• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.111-114
• /
• 2003

In order to improve the surface uniformity and the conduction properties of the fabricated YBCO thick films, a system that applies alternating field vertically to the EPD field has been developed for the first time and applied to the electrophoretic deposition process. The applied alternating electric field caused a force to be exerted on each YBCO particle and resulted in a shaking of the particle in the direction of applied electric field, accomplishing a uniform particle orientation. The usual commercial electrical power was used for the vertically applied alternating voltage and the induced electric field was 25-120 V/cm at 60Hz. The thick film fabricated by the method developed in this paper showed better surface uniformity without crack and porosity and improved film characteristics such as critical temperature ($T_{c,zero}$ : 90 K) and critical current density ($2354\;A/cm^2$). Therefore, it is expected that the shaky-aligned electrophoretic deposition method can be used to fabricate superconductor films through a simpler process and at less expense.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.575-579
• /
• 2005

A beautiful, flexible active-matrix electrophoretic display (AM-EPD) device is reported. The flexible AM-EPD device has a $40.0{\times}30.0\;mm^2$ display area, measures about 0.27 mm in thickness, weighs about 0.45 g and possesses only 20 external connections. The flexible AM-EPD device displays clear black-and-white images with 5 gray-scales on $160{\times}120$ pixels. The display is free from residual image problems, because we use an area-gray-scale method on $320{\times}240$ EPD elements, each of which is driven with binary signals. Each pixel consists of 4 EPD elements. In addition, since the response time of the electrophoretic material is as long as approximately 400 ms and since the display possesses a large number of EPD elements, we have developed a special driving method suitable for changing EPD images comfortably. A complete image is formed on the AM-EPD device, consisting of a reset frame and several, typically 6, image frames.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.5C
• /
• pp.217-228
• /
• 2009

In case of application of electrophoresis method for leakage restoration of waste impoundment, main points of consideration were to evaluate the mobility of clay particles by electrophoretic force and capacity of leakage repair in leachate electrolyte system contained with various chemical species. However, the flocculation phenomena of clay particles induced by electrochemical interaction between various chemical species and clay particles would cause the big problems in electrophoresis method. Therefore, a series of laboratory tests such as one-dimensional electrophoresis and gravitational experiments were carried out in order to identify the specific chemical species affected flocculation of clay particles and the range of chemical concentration in leachate. In addition, the characteristics of clay particle behavior with chemical species and concentration range in leachate were analized using the concept of the settling velocity, zeta potential, and electrophoretic velocity.

• Proceedings of the Korean Society of Fisheries Technology Conference
• /
• 1998.06a
• /
• pp.255.2-257
• /
• 1998

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.250-254
• /
• 2000

High temperature superconducting films deposited on metal Ag wire were prepared with YBCO powders by electrophoretic deposition method. $I_2$was used as additives for surface charge of YBCO particles. When 2~3 wt.% $BaF_2$ was added in the YBCO suspension, the pores and cracks of film surface were decreased and film density could be increased. In case of YBCO films, the critical current density ($J_{c}$) was calculated at the value of $1458{\;}A/\textrm{cm}^2$ (77K, 0K) by 4 point prove method.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.5
• /
• pp.386-392
• /
• 2020

In this study, the drift current characteristics of charged particles are analyzed for panels fabricated by varying the waveform biasing of the active particle loading method (APLM), which is a method driven by the electrophoretic principle of loading charged particles into a cell of a barrier rib-type electronic paper. We prepare 3 panels using APLM and 1 panel without APLM. The waveform of APLM uses square wave and ramp wave, and the step voltage wave is applied to the driving voltage. The drift currents measured from the square wave and ramp wave with the same period applied by APLM are 4.872 µC and 5.464 µC, respectively, and the ramp wave is shown to be relatively advantageous for loading charged particles that have a large q/m. The time-current curve results confirm that the abrupt movement of charged particles is occurring. When the step form wave signal with a short time of 1s is first applied, initial large movement of the charged particles is confirmed to occur in all samples, which is understood as the effect of applying the voltage necessary to remove the imaging force. The results of this study are expected to improve the loading of charged particles into the electronic paper cell, driven by the electrophoretic principle and optimization of the driving conditions.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.27 no.2
• /
• pp.125-131
• /
• 1991

Electrolyte matrix fabrication process can be classifed as hot pressing, tape casting, callendering, electrophoretic deposition. however, these have limits in practice. Hot pressing is cumbersome method, because of careful heating and cooling. Furthermore, the perfected tile is so fragile that it is difficult to fit in a cell. Therefore this method is not adequate for mass production of the electrolyte matrix. Using electrophoretic deposition method, a very thin matrix can be made, but many attempts of the electrolyte embeding were found to be failure. Tape casting and callendering methods are employed in most of the matrix fabrication for the present. But these methods require lots of water as a solvent, so that coating of the LiAlO sub(2) with electrolyte is difficult. Recently, hot roll milling method has been developed and the perfected matrix was proved to be free from crack. The method, however, needs a roller to make a matrix and a perfected matrix is carefully striped off from the cooled roller. Therefore, this method requires a long time due to the cooling process. The author proposes a cold rolling process. On this method, heated slurry of the LiAlO sub(2) mixed with binder, is rolled with a cold roller. The heated slurry dose not adhere to the roller, since contacted hot slurry is rapidly solidified. Therefore fabrication speed is increased, without getting rid of merits of the hot rolling process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.714-718
• /
• 2003

Usually for the commercial preparation of barium titanate films or ceramics the reaction atmosphere must be preferably in air. However, normally air is not used because it contains carbon dioxide, which can easily react with barium to form the undesired product barium carbonate, leading to unwanted second-phase formation in the (mal stages of the process. In the present work a series of perovskite barium titanate films was prepared by the sol-gel method, using a metal alkoxide solutions in the electrophoretic deposition (EPD). The influence of several process parameters, like sintering temperature of sol preparation before EPD and heat-treatment temperature and non-oxidized atmosphere, on the film properties is described.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1728-1731
• /
• 1996

To develop more sensitive humidity sensor on high temperature region, in this paper, we prepared polyimide humidity sensor by electrophoretic method. Sensing properties of be sensor in high temprature region were studied and compared with that prepared by solution casting method. From the result, the thiner film thickness, the more sensitive. however, It is difficult to make he thickness optimal because of short between electrodes, and the thickness of upper electrode is one of most important parameters affecting pefomance of the sensor.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1642-1644
• /
• 1996

Passivation must prevent ionic charge movement on the surface of the junction, thereby minimizing the junction leakage and maximizing the breakdown voltage of the devices. Borosilicate glasses are widely used as surface passivants for such silicon power devices as thyristors, transistor, and diodes. Since these 91asses are electrically stable at high temperatures and in high electric fields, they can readily be applied as a thick film, and they are resistant to humidity and have low ionic mobility. A deposition technique of glass film on the silicon surface by electrophoresis in which acetone is used as a suspension medium has been investigated. The purpose of this paper is to describe electrophoretic deposition method for glass passivation and characteristics of glass films which were compared using DTA, SEM, XRD, as a function of firing temperature.