• Elastomers and Composites
• /
• v.42 no.1
• /
• pp.32-46
• /
• 2007

Mechanical properties of rubber material are very important in design procedure to assure the safety and reliability of the rubber components. In this paper, the material test and accelerated heat aging test were carried out. In order to investigate the effects of heat-aging on the material properties, hardness, elongation, stress-strain curves and dynamic characteristics were obtained from various test conditions. Also, rubber material coefficients were determined by both the uniaxical and equi-biaxial tensile tests.

• Fashion & Textile Research Journal
• /
• v.10 no.4
• /
• pp.566-571
• /
• 2008

Frictional sounds of 8 vapor permeable water repellent fabrics by sound generator were recorded and analyzed through FFT fast Fourier transform analysis. The frictional Sounds were quantified by calculating level pressure of total sound(LPT), the level range(${\Delta}L$) and the frequency difference(${\Delta}f$). Mechanical properties were measured by KES-FB. LPT values of specimens finished wet coating were higher than those of other kinds of finishing. ${\Delta}L$ values of specimens laminated were highest. Absolute values of ${\Delta}f$ were high in the cire finished and laminated specimens. Values for bending rigidity, shear stiffness and energy required for the compression of coated specimens increased compared with the cire finished and laminated specimens. Laminated specimens had high values of frictional coefficient and low values of surface roughness. Relationship between frictional sounds and mechanical properties analysed by use of correlation coefficients and stepwise regression. LPT showed significant correlation with elongation, tensile energy, geometrical roughness, weight and thickness. ${\Delta}L$ was highly correlated with tensile linearity, frictional coefficient, and ${\Delta}f$ with tensile linearity, weight and thickness. LPT were revealed to be explained by elongation and weight. ${\Delta}L$were predicted by tensile linearity, and ${\Delta}f$ by tensile linearity and thickness.

• Textile Coloration and Finishing
• /
• v.7 no.4
• /
• pp.25-32
• /
• 1995

This study was carried out to examine the influences of fatigue and perspiration on the deterioration of chrome leather for shoes. The samples were treated with acidic and alkaline artificial perspirations and applied cyclic tensile stress, and the elastic recovery from fatigue strain, tensile strength and elongation, stiffness etc. by regions and directions were determined. The physical properties generally indicate considerable difference by regions and directions due to the thickness, entangling state, and arrangement direction of fiber buldles within the leather. By the treatment of artificial perspirations, the length, weight, strength, elastic recovery from fatigue of the lether are decreased and the thicknes, elongation, and stiffness are increased; and their extents by the alkaline perspiration are higher than those by the acidic one. The elastic recovery from fatigue of samples are decreased with increasing fatigue cylcle; and indicate regressive relations against the logarithm of the elapsed time, and the means of regression coefficients are 2.73 > 2.55 > 2.22 for samples treated by the acidic perspiration, untreated, and treated by the alkaline perspiration, respectively. The tensile strength is decreased and elogation is increased by fatigue, but the changes are diminished likely due to a rearrangment of fiber bundles with increasing fatigue cycle. And the samples become a little flexible immediately after fatigue; but stiffen again with elastic recovery from fatigue strain, consequently for some cases their stiffness after recovery are rather greater than those before fatigre.

• Journal of the Korean GEO-environmental Society
• /
• v.17 no.3
• /
• pp.21-26
• /
• 2016

Soil particle shape analysis was conducted with sands from Jumujun, Korea and Ras Al Khair, Saudi Arabia. Two hundred times enlarged digital images of the particles of those two sands were obtained with an optical microscope. The resolution of the digital images was $640{\times}320$. By conducting digital image processing, the coordinates of the soil particle boundary were extracted. After mapping those coordinates to the complex space, Fourier transformation was performed and the coefficients of each trigonometry term were computed. The coefficients reflect the shape characteristics of the sand grains and are invariant to translation. To evaluate the shape itself excluding the size of the soil particle, the coefficient was normalized by the equivalent radius of soil particle; this is called Fourier descriptor. After analyzing the Fourier descriptors, it was found that the major characteristics of Jumunjin and Ras Al Khair sands were elongation and asymmetry. Furthermore, it was found that the particle shapes reflect the self-similar, fractal nature of the textural features. The effects of resolution on soil particle shape analysis was also studied. Regarding this, it was found that the significant Fourier descriptors were not significantly affected by the image resolution investigated in this study, but the descriptors associated with textural features were affected.

• Elastomers and Composites
• /
• v.55 no.1
• /
• pp.13-19
• /
• 2020

4,4'-Methylenebis(2-chlorobenzenamine) (MOCA)-free fast curing polyurethanes were prepared. In this study, the processibility of a fast curing polyurethane system was characterized by assessing the pot life. The obtained pot life of the polyurethane was 6-8 s, indicating that this prepolymer-curative system is appropriate for ribbon flow casting. The influence of the NCO index on the viscosity and mechanical properties was evaluated. The viscosity, tensile strength, tear strength, and hardness of the as-prepared polyurethanes showed an increasing trend, with an increase in the NCO index, whereas the elongation at break increased initially and then decreased with an increase in the NCO index. The gel fraction and crosslink density showed a direct correlation with the NCO index, which substantiated the improved mechanical properties at the higher NCO index. The coefficients of friction and abrasion deteriorated with an increase in the NCO index.

• Journal of Korea Foundry Society
• /
• v.17 no.4
• /
• pp.365-370
• /
• 1997

The effects of changes in microstructure of Si phase on the thermal expansion coefficients(CTEs) and tensile properties of the hypereutectic Al-Si foundry alloy(A390) were investigated experimentally. Specimens were prepared by various fabrication processes, such as a permanent mold casting, a squeeze casting and a spray casting process, and subsequently hot-extruded. CTEs of the spray-cast specimen were found to be about 10% lower than those of the permanent mold-cast specimen, and the CTEs of the hypereutectic Al-Si alloy(A390) were changed proportionally with the size of Si phase. Ultimate tensile strength of the spray-cast and hot-extruded specimen was dramatically improved about 100% with improved elongation, compared to that of permanent mold-cast specimen. These improvements are mainly attributed to the reduction in size and aspect ratio of the brittle Si phase, and the elimination of the microvoids/porosities formed during casting.

• Land and Housing Review
• /
• v.2 no.1
• /
• pp.69-78
• /
• 2011

The purpose of this research is particle shape evaluation of aggregate using Digital Image Process(DIP). DIP is very useful to measure the roughness and particle shape of aggregates. Couple of aggregates, like standard sand, two different crushed stones, and two different marine aggregates, have been employed. Shape factors of two different marine aggregates are ranged 0.35 to 0.54. Crushed stone I is 0.74 which is highly flat, but standard sand is elongated shape. Especially, two marine aggregate showed a big difference of width and length which meaned a long shape. There is any significant difference of elongation ratio and flatness for each aggregate with different measuring system, like direct measurement of vernier calipers and DIP method. Shape conversion coefficient and equivalent diameter for changing 2D image to 3D image by the Digital Image Process(DIP) have been suggested and modified particle size distribution curve has been showed. The measured flatness ratios of each aggregate were 0.30, 0.36, 0.47 and 0.83, respectively. Also, the conversion shape coefficients of each aggregate were determinded as 0.77, 0.78, 0.84 and 0.92. The size of aggregate has been modified by multiplying the shape conversion coefficient and the aggregate size from DIP. The modified gradation curve with modified volume and weight of aggregate has been suggested. Within the limited test results, DIP is one of useful to get the particle shape of aggregate with limitation of measuring errors and to apply the particle distribution curve.

• Journal of Korea Multimedia Society
• /
• v.11 no.4
• /
• pp.516-524
• /
• 2008

This paper presents a new modeling technique for the simulation of cloth specific characteristics with a set of hard constraints using an implicit constraint enforcement scheme. A conventional explicit Baumgarte constraint stabilization method has several defects. It requires users to pick problem-dependent coefficients to achieve fast convergence and has inherent stabilization limits. The proposed implicit constraint enforcement method is stable with large time steps, does not require problem dependent feed-back parameters, and guarantees the natural physics-based motion of an object. In addition, its computational complexity is the same as the explicit Baumgarte method. This paper describes a formulation of implicit constraint enforcement and provides a constraint error analysis. The modeling technique for complex components of cloth such as seams, buttons, sharp creases, wrinkles, and prevention of excessive elongation are explained. Combined with an adaptive constraint activation scheme, the results using the proposed method show the substantial enhancement of the realism of cloth simulations with a corresponding savings in computational cost.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.39 no.4
• /
• pp.331-338
• /
• 1994

The experiment was conducted to determine if seed size and seed coat color of soybean might be effective in water uptake and cotyledon damage after imbibition, and hypocotyl elongation. Eight soybean cultivars were separated into two classes of large and small seed based on seed weight, and each class included two cultivars with yellow and black seed color, respectively. Small seed size group was superior in water uptake by seed for 24 hour in imbibition at $25^{\circ}C$ , but its differences decreased as soaking time increased. Small seed cultivars germinated faster and had better germination rate than large ones. However, cultivars with black seed coat showed more slow water uptake at initial time and faster germination than yellow seed, but in 24 hour after imbibition, cultivars with black seed coat had higher water uptake rate than yellow seeds. Small seed cultivar group showed no cotyledon damage in imbibition for 24 hour while large seed cultivars were damaged 78% of cotyledon, and black seed showed low cotyledon damage compared to yellow seed. Hypocotyl length was shorter in large seed rather than in small seed, but hypocotyl thickness in large seed was more thick than in small seed. In correlation coefficients, seed coat rate, embryo rate exhibited significantly negative association with seed weight, and the correlation of seed weight with water uptake in 3 hour after soaking was significantly negative, but in 24 hour showed positive correlation.

• Journal of Korea Water Resources Association
• /
• v.54 no.7
• /
• pp.495-507
• /
• 2021

With the recent industrial development, accidental pollution in riverine environments has frequently occurred. It is thus necessary to simulate pollutant transport and dispersion using water quality models for predicting pollutant residence times. In this study, we conducted a field experiment in a meandering reach of the Sum River, South Korea, to validate the field applicability and prediction accuracy of RAMS+ (River Analysis and Modeling System+), which is a two-dimensional (2D) stream flow/water quality analysis program. As a result of the simulation, the flow analysis model HDM-2Di and the water quality analysis model CTM-2D-TX accurately simulated the 2D flow characteristics, and transport and mixing behaviors of the pollutant tracer, respectively. In particular, CTM-2D-TX adequately reproduced the elongation of the pollutant cloud, caused by the storage effect associated with local low-velocity zones. Furthermore, the transport model effectively simulated the secondary flow-driven lateral mixing at the meander bend via 2D dispersion coefficients. We calculated the residence time for the critical concentration, and it was elucidated that the calculated residence times are spatially heterogeneous, even in the channel-width direction. The findings of this study suggest that the 2D water quality model could be the accidental pollution analysis tool more efficient and accurate than one-dimensional models, which cannot produce the 2D information such as the 2D residence time distribution.