• Journal of Electrical Engineering and Technology
• /
• v.13 no.6
• /
• pp.2292-2300
• /
• 2018

A field-circuit coupling model of a typical faulty generator is established to correct through-bolt end-region overheating and breakdown failure in a tubular hydro-generator. Using the model, eddy current loss and electromagnetic forces on through bolts under normal and failure conditions are analyzed and compared and the natural frequency of a through bolt is determined. Based on the analysis results, the causative mechanism of failure is revealed and targeted improvement design measures are proposed. The numerical results are found to be consistent with the actual fault characteristics, validating the design measure improvements. The results are useful in improving the design and manufacturing standards and enhancing the operational reliability of large tubular hydro-generators.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.22 no.5
• /
• pp.333-343
• /
• 2010

In Mokpo coastal zone, the characteristics showing ebb-dominant tidal flow was confirmed by analysis of observed tide and tidal currents, Physical factors occurring ebb-dominant flow were reviewed. Influence of critical depth for drying, bottom shear stress, coastal reclamation, tidal amplitude, nonlinear tide, and eddy viscosity on the change of ebb-dominant flow was investigated by applying a two-dimensional circulation model. The simulation results for a variety of conditions showed that eddy viscosity and critical depth for drying does little or no impact on the generation of asymmetric flow. Strong bottom friction stress makes ebb-dominant flow clearly. Change of tidal flat into land swells ebb- dominant flow, and change of tidal flat into sea disappears ebb-dominant flow. Nonlinear tides play a decisive role in the generation of asymmetrical tidal flow. Non-linear tides should be included in the open boundary conditions of hydrodynamic modeling in the Mokpo coastal zone.

• Journal of the korean society of oceanography
• /
• v.37 no.3
• /
• pp.169-177
• /
• 2002

An eddy-resolving free-surface primitive-equation model with nonlinear terrain-following coordinates is established to study the exchange of water masses among the Asian marginal seas and their adjacent waters. A curvilinear coordinate system is used to generate the horizontal grid with a variable resolution for the regional oceans from $5^{\circ}$S to $45^{\circ}$N and $100^{\circ}$E to $155^{\circ}$E. The higher resolution region has about a 10 km by 10 km grid covering the complex geometry of the coastal marginal seas, while the lower resolution region has about a 30 km by 30 km grid covering the eastern Pacific. The model is initialized by the Levitus annual climitology and forced by the monthly mean air-sea fluxes of momentum, heat, and freshwater derived from the Comprehensive Ocean-Atmosphere Data Set. High-resolution and low-viscosity are identified as the key factors for a better representation of the exchange of waters through narrow straits and passages between the marginal seas and their adjacent waters. The dynamics of the loop currents and eddies in the South China Sea and Celebes Sea are examined in detail. It has found that the anticyclonic loop and detached eddies from the Kuroshio through the Luzon Strait play an important role in transporting warm and salty water into the South China Sea, while the cyclonic circulation of the Mindanao Current in the Celebes Sea plays a role in contributing cold water to the Indonesian throughflow. The deep undercurrent of the western Pacific is shown to provide fresher water to the South China Sea and Celebes Sea. These modeling results suggest that the exchange processes via the narrow straits and passages are of fundamental importance to the maintenance of water masses for the marginal sea region.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.24 no.3
• /
• pp.429-435
• /
• 2019

The drifters of the Global Drifter Program were deployed in the northern East Sea for two years from March 2015 to compare and validate currents estimated from sea-level measurements with the SARAL/AltiKa altimetry satellite mission, specially designed to accurately measure sea level in the near-coastal area. The collocated (less than 20 km apart) directly measured current from GPS locations every 30 minutes and the currents normal to the satellite tracks show a similar correlation in the area shallower than 200 m depth as the open ocean and it makes it possible to investigate the time variations of the current along the coast in the northern East sea, where direct observations of current are scarce. The Liman Current along the Siberian coast is found to be southward all year round, but the North Korean Cold Current flows southward only in the summer. The North Korean Cold Current south of the Musudan cape mostly flows to the south, but the current direction depends on the presence of an eddy around the coast of Musudan cape.

• Fire Science and Engineering
• /
• v.16 no.2
• /
• pp.8-13
• /
• 2002

Induction heating is widely used in today's industry, in operations such as metal hardening, pre-heating for forging operations, melting or cooking. In this paper, the magneto-thermal analysis of an induction heating jar(IH-JAR) was presented as an efficient design. The magnetic field intensity inside the axisymmetric shaped cooker was analyzed using three-dimensional axisymmetric finite element method(FLUX2D) and the effectual heat source was obtained by ohmic losses from eddy currents induced in the jar. The heat was calculated using the heat source and heating equation. Also, it was presented the temperature characteristics of the IH-JAR according to time and relative permeability in stainless parts and in aluminum parts.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.5B no.1
• /
• pp.34-38
• /
• 2005

The finite element method is very flexible for new shapes and provides flux distribution, magnetomotive force, eddy currents, and torques. However, it requires lengthy computational time in order to achieve desired accuracy. The magnetic equivalent circuit method takes less computation time than the finite element method. Therefore, the finite element method is mainly used to confirm the completed design. The magnetic equivalent circuit method is convenient for complicated analysis of the transient state of the induction motor. The magnetic equivalent circuit method is restricted to only one direction of magnetic flux. In this paper, the construction elements (that is, stator iron, rotor iron, yoke, air gap, etc.) of the squirrel cage induction motor were represented by a flux tube and the air gap magnetomotive force was calculated by the magnetic equivalent circuit method. Starting transient torque and phase current of the squirrel cage induction motor were verified by the theoretical calculation and the experiment.

• Progress in Superconductivity and Cryogenics
• /
• v.4 no.1
• /
• pp.78-83
• /
• 2002

Since the KSTAR superconducting magnet structure should be maintained at a cryogenic temperature of about 4 K, even a small amount of heat might be a major cause of the temperature rise of the structure. The Joule heating by eddy currents induced in the magnet structure during the KSTAR operation was found to be a critical parameter for designing the cooling scheme of the magnet structure as well as defining the requirements of the refrigerator for the cryogenic system. Based on the Joule heating calculation, it was revealed that the bulk temperature rise of the magnet coil structure was less than 1 K. The local maximum temperature especially at the inboard leg of the TF coil structure increased as high as about 21 K for the plasma vertical disruption scenario. For the CS coil structure, the maximum temperature was obtained from the PF fast discharging scenario. This means that the vertical disruption and PF fast discharging scenarios are the major scenarios for the design of TF and CS coil structures, respectively. For the reference scenario, the location of maximum temperature spot changes according to the transient current variation of each PF coil.

• Progress in Superconductivity
• /
• v.8 no.1
• /
• pp.122-126
• /
• 2006

This paper presents experimental and numerical investigation on heat generation of a bulk HTS for application to a 100 kWh Superconductor Flywheel Energy Storage System(SFES) bearing. An experimental device is manufactured to reproduce varying magnetic field conditions that a bulk HTS may experience during the operation of the 100 kWh SFES. The bulk HTS is directly cooled by a cryocooler while the heat is generated by the eddy currents created by varying magnetic fields induced by a coil. In order to design the cryocooling system for the 100 kWh SFES project, a preliminary experiment to investigate the actual cooling load variation under AC magnetic field has been carried out. In the experiment, two different copper holders were designed and tested. Several temperature sensors were installed on each component of the assembly and the temperatures were measured for several operating conditions of the 100 kWh SFES. The experimental investigation on the thermal response of the bulk HTS and its holder is considered to be a valuable step fur the successful materialization of a large-scale SFES.

• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.144-146
• /
• 2005

Dual electromagnetic sensor is used for sensing the weld line. The sensor consists of excitation and two sensing coil wound over the ferro-magnetic core. By using the dual sensor, the effect of noise is minimized. It is based on the generation of eddy currents in the welding plate by passing current through the excitation coil. The sensor can be used to track the butt joints having no gap between them, where a vision based sensor fails to track. Sensor sensitivity depends on the number of coil turns, frequency of excitation, distance of a sensor from the work piece, diameter of core, etc. The whole system consists of a sensor, a signal processing board, a motion controller and a personnel computer (PC). The raw sensor signal is processed using the signal processing board. It consists of amplification, rectification, filtering, averaging, offset adjustment, etc. Based on sensor data, the motion controller adjusts the position of a welding torch.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.3
• /
• pp.1040-1049
• /
• 1996

The high loading combustion is accomplished by making the turbulent intensity strong and the scale small in the premixed combustor. The Da-mkoler number, which is decreased by short turbulent characteristic time or by long chemical reaction time, can make the distributed reaction flame. So we developed a doubled jet burner for high loading combustion. The doubled jet burner was designed to make the scale of the flame small by the effect of impingement and increasing shear stress with doubled jet. We investigated the turbulence characteristics of unburned mixture and visualized several flames with the typical schlieren photography. Then we studied the influence of several factors that related the scale of flame. Consequently, the doubled jet burner can make the eddy very small. And we can obtain the detail information of the flame scale through ADSF(the Average Distance between Successive Fringes) in the micro- schlieren photography. The ADSF is not a exact flame scale, but it has qualitative trend with increasing turbulent intensity. The ADSF is diminished remarkably with increasing turbulent intensity. The reason is that strong turbulent intensity makes the flame zone thick and flamelets numerous. We can confirm this fact by the signal analysis of ion currents.