotional support, nurse rounds, and accompaning a patient during examination. The hours of reporting are the longest(32.39mins) among the indirect nursing care activites, and next is the activities related to education such as reviewing chart, looking up references, etc. 3) The freqency of checking vital signs practiced by nursing student is the highest(the average of 55.7 times) among the direct nursing care activities and next is in order of nurse rounds, assistance of feeding, and counseling & emotional support. The required time for nursing students to accompany their patient during examination is the longest(20.7mins) and next are in order of restriction on patient' activity, orientated by a head nurse, skin care, sitz bath, bathing & hair shampoo, and assisting with patients' exercise. 2. The nursing care hours per grader 1) The average hours of total nursing care per a nursing student are 369.2mins(6.2hrs) to 2nd graders, 355.9mins(5.9 hrs) to third graders. The direct nursing care rate per each nursing student to 3rd graders(59.3%) was higher than that to End graders(52.8%). 2) For 2nd graders, the highly marked nursing activities are teaching associated with direct nursing care activities such as drawing up papers, looking up references, reviewing charts, and being orientated by staff nurses. For 3rd graders, measurments, observations, and nurse rounds in indirect nursing care activities are taken highly 3) The most frequent practice of the nursing care activites is checking vital signs : 65 times to 3rd graders and 46.5 times to 2nd graders. Our suggestions based on the results of this study are : 1. It is recommanded to repeat the same designed study in a variety of clinical fields for further study. 2. It is recommanded to collect data not by self-record method but by observated method. 3. It is needed for nursing instructors in Nursing Schools and in hospitals to develop the guidelines and check-list of clinical practice courses.