• Proceedings of the SAREK Conference
• /
• 2004.06a
• /
• pp.33-33
• /
• 2004

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.28 no.2
• /
• pp.87-92
• /
• 1986

The differential equation, which can determine the dynamic critical loads for low parabcoic arches, is derived in this study. The dynamic critical loads of the parabolic arches subjected to a concentrated step load are nummerically analyzed for the changes of load positions. In cases of arches with different end conditions (both hinged, fixed hinged, both fixed), the effect of end conditions and that of the rises are investigated in detail. The summary of the results are the following: 1)The snapthrough does not occur when the rise of arch is very low, and the bifurcation appears clearly as the rise of arch increases. 2)The regions in which the dynamic critical loads are not defined for the both ends fixed are broader than that for the both ends hinged. 3)For all case, the load positions of minimum dynamic critical loads exsit at the near position from the end hinged. Thus, the results obtained in present study show that the magnitude of dynamic critical loads, the load positions of minimum dynamic critical loads and the regions in which the dynamic critical loads are not defined depend on end conditions of arches.

• Tribology and Lubricants
• /
• v.26 no.6
• /
• pp.329-335
• /
• 2010

Recently, the End-milling processing is needed the high-precise technique to get a good surface roughness and rapid time in manufacturing of precision machine parts and electronic parts. The optimum surface roughness has an effect on end-milling working condition such as, cutting direction, spindle speed, feed rate and depth of cut, and so on. It needs to form the correlation of working conditions and surface roughness. Therefore this study was carried out to presume of surface roughness on end-milling working condition of Al7075 by regression analysis. The results was shown that the coefficient of determination($R^2$) of regression equation had a fine reliability of 87.5% and nonlinear regression equation of surface rough was made by multiple regression analysis.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.947-950
• /
• 2000

The purpose of this paper is to investigate the effect of the helix angle of endmilling cutter on the cutting characteristics of inconel 718 in up endmilling. To this end cutters with helix angle of $20^\circ$, $30^\circ$, $40^\circ$ and $50^\circ$ degree have been prepared. And a modified cutting force model in up end milling process is presented. Using this cutting force components of 4-tooth endmills with various helix angles have been predicted. Predicted values of cutting force components are well coincide with the measured ones. As helix angle increases overlapping effects of the active cutting edges increase.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.553-556
• /
• 2003

End-milling have been used in the industrial world because it is very effective to the manufacture of mechanical parts with various shape. Recently the end-milling processing is needed the high-precise technique with good surface roughness and rapid time in aircraft, automobile part and molding industry. Therefore this study carried to decide the optimum cutting condition for surface roughness and rapid manufacturing time using design of experiment and ANOVA. From the results of experimentation, surface roughness have an effect on cutting direction, spindle speed and depth of cut. And then the optimum condition used Taguchi design is upward cutting in cutting direction, 600rpm in spindle speed, 240mm/min feed rate, 2mm in axial depth of cut and 0.25mm radial depth of cut. By using design of experiment, it is effectively represented shape characteristics of working surface in end-milling.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.3 no.4
• /
• pp.37-42
• /
• 2004

End-milling have been widely used in aircraft, automobile part and moulding industry. However, various working factors such as spindle speed, feed rate and depth of cut in end-milling have an effect on spindle vibration. There it is demanded the quantitative analysis of spindle vibration in order to get the optimum surface roughness. This study was carried out to analyze an influence of working factors on spindle vibration by design of Experiment. The results are shown that mathematical model of regression equation for an influence of working factors on vibration acceleration of spindle in end-milling by regression analysis is presented.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1822-1827
• /
• 2003

End-milling have been used widely in industrial system because it is effective to a material manufacturing with various shape. Recently the end-milling processing is needed the high-precise technique with good surface roughness and rapid time in precision machine part and electronic part. The optimum surface roughness has an effect on end-milling condition such as, cutting direction, spindle speed, feed rate and depth of cut, etc. Therefore this study was carried out to presume for mutual relation of end-milling condition to get the optimum surface roughness by regression analysis. The results shown that coefficient of determination($R^{2}m$) of regression equation has a fine reliability over 80% and regression equation of surface rough is made by regression analysis.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.33-33
• /
• 2009

This study is to develop the resistance welding apparatus and investigate the welding characteristics of Zircaloy-4 end-plate of fuel bundle in the cases of the resistance welding and the laser beam welding. The welding parameters which affect the weld nugget and the torque values have been also compared. The effect of the torque strength of end-plate welding using by the resistance welding and the laser beam welding has been studied and optimum conditions of Zircaloy-4 end-plate welding have been found. Futhermore, micro-structures and micro-hardness of the resistance welded specimens have been also compared.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.4 s.97
• /
• pp.229-236
• /
• 1999

The surface, generated by end milling operation, is deteriorated by tool runout, vibration, tool wear and tool deflection, etc. Among them, the effect of tool deflection on surface accuracy is analyzed. Surface generation model for the prediction of the topography of machined srufaces has been developed based on cutting mechanism and cutting tool geometry. This model accounts for not only the ideal geometrical surface, but also the deflection of tool due to cutting force. For the more accurate prediction of cutting force, flexible end mill model is used to simulate cutting process. Computer simulation has shown the feasibility of the surface generation system. Using developed simulation system, the relations between the shape of end mill and cutting conditions are analyzed.

• Journal of Welding and Joining
• /
• v.15 no.6
• /
• pp.85-95
• /
• 1997

This study is to investigate the optimum conditions of Nd:YAG laser beam welding for Zircaloy-4 end cap closure by optical fiber transmission. Laser welding parameters which affect the penetration depth and bead width were experimentally examined using the various beam radius by the beam quality analyzer, joint geometries of end cap and the laser parameters which mean pulse width, repetition rate and pulse energy. Also, an optimum welding speed and the effect of assistant gas with varying the flow rate of He were investigated. We found that the laser average power for the end cap welding will be 230W and rotation speed must not exceed 8 RPM, the best position of focus using optical fiber with 600.mu.m will be 2 to 3mm below the surface of the material.