• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.60-60
• /
• 2008

We manufactured Liquid Crystal Polymer (LCP) and (1-x)$BaTiO_3-xSrTiO_3$(BST) ceramic composites and investigated dielectric properties to use as embedded capacitor in printed circuit boards and replace LTCC substrates. The dielectric properties of these composites are varied with volume fraction of BST and ratios of BT/ST. Dielectric constants are in the range of 3~28. In addition, we could get low TCC and High Q value that could not achieve in other ceramic-polymer composites. Especially, in composite with x=0.4 and 50vol% BST, the dieletric constant and Q-value are 27 and 300, respectively. And more TCC is -116~145ppm/$^{\circ}C$ in the temperature range of -55~$125^{\circ}C$. We think that this composites can be used high-Q substrate material like LTCC and embedded temperature compensation capacitor in printed circuit boards.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.232-233
• /
• 2007

We manufactured Liquid Crystal Polymer (LCP) and (1-x)CaTiO3-xLaAlO3 (CT-LA) ceramic composites and investigated dielectric properties to use as embedded capacitor in printed circuit boards and replace LTCC substrate. The dielectric properties of these composites are varied with volume fraction of CT-LA and ratios of CT/LA. Dielectric constants are in the range of 3~15. In addition, we could get low TCC and High Q value that could not achieve in other ceramic-polymer composites. Especially, in composite with x=0.01 and 30 vol% CT-LA, the dieletric constant and Q-value are 10 and 200, respectively. And more TCC is $-28{\sim}300ppm/^{\circ}C$ in the temperature range of $-55{\sim}125^{\circ}C$. We think that this composites can be used high-Q substrate material like LTCC and embedded temperature compensation capacitor in printed circuit boards.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.46-50
• /
• 2003

Crystal structure and microwave dielectric properties of $Ba(Mg_{1/3-x}Nb_{2/3})O_3$ (BMN) ceramics were investigated. $Ba(Mg_{1/3}Nb_{2/3})O_3$ has the 1:2 ordered hexagonal structure. The 1:2 ordering and relative density of specimens increased with small Mg deficiency(x). The variation of Q-value with Mg deficiency is very similar to that of 1:2 ordering and relative density. The highest $Q{\times}f_0$ achieved in this investigation is about 96,000 for $Ba(Mg_{1/3-0.02}Nb_{2/3})O_3$. The improvement of Q-value with Mg-deficiency is related to the increase of degree of ordering and relative density of the specimen.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.9
• /
• pp.720-725
• /
• 2001

In this study, Pb(La,Ce)Ti $O_3$ ceramics were manufactured for 20 MHz resonator application. Electromechanical coupling factor( $k_{t}$, $k_{t3}$, mechanical quality factor( $Q_{mt}$ , $Q_{mt3}$ and dydnamic range (D.R) of thickness vibration mode were measured as the variations of $\ell$/t(length/thickness) ratio of ceramic substrates. Mechanical quality factor( $Q_{mt3}$) and dynamic range of third overtone thickness vibration mode showed the highest value of 2,773 and 52.22dB at specimen S4($\ell$/t=12), respectively. The excellent temperature stability of resonant frequency suitable for resonator application was shown, regardless of thermal shock.k.ock.k.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.203-204
• /
• 2007

This paper investigated the influence on partial discharge distribution of various defects at the model power cable joints interface using K-means clustering. As the result of analyzing discharge number distribution of ${\Phi}-n$ cluster, clusters shifted to $0^{\circ}\;and\;180^{\circ}$ with increasing applying voltage. It was confirmed that discharge quantity and euclidean distance between centroids were increased with applying voltage from the analyzing centroid distribution of ${\Phi}-q$ cluster. The degree of dispersion was increased with calculating standard deviation of ${\Phi}-q$ cluster centroid. The tendency both number of discharge and mean value of ${\Phi}-q$ cluster centroid were some different with defect types.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.3-8
• /
• 1995

Since Interior Permanent Magnet syncronous Motor has a structure whose magnet is inserted in the rotor, d, q inductance is differ and the motor products hybrid torque combined allignment term and reluctance term. Air gap flux density and d, q axis inductances of the Interior Permanent Magnet Synchronous Motor obtained by analytical method are compensated using Finite Element Method. For optimal design, the efficiency of the motor is taken as the objective function, and Genetic Algorithm finds the value of design parameters which maximize the objective function.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.2
• /
• pp.504-510
• /
• 2015

Because wind generators (WGs) in a wind power plant (WPP) produce different active powers due to wake effects, the reactive power capability of each WG is different. This paper proposes a hierarchical voltage control scheme for a WPP that uses a WPP controller and WG controller. In the proposed scheme, the WPP controller determines a voltage error signal by using a PI controller and sends it to a doubly-fed induction generator (DFIG). Based on the reactive current-voltage ($I_Q-V$) characteristic of a DFIG, the DFIG injects an appropriate reactive power corresponding to the voltage error signal. To enhance the voltage recovery capability, the gains of the $I_Q-V$ characteristic of a DFIG are modified depending on its reactive current capability so that a DFIG with greater reactive current capability may inject more reactive power. The proposed scheme enables the WPP to recover the voltage at the point of common coupling (PCC) to the nominal value within a short time after a disturbance by using the adaptive $I_Q-V$ characteristics of a DFIG. The performance of the proposed scheme was investigated for a 100 MW WPP consisting of 20 units of 5 MW DFIGs for small and larger disturbances. The results show the proposed scheme successfully recovers the PCC voltage within a short time after a disturbance.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.5
• /
• pp.492-496
• /
• 2004

In this study, (0.96 －x)(PSN-PZT)－xBF－0.04 PNW＋0.3wt%MnO$_2$＋0.6wt%CuO ceramics were fabricated with the variations of the amount of BiFeO$_3$substitution and sintering temperature for the development of modified ceramics which can be sintered in the low temperature($\leq$100$0^{\circ}C$ ), and their microstructural, dielectric and piezoelectric characteristics were investigated. As the amount of BiFeO$_3$ substitution was increased, the density, mechanical quality factor(Q$_{m}$) and electromechanical coupling factor(k$_{p}$) showed the maximum value at each of sintering temperature. At sintering temperature of 98$0^{\circ}C$ and BiFeO$_3$substitution of 2 mol%, the density, dielectric constant and electromechanical coupling factor(k$_{p}$) showed the maximum value of 7.84 g/㎤, 1415 and 0.49, respectively. And at sintering temperature of 95$0^{\circ}C$ and BiFeO$_3$substitution of 3mol%, mechanical quality factor showed the maximum value of 1062. 1062.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.294-296
• /
• 1999

Solid solution ceramics having various ratios between xPb( $Y_{1}$2/T $a_{1}$2/) $O_3$ and Pb(Z $r_{0.52}$ $Ti_{0.48}$) $O_3$were synthesized by a conventional solid state reaction for well sintered specimens, dielectric and piezoelectric prperties were studied as a function of composition. The dielectric constant of PYT-PZT ceramics of 4 mol% PYT was 1,424 at room temperature. The maximum value of electromechanical couping facotr $k_{p}$ of 51% $k_{t}$ of 30% were obtained at the composition of 4 mol% PYT, howerver mechanical quality factor( $Q_{m}$) had a minimum value of 69 at 4 mol% PYT. Also the maximum value of piezoelectric constant of $D_{33}$(310[pC/N]) and $d_{31}$(-131[pC/N]) were obtained at the composition of 4 mol% PYT content.ntent.t.t.t.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.4
• /
• pp.285-289
• /
• 2009

Small RFID tag antenna were fabricated on Si substrate and their physical and electrical properties were evaluated. With decreasing the size of tag antenna on Si substrate, small SMD-type RFID tags could be fabricated, which is very useful for various applications including PCB tracking. Firstly, electromagnetic properties on tag antenna pattern were simulated with HFSS. The setup frequency was 13.56 MHz of HF-band RFID. The line-width and line-gap were modeled in the range of $50{\sim}200{\mu}m$. S parameters, SRF, and Q value were calculated from the model. When the line-width and line-gap were 100 urn and the loop-turn was 10, the SRF was 80 MHz and the Q value was ca. 9. When the microstrip antenna pattern of aluminum was fabricated by using DC sputtering, Vpp of ca. 1.6 V was obtained when the reader-tag distance was 40 mm.