• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.619-624
• /
• 2002

A prestressed/precast concrete system was used to build the new Asian Olympic Stadium Project in Pusan, Korea. The stadium(mainly intended for cycle racing) is designed for the 2002 Asian Olympic Games and has a seating capacity of 20,000 spectators plus a few private suites. More than 1300 prestressed/precast components were used and they include single columns, primary beams, cantilever beams, double riser stands, and double tees. Especially, a total of 24 cantilever beams is used on the fourth story for the stands and double tees. These 8m long beams are post-tensioned to prevent cracking, to increase their durability and to serve serviceability by vibration. A cantilever section with cast-in-place topping is 800mm wide and 1500mm deep. Cantilever beams are connected to the column with the corbel by cast-in place concrete. Bonded post-tensioning tendons were assembled at the job site. Dead-end anchorages were installed in the end of cantilever beams and live-end anchorage is the opposite of them. This article presents the geometric layouts, design features and so on.

• Computers and Concrete
• /
• 제26권5호
• /
• pp.397-409
• /
• 2020

The current study targets to estimate the contribution of the end-anchored FRP composites in resisting shear force using a soft computing tool i.e., adaptive neuro-fuzzy inference system (ANFIS). A total of 107 sets of data accumulated from literature was utilized for the development and evaluation of the current ANFIS model. A comparative analysis between the ANFIS predictions and the acquired experimental results has shown that the ANFIS predictions are in very good agreement with that of experimental ones. Additionally, the accuracy of the current ANFIS model has been weighed up against the estimates of nine widely adopted design guidelines. Based on various statistical parameters, it has been deduced that the effectiveness of the current ANFIS model is better than the considered design guidelines. Besides this, a parametric study was carried out to explore the combined effect of different parameters as well as the impact of individual parameters.

• 대한건축학회논문집:구조계
• /
• 제36권4호
• /
• pp.123-133
• /
• 2020

The purpose of this study is to analyze the method of retrofitting flexural strength and the flexural performance of retrofitted shear walls. There are various ways to reinforce the flexural strength of reinforced concrete shear wall structural systems that have already been built, in the case of that, the external force is increased, and the internal force is insufficient. However, there are various problems, such as excessive flexural stiffness after reinforcement and increasing the thickness and length of the wall. We have developed a retrofit method to solve these problems. The wall end is excavated to place the required vertical rebars, and concrete is poured after placing rebars. This is the same concept as creating wall end boundary elements later on. We also studied the anchorage method of reinforcement and the interaction method between the retrofitting end and the existing wall. The flexural test results for the reinforced concrete shear wall using the studied retrofit method can be predicted according to the sectional analysis and FEM analysis, and there are differences in the plastic hinge length, crack propagation, stiffness degradation and energy dissipation due to the bending depending on the vertical rebar ratio of wall end.

• 콘크리트학회지
• /
• 제8권4호
• /
• pp.201-211
• /
• 1996

최근에 계속적으로 발전하고 있는 역학적 모델은 배근상세에 있어서 과거의 경험적인 방법을 대신 할 수 있을 것으로 기대된다. 본 연구에서는 프리스트레스트 콘크리트 부재의 단부 정착부의 배근상세를 위한 역학적 모델을 제안하였다. 제안된 모델에서는 콘크리트의 2축응력상태, 나선철근 배근 상태, 전단 마찰 파괴 등을 고려하였다. 제안된 모델과 다른 연구자의 스터럿 타이 모델, 비선형 유한 요소 해석을 대표적인 실험결과와 비교하였다. 제안된 방법은 파괴하중뿐만 아니라 파괴형태의 예측에 있어서 우수한 것으로 밝혀졌다. 제안 모델은 2차원 해석에 기초한 역학적 모델 및 비선형 해석으로 설명이 불가능한 3차원 파괴 형태를 잘 예측할 수 있음을 알 수 있다.

• 대한치과교정학회지
• /
• 제45권4호
• /
• pp.171-179
• /
• 2015

Objective: To compare dentoalveolar and skeletal changes produced by the pendulum appliance (PA) and the distal screw appliance (DS) in Class II patients. Methods: Forty-three patients (19 men, 24 women) with Class II malocclusion were retrospectively selected for the study. Twenty-four patients (mean age, $12.2{\pm}1.5years$) were treated with the PA, and 19 patients (mean age, $11.3{\pm}1.9years$) were treated with the DS. The mean distalization time was 7 months for the PA group and 9 months for the DS group. Lateral cephalograms were obtained at T1, before treatment, and at T2, the end of distalization. A Mann-Whitney U test was used for statistical comparisons of the two groups between T1 and T2. Results: PA and DS were equally effective in distalizing maxillary molars (4.7 mm and 4.2 mm, respectively) between T1 and T2; however, the maxillary first molars showed less distal tipping in the DS group than in the PA group ($3.2^{\circ}$ vs. $9.0^{\circ}$, respectively). Moreover, significant premolar anchorage loss (2.7 mm) and incisor proclination ($5.0^{\circ}$) were noted in the PA group, whereas premolar distal movement (1.9 mm) and no significant changes at the incisor ($0.1^{\circ}$) were observed in the DS group. No significant sagittal or vertical skeletal changes were detected between the two groups during the distalization phase. Conclusions: PA and DS seem to be equally effective in distalizing maxillary molars; however, greater distal molar tipping and premolar anchorage loss can be expected using PA.

• 한국지진공학회논문집
• /
• 제28권3호
• /
• pp.129-139
• /
• 2024

In this study, the SBC system, a new mechanical joint method, was developed to improve the constructability of precast concrete (PC) beam-column connections. The reliability of the finite element analysis model was verified through the comparison of experimental results and FEM analysis results. Recently, the intermediate moment frame, a seismic force resistance system, has served as a ramen structure that resists seismic force through beams and columns and has few load-bearing walls, so it is increasingly being applied to PC warehouses and PC factories with high loads and long spans. However, looking at the existing PC beam-column anchorage details, the wire, strand, and lower main bar are overlapped with the anchorage rebar at the end, so they do not satisfy the joint and anchorage requirements for reinforcing bars (KDS 41 17 00 9.3). Therefore, a mechanical joint method (SBC) was developed to meet the relevant standards and improve constructability. Tensile and bending experiments were conducted to examine structural performance, and a finite element analysis model was created. The load-displacement curve and failure pattern confirmed that both the experimental and analysis results were similar, and it was verified that a reliable finite element analysis model was built. In addition, bending tests showed that the larger the thickness of the bolt joint surface of the SBC, the better its structural performance. It was also determined that the system could improve energy dissipation ability and ductility through buckling and yielding occurring in the SBC.

• Structural Engineering and Mechanics
• /
• 제43권4호
• /
• pp.459-473
• /
• 2012

Post-tensioned concrete voided slab girders are widely used in highway bridge constructions. To obtain greater section hollow rate and reduce the self-weight, the plate thickness of slab girders are designed to be small with the adoption of flat anchorage system. Since large prestress is applied to the anchor end section, it was found that longitudinal shear cracks are easy to occur along the voided slab girder. The reason is the existence of great shearing effect at the junction area between web and bottom (top) plate in the anchor end section. This paper focuses on the longitudinal anti-cracking problem at the anchor end of post-tensioned concrete voided slab girders. Two possible models for longitudinal anticracking analysis are proposed. Differential element analysis method is adopted to derive the solving formula of the critical cracking state, and then the practical analysis method for longitudinal anti-cracking is established. The influence of some factors on the longitudinal anti-cracking ability is studied. Results show that the section dimensions (thickness of bottom, web and top plate) and prestress eccentricity on web plate are the main factors that influence the anti-cracking ability. Moreover, the proposed method is applied into three engineering examples to make longitudinal anti-cracking verification for the girders. According to the verification results, the design improvements for these girders are determined.

• Structural Engineering and Mechanics
• /
• 제77권1호
• /
• pp.75-87
• /
• 2021

The present study pertains to the introduction of two new types of grip adaptor for universal testing machines, namely Polyvinyl Chloride (PVC) and Polyoxymethylene (POM) grip adaptors, and their application to tension testing of FRP bars with different fiber and surface finish types. The tabs are connected to the FRP bar sample with the help of mechanical anchors, i.e. bolts. These new adaptors offer vital superiorities over the existing end tab designs (anchors with filling material or mechanical anchorage), including the reduction in the time and labor for production, reusability and the mild nature, i.e. low hardness of the tab material, which retards and even prevents peeling and crushing in the gripping regions of an FRP sample. The methods were successfully applied to FRP bars with different types of fiber (CFRP, GFRP and BFRP) and different types of surface texture (ribbed, wrapped, sand-coated and wound). The test results indicated that the both types of end caps prevented slip of the bar, crushing and peeling in the gripping zone. The mechanical properties from the material tests with the new caps were in perfect agreement with the ones from the material tests with steel tubular caps.

• Structural Engineering and Mechanics
• /
• 제17권3_4호
• /
• pp.357-378
• /
• 2004

Nonlinear dynamic analysis of a reinforced concrete (RC) frame under earthquake loading is performed in this paper on the basis of a hysteretic moment-curvature relation. Unlike previous analytical moment-curvature relations which take into account the flexural deformation only with the perfect-bond assumption, by introducing an equivalent flexural stiffness, the proposed relation considers the rigid-body-motion due to anchorage slip at the fixed end, which accounts for more than 50% of the total deformation. The advantage of the proposed relation, compared with both the layered section approach and the multi-component model, may be the ease of its application to a complex structure composed of many elements and on the reduction in calculation time and memory space. Describing the structural response more exactly becomes possible through the use of curved unloading and reloading branches inferred from the stress-strain relation of steel and consideration of the pinching effect caused by axial force. Finally, the applicability of the proposed model to the nonlinear dynamic analysis of RC structures is established through correlation studies between analytical and experimental results.

• 한국전산구조공학회논문집
• /
• 제18권1호
• /
• pp.1-12
• /
• 2005

이 논문에서는 단면성질을 나타내는 모멘트-곡률 관계에 토대를 둔 해석모델을 제안하였다. 기존의 제안된 해석방법에서는 모멘트-곡률 관계가 완전부착을 가정한 휨거동만을 주요한 거동으로 가정하여 구조물의 응답을 과소평가하고 강성을 과대평가한 것과는 달리 제안된 해석 방법에서는 접합부의 부착슬립에 의한 강체변형을 산정할 수 있는 알고리즘을 개발하였고 나아가 등가휨강성을 이용하여 부착슬립에 의한 강체변형을 고려한 철근콘크리트 구조물의 해석을 수행하였다. 또한 모멘트-곡률 관계를 철근의 항복점을 기준으로 두개의 직선으로 간편화 시킴으로써 해석의 효율성을 높이는 한편 고려해야 할 비선형 거동특성을 효과적으로 반영하였다. 마지막으로 철근콘크리트 구조물의 비선형 해석에 대한 제안된 모델식의 적용성을 검증하기 위하여 해석결과와 실험값들의 비교를 수행하였다.