• 한국해양공학회지
• /
• 제23권1호
• /
• pp.74-80
• /
• 2009

In this study, the static and modal analyses to find the characteristic of eigenvalues for a towed cable were with a free boundary condition at the bottom end carried out with numerical study. The resulting numerical code with finite element method was used to study sample problems for a cable with towing speeds. After tracing the equilibrium state with a towing speed through the static analysis, modal analysis on the basis of static results was performed. The static top tension for a critical towing speed is nearly 50 percent of what it was for a free hanging pipe. From static analyses, it is found that towing speed has a noticeable effect on top tension of a towed pipe. At a high towing speed, differences between the first and second periods become larger. Compared to the fundamental period for a free hanging pipe, that for a towed pipe with a critical towing speed is approximately 1.4 times larger. This result is very important point in that the lock in condition and tension of the towed cable system with top excitation can be predicted. The corrected close form solution to solve natural periods for a towed cable was presented in this study. The code is validated by comparison of the results of theoretical and numerical studies. Two results were in very good agreement. This study can contribute to predicting the lock-in condition and tension for a towed cable or pipe with top excitation.

• 한국강구조학회 논문집
• /
• 제23권2호
• /
• pp.199-210
• /
• 2011

사장교의 케이블은 타 부재에 비해 단면적이 매우 작고 고응력 상태이므로 진동에 매우 민감한 부재이다. 따라서 사장교 케이블의 충격계수는 실제 차량의 주행으로 발생하는 동적 효과를 반영하여 평가하는 것이 합리적이다. 이에 본 연구에서는 차량 중량, 케이블 모델, 노면조도, 차량속도 및 차량간격의 설계변수를 고려하여 중앙경간 230m 및 540m의 강합성 사장교를 대상으로 차량 이동하중 해석을 수행하여 케이블의 충격계수를 평가하고, 현재 실무에서 사용되고 있는 영향선을 이용한 방법과 비교하였다. 본 연구에 사용된 노면조도는 ISO 8608 규정에 근거하여 랜덤 생성하였으며, 생성 회수에 따른 케이블 충격계수의 수렴 추이를 분석함으로써 결과의 신뢰도를 확보하였다. 또한, 차량모델은 9-자유도를 갖는 트랙터-트레일러 형식의 트럭 모델을 적용하였으며 차량의 운동방정식은 Lagrange운동방정식으로부터 유도하였다. 해석 대상 교량은 3차원 유한요소모델로 구축하였으며 보강형과 주탑은 보요소, 케이블은 등가탄성계수를 갖는 트러스요소를 사용하였다. 이동하중으로 인한 교량-차량 상호작용 해석에는 직접적분법을 사용하였으며, 교량의 변위 오차율이 허용 범위 내에 수렴될 때까지 반복 해석을 수행하였다. 그 결과, 실제 차량의 주행으로 발생하는 동적 효과를 고려하지 못하는 영향선 기법은 차량 이동하중 해석에 비해 측경간 단부 케이블의 충격계수를 과소평가할 수 있는 것으로 나타났다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제18권6호
• /
• pp.147-154
• /
• 2014

사장교 케이블의 손상은 사장교 전체의 안전에 가장 큰 영향을 주는 요인이 되므로 케이블의 손상에 대한 유지관리를 필수적으로 해야한다. 이러한 유지관리의 대표적인 방법으로 케이블의 고유진동수변화을 추적하는 방법이 있다. 지금까지 케이블의 고유진동수는 진동법에 의해 횡방향 진동으로 추정하여 왔으며 시스템인식기법은 반복법에 의한 민감도방정식으로 축방향강성을 추정하나 새그의 영향으로 종방향운동에 대한 고유진동수의 분포에 대한 연구가 필요하다. 이 연구에서는 종방향운동에 의한 고유진동수를 이용하여 손상을 추정함으로써, 종방향운동의 신뢰성을 향상시키는 새로운 방법을 제안하였다. 이 방법의 적용결과를 근사해인 유한요소해석결과와 비교하여 유사한 결과를 얻음으로써 제안된 방법의 신뢰성을 검증하였다. 따라서, 케이블손상과 고유진동수와의 관계를 분석한 결과는 손상률이 증가할수록 고유진동수는 낮게 나타났다. 따라서 케이블의 실측 고유진동수를 알 때 케이블손상과 고유진동수와의 관계식을 통해 케이블의 손상정도를 추정할 수 있으므로 케이블의 효율적인 유지관리가 가능하게 된다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 추계 학술논문 발표대회
• /
• pp.181-184
• /
• 2012

The Tuned Pendulum Slab Damper(TPSD)system is mainly composed of suspended pendulum slab which was hanging with cable wire from the top floor of building without any extra loads structurally, and can be helpful to reduce vibration with effect of tuned mass damper function by the principle of pendulum movement. The experiment was performed with miniatures of the 30stories of steel structure building by the forced vibration test using shaking table, and the result was reduced about 42% of vibration. The purpose of this study was to make analysis of application of the TPSD system to new building and exist building against strong wind or seismic wave. The result of this study was that the TPSD system shall be satisfactory in field of execution, process control, safety and economical efficiency with saving up to 70% of construction cost.

• Smart Structures and Systems
• /
• 제3권3호
• /
• pp.341-356
• /
• 2007

A good understanding of normal modal variability of civil structures due to varying environmental conditions such as temperature and wind is important for reliable performance of vibration-based damage detection methods. This paper addresses the quantification of wind-induced modal variability of a cable-stayed bridge making use of one-year monitoring data. In order to discriminate the wind-induced modal variability from the temperature-induced modal variability, the one-year monitoring data are divided into two sets: the first set includes the data obtained under weak wind conditions (hourly-average wind speed less than 2 m/s) during all four seasons, and the second set includes the data obtained under both weak and strong (typhoon) wind conditions during the summer only. The measured modal frequencies and temperatures of the bridge obtained from the first set of data are used to formulate temperature-frequency correlation models by means of artificial neural network technique. Before the second set of data is utilized to quantify the wind-induced modal variability, the effect of temperature on the measured modal frequencies is first eliminated by normalizing these modal frequencies to a reference temperature with the use of the temperature-frequency correlation models. Then the wind-induced modal variability is quantitatively evaluated by correlating the normalized modal frequencies for each mode with the wind speed measurement data. It is revealed that in contrast to the dependence of modal frequencies on temperature, there is no explicit correlation between the modal frequencies and wind intensity. For most of the measured modes, the modal frequencies exhibit a slightly increasing trend with the increase of wind speed in statistical sense. The relative variation of the modal frequencies arising from wind effect (with the maximum hourly-average wind speed up to 17.6 m/s) is estimated to range from 1.61% to 7.87% for the measured 8 modes of the bridge, being notably less than the modal variability caused by temperature effect.

• Wind and Structures
• /
• 제18권5호
• /
• pp.511-528
• /
• 2014

The characteristics of wake galloping phenomenon for two parallel/unparallel circular cylinders were investigated via wind tunnel tests. The two cylinders were initially deployed in parallel and wake galloping phenomena were observed by varying the center-to-center distance. The effect of an unparallel arrangement of two cylinders was next investigated by fixing the spacing ratio of one side of the cylinders at 5.0D and the other side at 3.0D, in which D represents the diameter of the cylinder. For the unparallel disposition, the 5.0D side showed a small, limited vibration while the 3.0D side produced much larger amplitude of vibration, resulting in a rolling motion. However, the overall amplitude appeared to decrease in unparallel disposition when compared with the amplitude of the 3.0D - 3.0D parallel case. This represents the mitigation effect of wake galloping due to the unparallel disposition between two cylinders. Flow visualization tests with particle image velocimetry were conducted to identify flow fields between two cylinders. The test results demonstrate the existence of a complex interaction of the downstream cylinder with the shear layer generated by the upstream cylinder. When the spacing ratio was large enough, the shear layer was not observed and the downstream cylinder showed only limited random vibration.

• 화약ㆍ발파
• /
• 제16권3호
• /
• pp.25-34
• /
• 1998

This area is covered in Andesite of high compression strength and located in PUSAN SEO-KU. There are many old houses around shaft site. So, we must have a cautious blasting operation. A total of 40 blasts were test at DAE-SHIN Shaft site to study the magnitude and frequency characterization of blast-induced vibration. The effect of viblating frequency on structual damage and site-specific scaling to define th empirical equations were also discussed. The result can be summarized as follows: 1. Some empirical equations were obtained. $V=K\{{\frac{D}{W}}1/3\}^{-n}$ where the values for n and K are estimated to be -1.407 to -2.202 and 643.3489 to 7283.2104 respectively. 2. Dominant frequencies at short distance are in the range of about 75.0 to 91.8 Hz, with some exceptions of about 50Hz, Frequencies observed at long distance are in the range of 10 to 2Hz. It is apparent the shift of dominant frequency down to lower levels at long distance.

• 한국터널지하공간학회 논문집
• /
• 제16권2호
• /
• pp.213-224
• /
• 2014

최근, tunnel boring machine (TBM)을 이용한 도심지 지중 전력구 터널 건설이 증가하고 있다. 쉴드 TBM을 이용한 기계화 터널 굴착 공법은 재래식 공법에 비해 지반침하를 최소화 하고 발파에 의한 진동을 줄일 수 있는 장점이 있다. 국내에서는 earth pressure balance(EPB) 쉴드 TBM이 주로 사용되고 있다. 그러나 전력구 터널 굴착을 위한 쉴드 TBM 공법이 증가함에도 불구하고, 전력구 쉴드 TBM 터널의 거동 분석에 관한 연구는 미비한 실정이다. 본 연구에서는 후방주입 거리에 따른 전력구 쉴드 TBM 터널의 거동 특성을 분석하고, 굴착면 지반 손실과 후방주입 거리와의 상관관계를 도출하고자 한다. 쉴드 TBM을 이용한 터널 굴착은 3D FEM을 이용하여 시뮬레이션 하였다. 뒷채움 그라우트가 설치되는 거리의 변화에 따른 축력, 전단력, 휨 모멘트와 같은 단면력을 검토하고 지표면에서의 연직 변위를 분석하였다. 또한, 유한요소해석으로 얻어진 결과와 안정성 분석에 기초하여, 지반과 터널 구조물의 안정성을 확보할 수 있는 뒷채움재 주입시기를 결정할 수 있다.

• Smart Structures and Systems
• /
• 제17권3호
• /
• pp.363-389
• /
• 2016

Deficient modes that cannot be always identified from different sets of measurement data may exist in the application of operational modal analysis such as the stochastic subspace identification techniques in large-scale civil structures. Based on a recent work using the long-term ambient vibration measurements from an instrumented cable-stayed bridge under different wind excitation conditions, a benchmark problem is launched by taking the same bridge as a test bed to further intensify the exploration of mode identifiability. For systematically assessing this benchmark problem, a recently developed SSI algorithm based on an alternative stabilization diagram and a hierarchical sifting process is extended and applied in this research to investigate several sets of known and blind monitoring data. The evaluation of delicately selected cases clearly distinguishes the effect of traffic excitation on the identifiability of the targeted deficient mode from the effect of wind excitation. An additional upper limit for the vertical acceleration amplitude at deck, mainly induced by the passing traffic, is subsequently suggested to supplement the previously determined lower limit for the wind speed. Careful inspection on the shape vector of the deficient mode under different excitation conditions leads to the postulation that this mode is actually induced by the motion of the central tower. The analysis incorporating the tower measurements solidly verifies this postulation by yielding the prevailing components at the tower locations in the extended mode shape vector. Moreover, it is also confirmed that this mode can be stably identified under all the circumstances with the addition of tower measurements. An important lesson learned from this discovery is that the problem of mode identifiability usually comes from the lack of proper measurements at the right locations.

• 대한토목학회논문집
• /
• 제14권6호
• /
• pp.1299-1308
• /
• 1994

본 연구는 사장교의 차량하중에 의한 동적거동을 파악하고자 수치해석상 비교적 간단한 일본의 풍리(豊里)(Toyosato)대교(大橋)의 자료를 근거로하여 수치해석 대상모델을 구조형식별로, 여러가지 설계변수-즉, (1) 경간비, (2) 중앙경간장과 주탑높이와의 비, (3) 거어더의 강성, (4) 주탑의 강성, (5) 케이블의 강성-을 변화시켜 수치해석을 수행하여 동적거동을 파악하고, 그 결과를 가지고 설계변수의 영향 및 충격계수의 변화에 대하여 비교 분석하였다. 이때 변위 및 단면력의 영향선을 구하기 위한 해석은 전달행렬법을 이용하였으며, 동적해석에 있어서는 평면구조계의 집중질량계로 모델을 가정하여 차량과 교량의 운동방정식을 유도한 후 모드중첩법을 사용하여 각 질점에 대한 변위 및 단면력의 동적시간이력을 구하였다.