• Solar Energy
• /
• v.20 no.3
• /
• pp.75-84
• /
• 2000

The purpose of this research is to study on the heat transfer characteristics of separate type heat pipe with a rotor. The heat transfer characteristics of the rotor condenser are various on input heat of evaporator, rotational speeds of rotor, and working fluid amount. The results obtained from the study are as follows. 1. Magnetic fluid using seal of the rotor operated in stability by a variation of temperature and rotation speeds. The configuration of magnetic fluid seal assembly was adequate. 2. Steam ejector is effective in recovering working fluid condensate in the rotor. When steam ejector is operating, the heat flux of working fluid does not change, with the wall temperature in the rotor. 3. The optimum design conditions on working fluid amount and rotational speeds are effective in evaporator volume 50%, rotational speeds 200rpm, 300rpm, and operating temperature $80^{\circ}C$. With working fluid amount increasing, overall heat transfer coefficient decreases linearly.

• Environmental and Resource Economics Review
• /
• v.10 no.4
• /
• pp.495-513
• /
• 2001

We investigate a practical method of calculating the impact of multiple domestic energy price change on the final demand, production, the export and import change, the change in the balance of payment of Korean economy. By combining an existing computable general equilibrium (CGE) model with the traditional input-output analysis with two additional assumptions on the price behavior, we provide a cost-effective method of analyzing the impact of multiple energy price changes on the domestic economy. The energy price shock we used in this paper is 0.127% increase weighted by the sectoral productions. The total impacts on price level and GDP are 1.258% and -0.940%, respectively. The impact on the total output (GDP and intermediate goods) is about -1.580%.

• Solar Energy
• /
• v.19 no.4
• /
• pp.1-10
• /
• 1999

The phenomena of energy separation through the vortex tube was investigated experimentally, to see the effect of nozzle area ratio and partial admission rate on the energy separation and cooling capacity. The experiment was tarried out with various nozzle area ratios from 0.031 to 0.232 and partial admission rate from 0.176 to 0.956 by varying input pressure($0.2{\si\m}0.5$ MPa) and cold air mass fraction($y=0.1{\sim}1.0$). From the experimental result, we found the optimum nozzle area ratio and the effective partial admission rate for the available use and best cooling performance in given operation condition. While the maximum drop of cold air temperature was observed at around y=0.3 and $S_n=0.155$, the maximum cooling capacity was observed at around y=0.6 and $S_n=0.094$.

• Environmental and Resource Economics Review
• /
• v.20 no.2
• /
• pp.309-333
• /
• 2011

Korea is one of the countries that propel new renewable energy industrialization actively in the context of change in this industrial structure. The previous government declared this kind of industrialization as a national goal in 2004 and the current government also supports this strategy. However, it is necessary to check whether this strategy is proper and effective. The reason is because solar, wind and fuel cells that have attracted public attention as the new growth engines cannot replace main industries yet. This paper tries to analyze the economic effects of new renewable energy industrialization by dividing them into production effect and job creation effect. The result of this analysis shows that solar energy is not effective at all, while wind energy is very effective in both production and job creation. In conclusion, this paper suggests that the government has to propel new renewable energy industrialization after consideration of these kinds of economic effects.

• Journal of Radiation Protection and Research
• /
• v.47 no.2
• /
• pp.99-106
• /
• 2022

Background: The radionuclide inventory calculation codes such as ORIGEN and FISPACT collapse neutron reaction libraries with energy spectra and generate an effective one-group cross-section. Since the nuclear cross-section data, energy group (g) structure, and other input details used by the two codes are different, there may be differences in each code's activation inventory calculation results. In this study, the calculation results of neutron-induced activation inventory using ORIGEN and FISPACT were compared and analyzed regarding radioactive waste classification and worker exposure during nuclear decommissioning. Materials and Methods: Two neutron spectra were used to obtain the comparison results: Watt fission spectrum and thermalized energy spectrum. The effective one-group cross-sections were generated for each type of energy group structure provided in ORIGEN and FISPACT. Then, the effective one-group cross-sections were analyzed by focusing on ⁵⁹Ni, ⁶³Ni, ⁹⁴Nb, ⁶⁰Co, ¹⁵²Eu, and ¹⁵⁴Eu, which are the main radionuclides of stainless steel, carbon steel, zircalloy, and concrete for decommissioning nuclear power plant (NPP). Results and Discussion: As a result of the analysis, ¹⁵⁴Eu and ⁵⁹Ni may be overestimated or underestimated depending on the code selection by up to 30%, because the cross-section library used for each code is different. When ORIGEN-44g, -49g, and -238g structures are selected, the differences of the calculation results of effective one-group cross-section according to group structure selection were less than 1% for the six nuclides applied in this study, and when FISPACT-69g, -172g, and -315g were applied, the difference was less than 1%, too. Conclusion: ORIGEN and FISPACT codes can be applied to activation calculations with their own built-in energy group structures for decommissioning NPP. Since the differences in calculation results may occur depending on the selection of codes and energy group structures, it is appropriate to properly select the energy group structure according to the accuracy required in the calculation and the characteristics of the problem.

• Journal of Energy Engineering
• /
• v.19 no.3
• /
• pp.143-150
• /
• 2010

Line source method of borehole system assumes the entire surrounding medium is uniform. However, thermal properties of grouting region are considerably different from those of surrounding soil. In this study we investigate the effect of grouting materials on the solution of line source method with the aid of numerical analysis. This numerical model generates the temperature of borehole fluid with which line source solution can be obtained. Then this solution can be compared with input condition of numerical model. The results of this comparison show that thermal conductivity and borehole thermal resistance of line source solution are approximately 86% and 91% of the input condition of numerical model. Chart method is developed in this study to find the numerical input conditions (thermal conductivity and borehole thermal resistance) from the line source solution. Thermal response test of test borehole is conducted, the results of which are approximately consistent with the Chart method. Thermal property changes of grouting materials on the line source solution are also examined.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.41 no.1
• /
• pp.115-122
• /
• 1996

One of the most laborious work in rice farming is transplanting of rice seedling which has been required preparation of nursery bed and care of seedling during one month period. In this research, direct seeding in dry paddy(DS) and direct seeding in wet paddy(WS) were practiced to compare with traditional transplanting(TP) in Suwon. Growth stages in direct seeding were delayed as its planting time was about 21 days later than those of TP. Heading stage of direct seeding at Suwon was delayed about 9 days as compared to transplanting culture. Rice yield was not different between the seeding practises. Working-hour saving was about 17％(DS) and 28％(WS). Production cost of direct seeding was decreased 20％(DS) and 32％(WS), respectively. Amount of rice production per a unit working-hour in direct seeding could increase 14％(DS) and 39％(WS) compared to that of TP, respectively. Therefore, direct seeding could save significantly working hour and production cost without reducing rice yield. WS was more effective than DS in saving labor and production cost. Direct seeding was not efficient method in input of farming energy and agricultural chemicals.

• Transactions of the Korean hydrogen and new energy society
• /
• v.25 no.3
• /
• pp.297-304
• /
• 2014

The purpose of this study is to evaluate the experimental performance characteristics of a water-to-water geothermal heat pump featuring a vapor refrigerant injection for the production of hot water. The performance of geothermal heat pump with a vapor injection was evaluated by comparing with that of a conventional geothermal heat pump without a vapor injection. For heating operation, the geothermal heat pump with a vapor injection is superior in COP and heating capacity. The vapor injection was more effective for supplying hot water while overloading. The vapor injection was effective for the improvement of the cooling capacity. However, the vapor injection was not effective for the increasing of COP according to the increased input of a compressor. The advantage of vapor injection in water-to-water geothermal heat pump become disappeared while cooling operation with lower part loading.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.25 no.6
• /
• pp.310-316
• /
• 2013

This study was designed to investigate a method for short-term, real-time energy demand prediction, to cope with changing loads for the effective operation and management of buildings. Through a case study, a novel methodology for real-time energy demand prediction with the use of weather forecasting data was suggested. To perform the input and output operations of weather data, and to calculate solar radiation and EnergyPlus, the BCVTB (Building Control Virtual Test Bed) was designed. Through the BCVTB, energy demand prediction for the next 24 hours was carried out, based on 4 real-time weather data and 2 solar radiation calculations. The weather parameters used in a model equation to calculate solar radiation were sourced from the weather data of the KMA (Korea Meteorological Administration). Depending on the local weather forecast data, the results showed their corresponding predicted values. Thus, this methodology was successfully applicable to anywhere that local weather forecast data is available.

• Structural Engineering and Mechanics
• /
• v.18 no.3
• /
• pp.287-301
• /
• 2004

Structural acceleration regulation is a means of managing structural response energy and enhancing the performance of civil structures undergoing large seismic events. A quadratic output regulator that minimizes a measure including the total structural acceleration energy is developed and tested on a realistic non-linear, semi-active structural control case study. Suites of large scaled earthquakes are used to statistically quantify the impact of this type of control in terms of changes in the statistical distribution of controlled structural response. This approach includes the impulses due to control inputs and is shown to be more effective than a typical displacement focused control approach, by providing equivalent or better performance in terms of displacement and hysteretic energy reductions, while also significantly reducing peak story accelerations and the associated damage and occupant injury. For earthquake engineers faced with the dilemma of balancing displacement and acceleration demands this control approach can significantly reduce that concern, reducing structural damage and improving occupant safety.