• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.112.1-112.1
• /
• 2011

The back contact solar cell (BCSC) has several advantages compared to the conventional solar cell since it can reduce grid shadowing loss and contact resistance between the electrode and the silicon substrate. This paper presents the effect of the surface texturing of the silicon BCSC by varying the texturing depth or the texturing gap in the commercially available simulation software, ATHENA and ATLAS of the company SILVACO. The texturing depth was varied from $5{\mu}m$ to $150{\mu}m$ and the texturing gap was varied from $1{\mu}m$ to $100{\mu}m$ in the simulation. The resulting efficiency of the silicon BCSC was evaluated depending on the texturing condition. The quantum efficiency and the I-V curve of the designed silicon BCSC was also obtained for the analysis since they are closely related with the solar cell efficiency. Other parameters of the simulated silicon BCSC are as follows. The substrate was an n-type silicon, which was doped with phosphorous at $6{\times}10^{15}cm^{-3}$, and its thickness was $180{\mu}m$, a typical thickness of commercial solar cell substrate thickness. The back surface field (BSF) was $1{\times}10^{20}\;cm^{-3}$ and the doping concentration of a boron doped emitter was $8.5{\times}10^{19}\;cm^{-3}$. The pitch of the silicon BCSC was $1250{\mu}m$ and the anti-reflection coating (ARC) SiN thickness was $0.079{\mu}m$. It was assumed that the texturing was anisotropic etching of crystalline silicon, resulting in texturing angle of 54.7 degrees. The best efficiency was 25.6264% when texturing depth was $50{\mu}m$ with zero texturing gap in case of low texturing depth (< $100{\mu}m$).

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2006년도 춘계종합학술대회
• /
• pp.1023-1026
• /
• 2006

가정이나 병원 등 해상에서 위급한 환자를 모니터링 할 때 현재의 심전도 측정기의 전극센서가 불편할 경우가 많다. 구급차량 내에서나 선박에서 환자를 측정시 흔들림이 심하기 때문에 전극이 떨어져 측정이 쉽지가 않으며 또 환자의 몸에 지방분이나 습기가 많을 경우를 쉽게 붙어있지 않아 측정이 더욱 힘들어진다. 본 연구에서는 환자가 언제든지 전극을 붙이고 화장실이나 외출까지도 자유롭게 할 수가 있도록 하였으며 또 흉부에 쉽게 착용이 용이하도록 부드러운 벤드 형태로 설계되었다. 심전도의 전극소재로는 전기저항특성이 우수하고 피부 트러블이 거의 없는 금을 소재로 한 제품을 적용하였으며 광전용적맥파 및 말초체온 등을 추가로 설계하여 다중생체신호를 모니터링 할 수 있도록 구현하였다. 본 실험에서는 가승이나 늑골부위에서는 생체신호전달이 좋았으며, 환자의 복부부위에서는 생체신호가 아주 작게 검출되었다. 전극소재로 금 전극을 사용하여 일반적인 전극을 이용할 때 보다 신호 검출이 우수하다는 결과를 얻었으며. 일반적인 전극은 단순1회용으로 끝나지만 금 전극센서는 반영구적이면서도 환자가 이동시 접촉력이 우수하여 보다 정확한 데이터를 얻을 수가 있었다.

• 센서학회지
• /
• 제21권6호
• /
• pp.425-428
• /
• 2012

This paper presents the fabrication and characterization of graphene based hydrogen sensors. Graphene was synthesized by annealing process of Ni/3C-SiC thin films. Graphene was transferred onto oxidized Si substrates for fabrication of chemiresistive type hydrogen sensors. Au electrode on the graphene shows ohmic contact and the resistance is changed with hydrogen concentration. Nanoparticle catalysts of Pd and Pt were decorated. Response factor and response (recovery) time of hydrogen sensors based on the graphene are improved with catalysts. The response factors of pure graphene, Pt and Pd doped graphenes are 0.28, 0.6 and 1.26, respectively, at 50 ppm hydrogen concentration.

• 통합자연과학논문집
• /
• 제2권1호
• /
• pp.13-17
• /
• 2009

A newly developed OTFT manufacturing process using the combination of self-assembly techniques and vapor phase polymerization method revealed that a thick $SiO_2$ dielectric layer (100~200 nm) is not well compatible with conducting polymer electrode, thereby resulting in still recognizable contact resistance, unstable $V_{th}$ and leaking off current. A couple of very recent studies showed that this issue may be solved by replacing such inorganic dielectric with a self-assembled monolayer or multilayer (organic) dielectric. Therefore, this short review introduces recent trends in the development of high performance thin film transistor consisting of both organic semiconductor and SAM dielectric.

• 한국고분자학회:학술대회논문집
• /
• 한국고분자학회 2006년도 IUPAC International Symposium on Advanced Polymers for Emerging Technologies
• /
• pp.63-64
• /
• 2006

The solid state dye-sensitized solar cells (DSSCs) employing polymer electrolytes show high overall energy conversion efficiency as high as 4.5 % at 1 sun conditions. The improved efficiency may be primarily due to the enlarged interfacial contact area between the electrolyte and dyes in addition to the increased ionic conductivity, which were done by utilizing liquid oligomers, followed by in situ self-solidification, to form the solid DSSCs: "Oligomer Approach". The effect of the charge transfer resistance at the counter electrode side on the efficiency has also been investigated.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.456-461
• /
• 2003

A fuel cell is an electrochemical device in which the energy of a chemical reaction is converted directly into electricity. By combining hydrogen fuel with oxygen from air, electricity is formed, without combustion of any form. Water and heat are the only by-products when hydrogen is used as the fuel source. Fuel cell stack consists of multi-layered unit cells. A unit cell consists of MEA and bipolar plates. The end plate of fuel cell stack should give a uniform distributed pressure to multi unit cell layers so as to reduce the contact resistance and to prevent the leakage of reactant gases and the damage of multi layer components. The current end plate is redundantly large and heavy. It makes the power per unit volume reduced. Topology optimization of end plate is conducted for mass reduction and enhancement of bending rigidity. The evaluation of the current design and the recommendation for the future design is remarked.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 B
• /
• pp.406-408
• /
• 1997

This paper presents the new method of a nondestructive spot welding state inspection system using neural networks. The learning process of neural networks makes the inspection system to adapt the variable welding parameters. The inspecting process is working with on-line real-time after off-line learning process. This neural network based inspection system shows reliable results through the field test for variations of applied voltages, currents, and contact area of the welding electrode.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.916-917
• /
• 2006

Solid Oxide Fuel Cell technology uses powder processes to produce electrodes with residual porosity by partially sintering a mixture of electronically and ionically conducting particles. We model porous fuel cell electrodes with 3D packings of monosized spherical particles. These packings are created by numerical sintering. Each particle-particle contact is characteristic for an ionic, electronic or electrochemical resistance. The numerical packing is then discretized into a resistor network which is solved by using Kirchhoff's current law to evaluate the electrode's electrochemical performance. We investigate in particular percolation effects in functionally graded electrodes as compared to other types of electrodes.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.1365-1367
• /
• 2003

In this paper, element technologies such as soldering. arrangement and lamination processes for photovoltaic module manufacture were examined and described as main processes. Especially solder paste and temperature condition in soldering process, loss factor in arrangement process and process conditions in lamination process are investigated to minimize the electrical loss. As a results, temperature condition in soldering process was found to be critical to contact resistance of electrode and life-time. Productivity of the process decreases dramatically by physical damage during arrangement process. Pressure level and press condition of upper chamber in lamination process were important parameters for the reliability. According to the test result of photovoltaic module, electrical properties dropped about $5{\sim}25%$ after 5 years.

• 센서학회지
• /
• 제22권3호
• /
• pp.197-201
• /
• 2013

This paper describes the fabrication and characterization of graphene based carbon dioxide ($CO_2$) gas sensors. Graphene was synthesized by thermal decomposition of SiC. The resistivity $CO_2$ gas sensors were fabricated by pure graphene and graphene decorated Au nanoparticles (NPs). The Au NPs with size of 10 nm were decorated on graphene. Au electrode deposited on the graphene showed Ohmic contact and the sensors resistance changed following to various $CO_2$ concentrations. Resulting in resistance sensor using pure graphene can detect minimum of 100 ppm $CO_2$ concentration at $50^{\circ}C$, whereas Au/graphene can detect minimum 2 ppm $CO_2$ concentration at same at $50^{\circ}C$. Moreover, Au NPs catalyst improved the sensitivity of the graphene based $CO_2$ sensors. The responses of pure graphene and Au/graphene are 0.04% and 0.24%, respectively, at $50^{\circ}C$ with 500 ppm $CO_2$ concentration. The optimum working temperature of $CO_2$ sensors is at $75^{\circ}C$.