• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2001.10a
• /
• pp.128-131
• /
• 2001

The purpose of this study is to investigate the application of Column Jet Method(CJM) as countermeasure against settlement and slope sliding of existing marine structure due to embankment load behind reclaimed revetment. CJM is to make high-strengthened body by compacting and grouting cement mortar after forming artificial space in the ground with ground relaxition machine or high pressure water jetting. Before the ground was reinforced by CJM, the result of slope stability analysis was not satisfy the allowable safe ratio, but after the ground was reinforced by CJM, the stability of slope was over the allowable safe ratio and stable, Therefor, the application of CJM to restraint settlement and sliding of marine structure was very satisfactory.

• Wind and Structures
• /
• v.26 no.1
• /
• pp.35-43
• /
• 2018

This paper describes the effect of different testing parameters (configuration of infrastructure and truck position on road) on truck aerodynamic coefficients under cross wind conditions, by means of a numerical approach known as Large Eddy Simulation (LES). In order to estimate the air flow behaviour around both the infrastructure and the truck, the filtered continuity and momentum equations along with the Smagorinsky-Lilly model were solved. A solution for these non-linear equations was approached through the finite volume method (FVM) and using temporal and spatial discretization schemes. As for the results, the aerodynamic coefficients acting on the truck model exhibited nearly constant values regardless of the Reynolds number. The flat ground is the infrastructure where the rollover coefficient acting on the truck model showed lowest values under cross wind conditions (yaw angle of $90^{\circ}$), while the worst infrastructure studied for vehicle stability was an embankment with downward-slope on the leeward side. The position of the truck on the road and the value of embankment slope angle that minimizes the rollover coefficient were determined by successfully applying the Response Surface Methodology.

• The Journal of Engineering Research
• /
• v.6 no.1
• /
• pp.83-96
• /
• 2004

A soil mailed wall is adapted as road widening measure and is constructed under a miniature abutment built on steel pipe piles. The soil nailed wall called for removal of the existing embankment slope to permanently retain the fill behind the abutment. The soil nailed wall is fully instrumented and is monitored. A 3D finite element analysis is used to study further the behavior of the soil nailed wall. The complete sequence of construction is simulated. The numerical model is calibrated against the instrumented nailed wall. Then a parametric study is conducted. The results provide valuable information related to the effect of the excavation and nailing on the following: axial load and bending moment in the piles, load in the nails, and wall deflections.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.61 no.2
• /
• pp.13-23
• /
• 2019

In this study, an overtopping model experiments and three dimensional seepage characteristics at the deteriorated homogeneous reservoirs were performed to investigate the behavior of failure for embankment and spillway transitional zone due to overtopping. The failure pattern, pore water pressure, earth pressure and settlement by overtopping were compared and analyzed. The pattern of the failure by overtopping was gradually enlarged towards reservoirs crest from the spillway transition zone at initial stage. In the rapid stage and peak stage, the width and depth of failure gradually increased, and the pattern of the failure appeared irregular and several direction of the erosion. In the early stage, the pore water pressure at spillway transitional zone was more affected as its variation and failure width increased. In the peak stage, the pore water pressure was significantly increased in all locations due to the influence of seepage. The earth pressure increased gradually according to overtopping stage. The pore pressure by the numerical analysis was larger than the experimental value, and the analysis was more likely to increase steadily without any apparent variation. The horizontal and vertical displacements were the largest at the toe of slope and at the top of the dam crest, respectively. The results of this displacement distribution can be applied as a basis for determining the position of reinforcement at the downstream slope and the crest. The collapse in the overtopping stage began with erosion of the most vulnerable parts of the dam crest, and the embankment was completely collapsed as the overtopping stage increased.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.5 no.4
• /
• pp.1-8
• /
• 1985

Stability analysis of the embankment as to water level varation is the most important problem in the safety of the slope because the stress of embankment inside varies as to drawdown of seepage line. Especially when the water level is rapidly drawdown, because the flow direction of the free surface changes the toe of embankment, the factor of safety comes to small, therefore the embankment is dangered. For the purpose of studing these phenomena, the experimental models are built with sand in the laboratory. In the experimental consideration, the falling seepage line and the shape of failure are measured. This paper intends to study the failure slip surface, the relationship between the factor of safety and drawdown velocity, and hydraulic gradient. The results of the experimental study are summarized as follows; 1. Owing to the drawdown of free surface, sliding failure occurred in the upstream fill, the height of failure is 5~10, 9~15, and 13~21(cm) in each model. 2. In consideration of the distribution of pore water pressure Table-5 shows each factor of safety. In the relationship between the drawdown velocity and the factor of factor it's velocity should be limited to 0.21~0.28 (cm/sec), according to each models. In the relationship between the factor of safety and the hydraulic gradient within the upstream slope, it's gradient must be below 0.36~0.43.

• Journal of the Korean Geotechnical Society
• /
• v.37 no.11
• /
• pp.71-81
• /
• 2021

The purpose of this study is liquefaction phenomenon was simulated using the 1g shaking table test. Analysis of liquefaction and Re-liquefaction behavior according to the ground conditions was analyzed when an embankment exists above the ground. The soil used in the experiment was silica sand and the ground composition was a liquefied layer of 50cm (Case 1), a non-liquefied layer of 17.5cm and a liquefied layer of 32.5cm (Case 2). The embankment was formed by fixing the height of 10cm and the slope of the slope at a ratio of 1:1.8. For seismic waves, excitation of a 5Hz sine wave was performed for 8 seconds, and a total of 5 case excitations were performed. In Case 1, it was confirmed that liquefaction occurred at all depths during the first vibration excitation at the free-field and that liquefaction did not occur at all depths except 5cm at the third vibration excitation. At the center of the embankment, liquefaction occurred up to a depth of 20cm during the first vibration excitation, and it was confirmed that liquefaction did not occur at all depths except for a depth of 5cm during the second vibration excitation.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.56 no.6
• /
• pp.63-73
• /
• 2014

In this study, the large scale test was performed to investigate the behavior of failure on the embankment and spillway transitional zone by overtopping. The pore water pressure, earth pressure, settlement and failure behaviors according to several reinforcing method were compared and analyzed. The pore water pressure showed a small change in the spillway transition zone and core, indicating that the riprap and geotextile efficiently reinforced the embankment, but non-reinforcement showed a largely change in pore water pressure. The earth pressure by riprap and geotextile at upstream slope and bottom core increased rapidly with the infiltration of the pore water by overtopping. And the earth pressure at crest showed a smally change due to effect of the inclined core. A settlement by riprap showed a small change and the geotextile decreased a rapidly due to failure of crest. The width of failure by riprap at intermediate stage (50 min) showed a largely due to sliding of crest. But, the width and depth of the seepage erosion after the intermediate overtopping period (100 min) were very small due to the effect of riprap than geotextile and non-reinforcement which delayed failure. It has the effect that protect reservoir embankment from erosion in the central part. The pore water pressure at the spillway transition zone due to overtopping increased a rapidly in the case of non-reinforcement, but the reinforced methods by geotextile and riprap showed a smally change. Therefore, the reinforced method by riprap and geotextile was a very effective method to protect permanently and the emergency an embankment due to overtopping, respectively.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.10 no.4
• /
• pp.95-108
• /
• 2007

Test application of revegetation measure was made on the roadside slope damaged by Nongseo-Eomo national road improvement project in a bid to prevent the soil from being washed out as well as to restore the ecological environment, and the survey for assessment of the effect of slope revegetation measures was conducted, beginning May 11 through Nov 7, 2006. In the wake of comprehensive reviewing and evaluating the surrounding topographic environment, physical and chemical characteristics of soil, germination of revegetation plants, analysis of bio mass, covering ratio and the plants appeared, measure b was found to have been most appropriate to cut blasting rock slope, and alternatively measure c. For cut ripping rock slope, measure c-1 appeared to be effective in revegetation effect, and alternatively, b-1.When it comes to cut soil slope, measure c-2 was found to be effective, and b-2 to be a good alternative. And for embankment soil slope, measure b-3 appeared to be most efficient in revegetation effect and measure f as alternative.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.411-418
• /
• 2009

So far the Limit Equilibrium Method has been widely used by way of 2-D slope stability analysis for the evaluation of land slides and slope failures. However recently the evaluation of 3-D slope stability analysis has been comparatively possible owing to the developments of obtaining the terrain data and geological data and of 3-D slope stability analysis softwares. In Japan the evaluation of the 3-D slope stability analysis has been necessary for the stability analysis of the tunnel mouth. In this study we inspected the economic effects introducing the 3-D slope stability analysis for larger scale landslides and slope failures. In case of 3-D slope stability analysis of landslides we acquired the results that we reduce the cost of the countermeasure work of pile work by 40% comparing the 2-D slope stability analysis. Moreover in case of the stability analysis of slope failures we figured out the results that we reduce the cost of the countermeasure work of anchor works by 20%. Furthermore we proved that 3-D slope stability analysis is effective for the stability analysis of tunnel mouths around the sides of landslides and large scale embankment which we could have not evaluated by conventional 2-D section stability analysis.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.288-298
• /
• 2009

It is well known that the peak strength envelope of geomaterials with no cohesion, such as sand, gravel and rockfill, exhibits significant curvature over a range of stresses. In a practical design of slope, however, the linear Mohr-Coulomb's failure envelope is used as a failure criterion and consequently gives inaccurate safety factors, especially for some ranges of small normal stresses on shallow failure surfaces. Necessity of a nonlinear shear strength envelope in slope stability analysis is on this point. Hence, this study describes how to evaluate nonlinear shear strength of gravel fill materials using the results of large triaxial tests under consolidated-drained condition, and compares the safety factors from slope stability analyses for a homogeneous gravel fill or rockfill embankment incorporating the non-linearity of strength, so as to show its effects on safety factors.