• 한국근적외분광분석학회:학술대회논문집
• /
• 한국근적외분광분석학회 2001년도 NIR-2001
• /
• pp.1527-1527
• /
• 2001

Glucose, fructose and sucrose being the main sugars that can be found in natural fruit juice. Many instrumental methods, such as GC, LC, electrochemical or spectrometric methods provide information about both the total content of sugars and the specific concentration of each carbohydrate[1]. The simplicity of sample handling and measurement in the near IR(NIR) wavelength region, which allows the use of long pathlength, optical glass cells and optical fibers, makes NIR a good alternative for sugar determination [2]. In the present study, six varieties of persian grapes were harvested at intervals through august to october and analysed for sugars by NIR. The results were processed by principal component regression (PCR) and partial least squares (PLS) analysis. Sample juice was prepared by squeezing through gauze from crashed grape. This solution was treated by zinc ferrocyanide prior to analysis in order to eliminate colored compounds and all optically active nonsugar substances. For glucose and fructose the most characteristic wavelengths were 1456nm corresponding to the first harmonic O-H stretching and the second at 2062nm corresponding to O-H stretching and deformation; secondary characteristic combination bands were also seen at 2265 nm (O-H and C-C stretching) and at 2240 nm (C-H and C-C stretching). However these spectra were taken over a wavelength range from 1100-2500nm at room temperature of 25-$30^{\circ}C$. To test the accuracy of the described procedure, samples of six varieties of grape were analysed by the proposed NIR and a standard method[2]. Good agreement were found between these two sets of the results. To perform the recovery studies , samples of grape juices previously analysed by the proposed method, were spiked with known amounts of each individual sugars and then analysed again. Relative standard deviations varied from 1.4 to 1.8% for six independent measurements of individual and total sugar concentration. In the analysis of real and synthetic samples, precise and accurate results were obtained , providing accuracy errors lower than 1.9% in all cases. Average recoveries of ${97}{\pm}{4%}$ for total sugar and between ${95}{\pm}{5%}$ and ${99}{\pm}{2%}$ for sing1e sugars demonstrate the applicability of the methodology developed to the direct analysis of grape Juice.

• The Korean Journal of Ceramics
• /
• 제4권2호
• /
• pp.95-98
• /
• 1998

We have developed new type of superconducting-superionic conducting nanohybrids, $Ag_xI_wBi_2Sr_2Ca_{n-1}Cu_nO_y$ (n=1 and 2) by applying the chimie douce reaction to the superconducting Bi-based cuprates. These nanohybrids can be achieved by the stepwise intercalation whereby the $Ag^+$ ion is thermally diffused into the pre-intercalated iodine sublattice of $IBi_2Sr_2Ca_{n-1}Cu_nO_y$. According to the X-ray diffraction analysis, the Ag-I intercalates are found to have an unique heterostructure in which the superionic conducting Ag-I layer and the superconducting $IBi_2Sr_2Ca_{n-1}Cu_nO_y$ layer are regularly interstratified with a remarkable basal increment of ~7.3$\AA$. The systematic XAS studies demonstrate that the intercalation of Ag-I accompanies the charge transfer between host and guest, giving rise to a change in hole concentration of $CuO_2$ layer and to a slight $T_c$ change. The Ag K-edge EXAFS result reveals that the intercalated Ag-I has a $\beta$-AgI-like local structure with distorted tetrahedral symmetry, suggesting a mobile environment for the intercalated $Ag^+$ ion. In fact, from ac impedance analyses, we have found that the Ag-I intercalates possess a fast ionic conductivity ($\sigma_i=10^{-1.4}\sim 10^{-2.6}\Omega^{-1}\textrm{cm}^{-1}\;at\;270^{\circ}C$ with an uniform activation energy ($\DeltaE_a=0.22\pm 0.02$ eV). More interesting finding is that these intercalates exhibit high electronic conducting as well as ionic ones ($t_i$=0.02~0.60) due to their interstratified structure consisting of superionic conducting and superconducting layers. In this respect, these new intercalates are expected to be useful as an electrode material in various electrochemical devices.

• 분석과학
• /
• 제6권5호
• /
• pp.417-424
• /
• 1993

5,7-디클로로-8-히드록시퀴놀리놀(Hdcq)과 2-메르캅토피리미딘(Hmpd)를 포함하는 8-배위 테트라키스 몰리브데늄(IV) 착물을 합성하였다. $Mo(mpd)_4$, $Mo(dcq)(mpd)_3$, $Mo(dcq)_2(mpd)_2$, $Mo(dcq)_3(mpd)$와 $Mo(dcq)_4$ 착물들을 TLC plate에서 분리하였다. 이 착물들의 특성을 $^1H-nmr$ 스펙트럼과 자외선-가시광선 스펙트럼으로 조사하였다. 리간드의 질소원자에 대한 ${\alpha}$위치 양성자의 화학적 이동값은 낮은 장으로 이동되었으며, $Mo(dcq)(mpd)_3$와 $Mo(dcq)_3(mpd)$는 같은 위치의 양성자가 2:1의 상대적 세기로 나타났고 $Mo(dcq)_2(mpd)_2$는 거의 같은 세기였다. 이들 착물의 입체화학을 nmr 스펙트럼과 Orgel 규칙으로 고찰했다. 이 착물들의 전자전이 스펙트럼은 세기(${\varepsilon}$>10,000~25,000)와 낮은 에너지($16,600{\sim}19,800cm^{-1}$) 흡수띠를 관찰하여 이를 전하이동 흡수띠로 해석하였다.

• 한국재료학회지
• /
• 제21권1호
• /
• pp.1-7
• /
• 2011

Methods of producing hydrogen include steam reforming, electrochemical decomposition of water, and the SI process. Among these methods, the Sulfur iodine process is one of the most promising processes for hydrogen production. The thermochemical sulfur-iodine (SI) process uses heat from a high-temperature-gas nuclear reactor to produce $H_2$ gas; this process is known for its production of clean energy as it does not emit $CO_2$ from water. But the SI-process takes place in an extremely corrosive environment for the materials. To endure SI environments, the materials for the SI environment will have to have strong corrosion resistance. This work studies the corrosion resistances of the Fe-Si, Ni-Ti and Ni Alloys, which are tested in SI-process environments. Among the SI-process environments, the conditions of boiling sulfuric acid and decomposed sulfuric acid are selected in this study. Before testing in boiling sulfuric acid environments, the specimens of Fe-4.5Si, Fe-6Si, Ni-4.5Si, Ni-Ti-Si-Nb and Ni-Ti-Si-Nb-B are previously given heat treatment at $1000^{\circ}C$ for 48 hrs. The reason for this heat treatment is that those specimens have a passive film on the surface. The specimens are immersed for 3~14 days in 98wt% boiling sulfuric acid. Corrosion rates are measured by using the weight change after immersion. The corrosion rates of the Fe-6Si and Ni-Ti-Si-Nb-B are found to decrease as the time passes. The corrosion rates of Fe-6si and Ni-Ti-Si-Nb-B are measured at 0.056 mm/yr and 0.16 mm/yr, respectively. Hastelloy-X, Alloy 617, Alloy 800H and Haynes 230 are tested in the decomposed sulfuric acid for one day. Alloy 800H was found to show the best corrosion resistance among the materials. The corrosion rate of Alloy 800H is measured at -0.35 mm/yr. In these results, the corrosion resistance of materials depends on the stability of the oxide film formed on the surface. After testing in boiling sulfuric acid and in decomposed sulfuric acid environments, the surfaces and compositions of specimens are analyzed by SEM and EDX.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.250-254
• /
• 2002

Intergranular corrosion of austenitic stainless steels is a conventional and momentous problem during welding and high temperature use. One of the major reasons for such intergranular corrosion is so-called sensitization, i.e., chromium depletion due to chromium carbide precipitation at grain boundaries. Conventional methods for preventing sensitization of austenitic stainless steels include reduction of carbon content in the material, stabilization of carbon atoms as non-chromium carbides by the addition of titanium, niobium or zirconium, local solution-heat-treatment by laser beam, etc. These methods, however, are not without drawbacks. Recent grain boundary structure studies have demonstrated that grain boundary phenomena strongly depend on the crystallographic nature and atomic structure of the grain boundary, and that grain boundaries with coincidence site lattices are immune to intergranular corrosion. The concept of "grain boundary design and control", which involves a desirable grain boundary character distribution, has been developed as grain boundary engineering. The feasibility of grain boundary engineering has been demonstrated mainly by thermomechanical treatments. In the present study, a thermomechanical treatment was tried to improve the resistance to the sensitization by grain boundary engineering. A type 304 austenitic stainless steel was pre-strained and heat-treated, and then sensitized, varying the parameters (pre-strain, temperature, time, etc.) during the thermomechanical treatment. The grain boundary character distribution was examined by orientation imaging microscopy. The intergranular corrosion resistance was evaluated by electrochemical potentiokinetic reactivation and ferric sulfate-sulfuric acid tests. The sensitivity to intergranular corrosion was reduced by the thermomechanical treatment and indicated a minimum at a small roll-reduction. The frequency of coincidence-site-lattice boundaries indicated a maximum at a small strain. The ferric sulfate-sulfuric acid test showed much smaller corrosion rate in the thermomechanically-treated specimen than in the base material. An excellent intergranular corrosion resistance was obtained by a small strain annealing at a relatively low temperature for long time. The optimum parameters created a uniform distribution of a high frequency of coincidence site lattice boundaries in the specimen where corrosive random boundaries were isolated. The results suggest that the thermomechanical treatment can introduce low energy segments in the grain boundary network by annealing twins and can arrest the percolation of intergranular corrosion from the surface.

• 대한화학회지
• /
• 제30권1호
• /
• pp.19-26
• /
• 1986

공기산화와 수증기 산화법에 의하여 Ti$O_{2-x}$박막을 만들었고, 알곤 기체속에서 $TiO_2$단결정을 환원하였다. Ti$O_{2x}박막의 전극 특성은 환원된 단결정 rutile의 특성과 거의 같았다. 산소가 용해된 전해질용액에서 측정된 Ti$O_{2-x}$전극들의 전류-전압 곡선으로 부터 음극전류의 peak는 -0.8V ~ -1.0V에서 나타났으며, 영볼트 근처의 Ti$O_{2-x}$전극들의 음극전류는 공기로 포화된 용액에서 보다 질소로 포화된 용액에서 더 크게 나타났다. 시간에 따르는 전류 (i)의 변화는 $i_0e^{-kt}$식에 의존하였고 이때의 속도상수(k)는 $k_0{[H^+]}^nexp(A{\eta}+\frac{E_a}{RT})$로 나타낼 수 있었다. 여기서 활성화에너지 Ea는 0.035~0.145V의 과전압에서는 4.6~4.8kcal/mole, 0.2~0.5V의 과전압에서는 1.6kcal/mole이고, 위식중의 n과 A는 0.035~0.145V에서 0.1과, 5.4~5.6/V, 0.2~0.5V에서는 0.04와 1.3/V이었다. 산소의 환원반응은 전체적으로 비가역 반응임을 알았다.

• 대한화학회지
• /
• 제41권11호
• /
• pp.594-599
• /
• 1997

RF 스피터링법을 써서 $Li_{2x}Ni_{1-x}O$ 박막을 제조하였으며, 그 과정에서 기판의 온도$(50/230^{\circ}C)와$ 분위기 $(Ar/O_2)$를 변수로써 막의 미세구조를 조절하였다. 투과전자현미경을 이용한 막 구조 분석에 의해 낮은 기판 온도와 $O_2$ 조건에서 막의 조성입자가 작아짐을 관찰하였고, $50^{\circ}C/O_2$ 하에서 얻이진 $Li_{2x}Ni_{1-x}O$ 박막은 약 $80\AA$ 크기의 입자로 이루어져 있었다. 전기화학적 조건 하에서 $Li_{2x}Ni_{1-x}O$ 박막의 변색현상을 조사한 결과, 박막의 미세구조 발달에 의해 $Li^+$ 이온의 가역적 수용량이 증가하고, 결과적으로 전기변색 기능이 향상됨을 알 수 있엇다. 50 $^{\circ}C/O_2$ 하에서 얻어진 170 nm 두께의 $Li_{2x}Ni_{1-x}O$ 박막은 30 mC/$cm^2$의 $Li^+$ 이온 수용력과 함께 약 1.3의 흡광밀도(OD)를 나타내었다.

• 한국환경보건학회지
• /
• 제45권6호
• /
• pp.646-657
• /
• 2019

Objectives: The purpose of this study was to suggest methods to investigate continuous monitoring of concentration levels and assess the exposure of individuals considering the actual time activity of residents for formaldehyde and particulate matter (PM₁₀, PM_2.5) in the indoor and outdoor air of a house, assess the health risks of children and adults based on the results of the exposure assessment, and provide basic data on studies for assessing exposure and health risks in Korea in the future. Methods: The concentration levels of formaldehyde and particulate matter were measured in a family home in Gyeonggi-do Province from April 25 to July 31, 2019, using electrochemical sensors (formaldehyde) and light scattering sensors (PM₁₀, PM_2.5). Risk assessment by the duration of exposure by time activity was performed by dividing between weekdays and weekends, and indoors and outdoors. Results: The greatest level of carcinogenic risk from inhaling formaldehyde was indoors during the weekdays for both children and adults. For children, the risk was at 7.5 per approximately 10,000 people, and for adults, the risk was at 4.1 per approximately 10,000 people. PM₁₀ and PM_2.5 also showed the greatest values indoors during the weekdays, with children at 1.7 people and 1.4 per approximately 100 people, respectively, and adults at 8.2 per approximately 1,000 and 1.8 per approximately 100 people, respectively. Conclusions: The risks of formaldehyde, PM₁₀ and PM_2.5 were shown to be high indoors. Therefore, consideration of exposure assesment for each indoor pollutant and management of indoor air quality is necessary.

• 대한화학회지
• /
• 제31권6호
• /
• pp.542-554
• /
• 1987

네자리 schiff base cobalt(II) 착물로서 Co(SED), Co(SND) and Co(SOPD)들을 합성하여 이들 착물들의 DMSO 용액에서 산소를 가하여 산소첨가 생성착물로 $[Co(SED)(DMSO)]_2O_2,\;[Co(SND)(DMSO)]_2O_2$ 및 $[Co(SOPD)(DMSO)]_2O_2$들을 합성하였다. 이들의 원소분석과 Cobalt정량, IR-Spectra, T.G.A. 및 자화율을 측정하여 산소:cobalt(II) 착물의 결합비가 1:2이고 네자리 schiff base cobalt(II)와 DMSO 및 산소가 6배위 결합으로 주어짐을 알았으며 Co(SED), Co(SND) 및 Co(SOPD) 착물들의 0.1M TEAP-DMSO용액에서 순환전압-전류법에 의한 산화 환원 과정이 Co(SED) 및 Co(SOPD)는 Co(II) / Co(III)와 Co(II) / Co(I) 과정이 가역적으로 일어나고 Co(SND)는 Co(II) / Co(III)과정은 가역적이지만 Co(II) / Co(I) 과정은 비가역적이다. 또한 산소 첨가 생성물의 착물들은 0.1M TEAP-DMSO 용액에서 산소결합의 환원과정이 $E_{pc}$ = -0.80~-0.89V에서 일어나고 이에 Couple인 산화과정은 $E_{pa}$ = -0.70~-0.76V에서 준가역적으로 일어남을 알았다.

• 대한약리학회지
• /
• 제31권2호
• /
• pp.153-164
• /
• 1995

Sympathomimetic amines, especially ephedrine, are a major ingredient in proprietary medications for symptomatic treatment of upper respiratory infections. Their frequent uses can lead to occasional instances of abuse and habituation. The clinical symptoms of ephedrine abuse are similar to that of amphetamine psychosis and resemble closely that of schizophrenia. Because both amphetamine psychosis and schizophrenia are thought to be mediated primarily through the action on catecholamines, ephedrine-induced changes of the biogenic amines can be suspected. However, there were few studies about the central effects of ephedrine because of the milder central action than peripheral. Therefore, the present investigation was undertaken to elucidate the relations between the effects of single or repeated administration of ephedrine on the regional levels of biogenic amines in rat brain and ephedrine-induced CNS stimulation. The male Sprague-Dawley rats weighing $100{\sim}200\;g$ were used. After single or repeated administrations of ephedrine, blocks of tissue were obtained from frontal cortex, corpus striatum, hippocampus, thalamus, hypothalamus, substantia nigra and cerebellum. The concentration of biogenic amines(norepinephrine, epinephrine, dopamine, 5-hydroxytryptamine(5-HT)) and their metabolites (3,4-dihydroxyphenylacetic acid (DOPAC), homovanillic acid(HVA), 5-hydroxyindoleacetic acid(5-HIAA)) were measured by means of high performance liquid chromatography-electrochemical detector(HPLC-ECD). The results obtained were as follows: 1) In the normal rat, the concentration of norepinephrine was the highest in hypothalamus. Dopamine, DOPAC and HVA were highest in corpus striatum, and 5-HT and 5-HIAA were highest in substantia nigra. Epinephrine was not detectable in any part of the brain tissue. 2) In a single administration of ephedrine, the concentration of DOPAC was decreased in corpus striatum. However, the other biogenic amines and their metabolites were not changed. 3) In repeated administration of ephedrine, the concentration of norepinephrine was decreased in all brain region checked. Dopamine was decreased in corpus striatum and substantia nigra and, increased in hypothalamus, and HVA was decreased in corpus striatum. 5-HT was decreased in all brain region except cerebellum and, 5-HIAA was decreased only in frontal cortex. The ratio of 5-HIAA/5-HT was increased in corpus striatum, thalamus, hypothalamus and substantia nigra. These data indicated that, although a single administration of ephedrine did not change the central neurotransmitters, repeated administration of ephedrine caused the decreases of norepinephrine and 5-HT in the most regions of brain, which may be responsible for the emergence of abnormal behavioral effect after ephedrine abuse.