• Structural Engineering and Mechanics
• /
• 제26권2호
• /
• pp.127-150
• /
• 2007

The objective of this paper is to develop a finite element procedure for predicting the compressive strength and ultimate axial strain of Carbon Fiber Reinforced Plastics (CFRP) confined circular concrete columns and to study the effective parameters of confinement efficiency for helping design of CFRP retrofit technology. The behavior of concrete confined with CFRP is studied using the nonlinear finite element method. In this paper, effects of column size, CFRP volumetric ratio and plain concrete strength are studied. The confined concrete nonlinear constitutive relation, concrete failure criterion and stiffness reduction methodology after concrete cracking or crushing are adopted. First, the finite element model is verified by comparing the numerical solutions of confined concrete with experimental results. Then the effects of column size, CFRP volumetric ratio and plain concrete strength on the peak strength and ductility of the confined concrete are considered. The results of parametric study indicate that the normalized column axial strength increases with increasing CFRP volumetric ratio, but without size effect for columns with the same CFRP volumetric ratio. As the same, the increase in column ductility depends on CFRP volumetric ratio but without size effect for columns with the same CFRP volumetric ratio.

• 한국생활과학회지
• /
• 제18권6호
• /
• pp.1303-1314
• /
• 2009

The purpose of this study lies in examining the characteristics of differentiated body types for plus-size women and obtaining basic data for the wide-ranging choices of ready-made clothing in a consumer's place. The results of this study displayed no significant differences for subjects in their 30s and 40s in comparison to standards by ages but showed a significant difference with subjects in their 50s when compared with the data from Size Korea (2004). Research data in the height and length categories were lower, and the majority of data from the other categories were higher. In order to analyze the characteristics of a plus-size woman's body, 4 factors were differentiated into 3 types with 17 categories: Factor 1 was the element of the thickness of the trunk, factor 2 was the element of the thickness of the lower body and legs, factor 3 was the element of shoulder size and factor 4 was the element of the upper body length. The accumulation rate was shown to be 74.47%. The characteristics for each type were as follows: Type 1 is a body type with a relatively thin waist, small width and girth of upper body and curvy lower body, type 2 is the average body type, and type 3 is a body type with big breasts and abdominal obesity. The standard body type belonged to type 2. According to the correspondency test between age and type, the characteristics of type 1 corresponded relatively close to the measures of subjects in their 40s and relatively far from subjects in their 30s to 50s while type 2 and type 3 appeared to be similar to subjects in their 50s.

• Biomaterials and Biomechanics in Bioengineering
• /
• 제3권2호
• /
• pp.71-84
• /
• 2016

The finite element method is wide used in simulation in the biomechanical structures, but a lack of studies concerning finite element mesh quality in biomechanics is a reality. The present study intends to analyze the importance of the mesh quality in the finite element model results from humeral structure. A sensitivity analysis of finite element models (FEM) is presented for the humeral bone and cartilage structures. The geometry of bone and cartilage was acquired from CT scan and geometry reconstructed. The study includes 54 models from same bone geometry, with different mesh densities, constructed with tetrahedral linear elements. A finite element simulation representing the glenohumeral-joint reaction force applied on the humerus during $90^{\circ}$ abduction, with external load as the critical condition. Results from the finite element models suggest a mesh with 1.5 mm, 0.8 mm and 0.6 mm as suitable mesh sizes for cortical bone, trabecular bone and humeral cartilage, respectively. Relatively to the higher minimum principal strains are located at the proximal humerus diaphysis, and its highest value is found at the trabecular bone neck. The present study indicates the minimum mesh size in the finite element analyses in humeral structure. The cortical and trabecular bone, as well as cartilage, may not be correctly represented by meshes of the same size. The strain results presented the critical regions during the $90^{\circ}$ abduction.

• 한국해안해양공학회지
• /
• 제14권1호
• /
• pp.86-93
• /
• 2002

항만부진등 해석에 사용되는 유한요소의 적정 크기를 검토하기 위해 완전개방 직사각형 항만에 대해서 다양한 크기의 요소를 사용한 수치실험을 실시하였다. 수치실험 결과, 공진주기와 증폭비의 허용 오차율을 모두 2%로 하는 경우 파장당 9개, 1%로 하는 경우 12개의 요소가 필요한 것으로 나타났다. 또한, 요소 수의 증가에 따라 공진주기의 오차율은 선형적으로, 증폭비의 오차는 진동하면서 감소하였으며, 요소 수를 9개보다 적게 하는 경우 증폭비의 오차가 상대적으로 크게 증가하였다

• 소성∙가공
• /
• 제9권4호
• /
• pp.379-388
• /
• 2000

This study aims to examine the influence of experimental and numerical factors on the results of the test and finite element simulation to evaluate the formability of sheet metals. The stretch-forming test with a hemispherical punch is carried out to obtain the limiting dome height (LDH) and forming limit diagram (FLD) for several kinds of aluminium and steel sheet. The results of the LDH and FLD tests are analysed to find any correlation with the uniaxial tensile properties. It proves that the size of the prescribed grid has great influence on the measured value of strain. The finite element analysis of the punch stretching process is also carried out and the result is compared with the experimental data. The influence of the numerical parameters such as friction coefficient, element size and anisotropy model on the simulation results tms out to be very considerable.

• 소성∙가공
• /
• 제13권2호
• /
• pp.115-121
• /
• 2004

Hemming is the last farming process in stamping and determines external quality of automotive outer panels. Few numerical approaches using 3-dimensional finite element model have been applied to a hemming process due to small element size which is needed to express the bending behavior of the sheet around small die comer and comparatively big model size of automotive opening parts, such as side door, back door and trunk lid etc In this study, part model assembling method is suggested and applied to the 3-dimensional finite element simulation of flanging and hemming process far an automotive front hood.

• Journal of electromagnetic engineering and science
• /
• 제5권3호
• /
• pp.122-125
• /
• 2005

This paper describes a design of a miniature patch antenna and its 4-channle array for 5.25 GHz wireless LAN band. Each patch element is designed for the low mutual coupling between each element and for the small size of the array antenna. The size of the each element is $7 mm{\times}14.5 mm{\times}5.6 mm$ and it satisfy IEEE 802.11a frequency band. It is arrayed for independent 4-channel operation. The total size of the array antenna is $35.6 mm{\times}52.5 mm{\times}5.6 mm$. The measured reflection coefficients and the radiation patterns of the fabricated antennas show the reasonable agreements with prediction.

• 소성∙가공
• /
• 제13권3호
• /
• pp.248-252
• /
• 2004

The mechanical properties of polycrystalline thin-films, critical for Micro-Electro-Mechanical Systems (MEMS) components, are known to have the size effect and the scatter in the length scale of microns by the numbers of intensive investigation by experiments and simulations. So, the consideration of the microstructure is essential to cover these length scale effects. The lattice based stochastic model for the microstructure evolution is used to simulate the actual microstructure, and the fast and reliable algorithm is described in this paper. The kinetics parameters, which are the key parameters for the microstructure evolution based on the nucleation and growth mechanism, are extracted from the given micrograph of a polycrystalline material by an inverse method. And the method is verified by the comparison of the quantitative measures, the number of grains and the grain size distribution, for the actual and simulated microstructures. Finite element mesh is then generated on this lattice based microstructure by the developed code. And the statistical finite element analysis is accomplished for selected microstructure.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2003년도 종합학술발표회 논문집 Vol.13 No.1
• /
• pp.473-477
• /
• 2003

In this paper, a integrated structure of a two-element microstrip patch antenna with two feeds for GPS/PCS dual-band operation is proposed. The radiating element for PCS operation is a novel broad band low-profile cylindrical monopole top-loaded with a shorted meander patch, which gives linearly polarized conical radiation pattern and size reduction of patch due to meander line. The radiating element for GPS operation is a novel square-ring microstrip patch with truncated corners and slits. which provide circularly polarized broadside radiation patterns and size reduction due to slots. using dielectric substrate in GPS antenna of proposed antenna provide to improve isolation between two feeds and reduce size of patch. The proposed antenna achieves the bandwidth and polarization requirements of GPS and PCS systems.

• Journal of Mechanical Science and Technology
• /
• 제20권5호
• /
• pp.621-633
• /
• 2006

To reflect the size effect of material $(1\sim15{\mu}m)$ during plastic deformation of polycrystalline copper, a constitutive equation which includes the strain gradient plasticity theory and intrinsic material length model is coupled with the finite element analysis and applied to plane strain deformation problem. The method of least square has been used to calculate the strain gradient at each element during deformation and the effect of distributed force on the strain gradient is investigated as well. It shows when material size is less than the intrinsic material length $(1.54{\mu}m)$, its deformation behavior is quite different compared with that computed from the conventional plasticity. The generation of strain gradient is greatly suppressed, but it appears again as the material size increases. Results also reveal that the strain gradient leads to deformation hardening. The distributed force plays a role to amplify the strain gradient distribution.