• Journal of Electrical Engineering and Technology
• /
• 제4권2호
• /
• pp.255-265
• /
• 2009

This paper presents the acoustic noise and mechanical vibration reduction of a coreless brushless DC motor with an air dynamic bearing used in a digital lightening processor. The coreless brushless DC motor does not have a stator yoke or stator slot to remove the unbalanced force caused by the interaction between the stator yoke and the rotor magnet. An unbalanced force makes slotless brushless DC motors vibrate and mechanically noisy, and the attractive force between the magnet and the stator yoke increases power consumption. Also, when a coreless brushless DC motor is driven by a $120^{\circ}$ conduction type inverter, high frequency acoustic noise occurs because of the peak components of the phase currents caused by small phase inductance and large phase resistance. In this paper, a core-less brushless DC motor with an air dynamic bearing to remove mechanical vibration and to reduce power consumption is applied to a digital lightening processor. A $180^{\circ}$ conduction type inverter drives it to reduce high frequency acoustic noise. The applied methods are simulated and tested using a manufactured prototype motor with an air dynamic bearing. The experimental results show that a coreless brushless DC motor has characteristics of low power consumption, low mechanical vibration, and low high frequency acoustic noise.

• 한국전기전자재료학회논문지
• /
• 제19권9호
• /
• pp.878-882
• /
• 2006

We have fabricated single organic layer devices of the organolanthanide complex, terbium tris-(1-phenyl-3-methyl-4-(tertiarybutyry)pyrazol-5-one)triphenylphosphine oxide [$(tb-PMP)_{3}Tb-(Ph_{3}PO)$] for the investigation of its light emission and electrical conduction properties. The thickness of ($(tb-PMP)_{3}Tb-(Ph_{3}PO)$) layer was varied to 60, 75, 95 nm. Mg and Ca layers were used for the cathode contact. The electrical conduction in the $(tb-PMP)_{3}Tb-(Ph_{3}PO)$ single layer devices was dominated by the injection of electrons into the organic layer from the cathode. A higher current density at much lower voltages can be attained with Ca cathode because of the enhanced electron injection. The device shows very sharp emission at 548 nm. The FWHM of the strongest emission peak was 12 nm.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.144-145
• /
• 2006

ZnO is a promising material to make high efficiency violet or blue light emitting diodes (LEDs) for its large binding energy (60meV) and big bandgap. But the high quality p-type conduction of ZnO is a dilemma to achieve LEDs with it. In present study, we presented a reliable method to prepare ZnO thin films on (100)silicon substrates by RF magnetron sputtering in the mixture ambient of $N_2$ and $O_2$, accompanying with low pressure annealing in the sputtering chamber in $O_2$ at $600^{\circ}C$ and $800^{\circ}C$ respectively. X-ray diffraction and Hail effect with Van der Paul method were performed to test ZnO films. Seeback effect was also carried out to identify carrier types in ZnO films and showed the N-doped ZnO film annealed at $800^{\circ}C$ had achieved p-type conduction.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 C
• /
• pp.1336-1338
• /
• 1997

Relations between the composites of SiC-$ZrB_2$ electro-conductive ceramic composites and their electrical resistivity, as well as their temperature, were investigated. The electrical resistivity of hot-pressed composites was measured by the Pauw method in the temperature of RT to $100^{\circ}C$. The electrical resistivity of the composites follow the electrical conduction model for a homogenous mixture of two kinds of particles with different conductivity. Also the electrical resistivity versus temperature curves indicate the formation of local chains of $ZrB_2$ particles. In the case of SiC-$ZrB_2$ composites containing above 30Vol.% $ZrB_2$ showed PTCR, whereas the electrical resistivity of SiC-15Vol.% $ZrB_2$ showed NTCR.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 C
• /
• pp.1525-1527
• /
• 1997

We deposited maleate copolymer films by using Langmuir-Blodgrtt(LB) method. The deposition status of LB films were verified by the measurement of capacitance which was increased with the number of layers. And, we have investigated anisotropy electrical conduction characteristics of maleate copolymer LB films by I-V measurement for perpendicular direction and horizontal direction.

• Tribology and Lubricants
• /
• 제17권2호
• /
• pp.124-129
• /
• 2001

The electrical and rheological behaviors of the cellulose phosphate ester suspension in the silicone oil were investigated. Cellulose phosphate ester suspension showed a typical ER response (Bingham flow behavior) upon application of an electric field. The shear stress for the cellulose phosphate ester suspension exhibited a linear dependence on the volume fraction of particles and a square power of the electric field. On the basis of the experimental results, cellulose phosphate ester suspension correlated with the conduction model of Tang et al, and found to be an ER fluid.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.129-133
• /
• 2005

This paper discusses DC/DC converter modeling using average model of switch and critical characterist. Average model of switch approach is expended to the modeling of boundary conduction mode DC/DC converters that operate at the boundary between Continuous Conduction Mode(CCM) and Discontinuous Conduction Mode(DCM). Frequency responses predicted by the average model of switch are verified by simulation and experiment.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제1권2호
• /
• pp.105-110
• /
• 2012

This paper designs the high-efficiency and the low-cost drive system of the smallsize electric vehicles (EVs). The power circuit for driving the dc motor is designed by considering both the cost and efficiency. In order to reduce the conduction loss of MOTFET and diode for controlling an armature voltage, some MOSFETs and diodes at the armature are in parallel connection. An operating sequence for both the field current and the armature voltage according to the accelerator pedal angle is suggested for changing smoothly the rotating direction of dc motor. Through the simulation studies, the performances of the proposed methods are verified.

• Current Applied Physics
• /
• 제18권12호
• /
• pp.1492-1495
• /
• 2018

This paper studies the influence of temperature on electrical resistivity in ${\alpha}-InAs$ thin films between 30 K-2K based on the analysis of Mott VRH model and ES VRH model. The effect of the interactions between electrons at lower temperature must be considered, therefore, ES VRH conduction will dominate mechanism, and the crossover from Mott to ES VRH conduction is observed about 7 K. Based on available experiment data and VRH conduction model, the parameters of VRH conduction are determined. And the calculated values of $T_C$ are consistent with the experimental results. In addition, $R_M/{\xi}$, ${\Delta}_M/kT$, $R_{ES}/{\xi}$ and ${\Delta}_{ES}/kT$ are satisfied with the validity of Mott and ES models. Furthermore, the temperature dependence of resistivity at low temperature obeys a universal scaling law, which well describes the overall temperature range of VRH conduction. However, the values of $T^{\prime}_M$ from the universal function are two order of magnitudes lower than $T_M$ deduced from fitting experiment.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 1999년도 학술대회논문집-국제 전기방전 및 플라즈마 심포지엄 Proceedings of 1999 KIIEE Annual Conference-International Symposium of Electrical Discharge and Plasma
• /
• pp.157-161
• /
• 1999

This paper presents a Single-phase Semi-Bridge PWM Converter, which features Continuos Conduction Mode and Phase-adjusted Unipolar PWM Method. The reduced conduction losses are achieved by the employment of a single converter, instead of the typical configuration composed of a front end rectifier followed by a boost converter. Theoretical principle of operation, a design example and Simulation results of a 3kW Semi-Bridge PWM converter with 220 Vrms input voltage and 400 Vdc output voltage are presented.