• 대한기계학회논문집A
• /
• 제26권4호
• /
• pp.739-744
• /
• 2002

This study predicts the modified structural eigenvectors and eigenvalues due to the change in the mass and stiffness of a structure by iterative calculation of the sensitivity coefficient using the original dynamic characteristics. The method is applied to examples of a cantilever and 3 degree of freedom lumped mass model by modifing the mass and stillness. The predicted dynamic characteristics are in good agreement with these from the structural reanalysis using the modified mass and stiffness.

• 대한기계학회논문집A
• /
• 제34권7호
• /
• pp.873-879
• /
• 2010

일반적으로 설계파라미터 변경에 의한 구조물의 동특성변화를 예측하는 연구에 비해 동특성 변화로부터 변경된 설계파라미터를 예측하는 연구는 잘 알려져 있지 않다. 여기에서는 감도계수와 반복법을 사용하여 비례감쇠계의 변경된 설계파라미터를 예측하였다. 감도계수는 변경에 의한 고유벡터의 변화로부터 구하였다. 이 방법을 3 층 전단 구조물에 적용하여 변경된 설계 파라미터를 예측하였으며 재 해석한 결과와 잘 일치함을 알았다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권1호
• /
• pp.48-58
• /
• 2002

There is a purpose of this study for the proposal of the optimum technique utilized for the vibration design initial step. The stiffened plate structure for the ship hull is made for analysis model. To begin with, dynamic characteristics of stiffened plate structure is analysed using FEM. Main vibrational mode of the structure is decided in the analytical result of FEM. The simplified equation on the natural frequency of the main vibrational mode is induced. Next, sensitivity analysis is carried out using the simplified equation, and rate of change of dynamic characteristics is calculated. Then, amount of design variable is calculated using this sensitivity value and optimum structural modification method. The change of natural frequency is made to be an objective function. Thickness of panel, cross section moment of stiffener and girder become a design variable. The validity of the optimization method using simplified equation is examined. It is shown that the result effective in the optimum modification for natural frequency of the stiffened plate structure.

• Smart Structures and Systems
• /
• 제21권5호
• /
• pp.677-686
• /
• 2018

The structural responses are often used to identify the structural local damages. However, it is usually difficult to gain the responses of the track, as the sensors cannot be installed on the track directly. The vehicles running on a track excite track vibration and can also serve as response receivers because the vehicle dynamic response contains the vibration information of the track. A damage identification method using the vehicle responses and sensitivity analysis is proposed for the vehicle-track coupling system in this paper. Different from most damage identification methods of vehicle-track coupling system, which require the structural responses, only the vehicle responses are required in the proposed method. The local damages are identified by a sensitivity-based model updating process. In the vehicle-track coupling system, the track is modeled as a discrete point supported Euler-Bernoulli beam, and two vehicle models are proposed to investigate the accuracy and efficiency of damage identification. The measured track irregularity is considered in the calculation of vehicle dynamic responses. The measurement noises are also considered to study their effects to the damage identification results. The identified results demonstrate that the proposed method is capable to identify the local damages of the track accurately in different noise levels with only the vehicle responses.

• 한국시뮬레이션학회논문지
• /
• 제22권3호
• /
• pp.81-87
• /
• 2013

본 논문은 컴퓨터 해석프로그램인 SimulationX를 이용하여 굴삭기 주행모터의 내부에서 발생하는 서지압력의 저감 방법에 대하여 분석하는 연구이다. 설계민감도 해석을 통하여 설계상의 문제점을 파악하고 해결책에 접근하는 방법을 다룬다. 진행순서는 다음과 같다. 우선 현재 설계 된 주행모터에 장착된 밸브들의 동적거동을 분석하여 설계의 문제점을 찾아낸다. 그 후 많은 설계변수들 중 동적성능향상에 민감하다고 판단되는 변수를 도출하고 설계치수를 조정하여 동적성능 안정화의 경향을 살펴본다. 마지막으로 민감한 변수가 다수 일 경우 변수조합을 통해 효과적인 튜닝방법을 제안한다.

• Structural Engineering and Mechanics
• /
• 제53권2호
• /
• pp.261-276
• /
• 2015

Structural damage and moving load identification are the two aspects of structural system identification. However, they universally coexist in the damaged structures subject to unknown moving load. This paper proposed a dynamic response sensitivity-based model updating method to simultaneously identify the structural damage and moving force. The moving force which is equivalent as the nodal force of the structure can be expressed as a series of orthogonal polynomial. Based on the system Markov parameters by the state space method, the dynamic response and the dynamic response derivatives with respect to the force parameters and elemental variations are analytically derived. Afterwards, the damage and force parameters are obtained by minimizing the difference between measured and analytical response in the sensitivity-based updating procedure. A numerical example for a simply supported beam under the moving load is employed to verify the accuracy of the proposed method.

• 센서학회지
• /
• 제24권2호
• /
• pp.79-82
• /
• 2015

This paper proposes a novel complementary metal oxide semiconductor (CMOS) active pixel sensor (APS) and presents its performance characteristics. The proposed APS exhibits a linear-logarithmic response, which is simulated using a standard $0.35-{\mu}m$ CMOS process. To maintain high sensitivity and improve the dynamic range (DR) of the proposed APS at low and high-intensity light, respectively, two additional nMOSFETs are integrated into the structure of the proposed APS, along with a photogate. The applied photogate voltage reduces the sensitivity of the proposed APS in the linear response regime. Thus, the conversion gain of the proposed APS changes from high to low owing to the addition of the capacitance of the photogate to that of the sensing node. Under high-intensity light, the integrated MOSFETs serve as voltage-light dependent active loads and are responsible for logarithmic compression. The DR of the proposed APS can be improved on the basis of the logarithmic response. Furthermore, the reference voltages enable the tuning of the sensitivity of the photodetector, as well as the DR of the APS.

• 한국자동차공학회논문집
• /
• 제5권1호
• /
• pp.38-48
• /
• 1997

A method for performing kinematic design sensitivity analysis of vehicle suspension systems is presented. For modeling of vehicle suspensions, the multibody dynamic formulation is adopted, where suspensions are assumed as combination of rigid bodies and ideal frictionless joints. In a relative joint coordinate setting, kinematic constraint equations are obtained by imposing cut-joints that transform closed-loop shape suspension systems into open-loop systems. By directly differentiating the constraint equations with respect to kinematic design variables, such as length of bodies, notion axis, etc., sensitivity equations are derived. By solving the sensitivity equations, sensitivity of static design factors that can be used for design improvement, can be obtained. The validity and usefulness of the method are demonstrated through an example where kinematic sensitivity analysis of a MacPherson strut suspension of performed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.837-838
• /
• 2010

• 한국자기공명학회논문지
• /
• 제22권2호
• /
• pp.34-39
• /
• 2018

The Nuclear Magnetic Resonance (NMR) technique using Dynamic Nuclear Polarization (DNP) procedures is one of the promising techniques that enable overcoming low sensitivity problems in NMR spectroscopy. We constructed an ODNP-NMR system using a commercial benchtop EPR spectrometer. The $^1H$ NMR peak area of water in aqueous solutions of 4-hydroxy-TEMPO was enhanced more than 95 times in the ODNP-NMR experiments. Our signal enhancement results were about 55% of the previously reported result. This could be due to non-uniform microwave power over a sample and unwanted sample heating by microwave. However, this portable ODNP-NMR spectrometer will be eventually useful for site-specific detection with nano-scale spatial resolutions and molecular dynamics studies with significantly improved signal sensitivity.