• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.2
• /
• pp.161-166
• /
• 2010

Elastomeric seals are widely used in dynamic seal applications, and it is well known that the sealing surfaces can be gradually worn out. Abrasive wear is known to be the most dominant factor; however, little research has been carried out on this problem until now. In this study, a new contact problem related to elastomeric seals-a small spherical particle and steel surface-was modeled and analyzed using MARC. Variations of von-Mises and residual stress distributions as well as deformed seal and steel surface shapes with seal materials and interferences are presented. The stress distribution and surface deformation are highly affected by the elastic properties of seal. For PTFE, the maximum von-Mises stress exceeds the yield strength, and plastic deformation occurs on the steel surface. Therefore, the sealing surface can also be worn down by sub-surface fatigue due to intervening hard particles in the sealing surfaces together with the well-known abrasion.

• Journal of the Korean Ceramic Society
• /
• v.44 no.4 s.299
• /
• pp.194-197
• /
• 2007

Polyacrylonitrile (PAN)/$Fe_2O_3$ nanocomposite membranes with a thickness of 0.02 mm were electrospun by adding 0 to 5 wt% of $Fe_2O_3$ into PAN. The surface tension, density, kinematic viscosity and dynamic viscosity of the PAN solution were determined to be $33.8{\pm}1mN/m$, 0.9794 g/ml, $1548.6mm^2/sec$ and 1516.7 cP, respectively. The average diameters of PAN fibers containing 0, 1 2, 3, and 4 wt% $Fe_2O_3$ particles were 300, 260, 210, 130, and 90 nm, respectively. Fourier-transform infrared spectroscopy results showed that the addition of $Fe_2O_3$ nanoparticles to the PAN mat reduced the absorption peak intensity at $2242cm^{-1}$ ($C{\equiv}N$ bond) while it caused a sharp increase in the peak intensity at $2356cm^{-1}$(C=O bond). Thus, it appears that an appropriate amount of $Fe_2O_3$ nanoparticles in the PAN backbone leads to an improvement of the performance of the $CO_2$ gas sensor, most likely due to the change of functional groups in the membrane.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.8
• /
• pp.775-782
• /
• 2010

This study is performed to study the effect of the tray in the absorber of a flue-gas desulphurization (FGD) system by using a computational fluid dynamic (CFD) technique. Stagnant time of slurry and the pressure drop in the FGD absorber increase when a tray is used in the absorber. Stagnant time of slurry results in an increase in the desulfurization effect and a decrease in the power of the absorber recirculation pump; however, increased pressure drop requires more power of booster fan in the FGD system should be increased. The gas and slurry hydrodynamics inside the absorber is simulated using a commercial CFD code. The continuous gas phase has been modeled in an Eulerian framework, while the discrete liquid phase has been modeled by adopting a Lagrangian approach by tracking a large number of particles through the computational domain. It was observed that the power saved upon increasing the stagnant time of slurry was more than increased power with pressure drop.

• Journal of Sensor Science and Technology
• /
• v.10 no.2
• /
• pp.118-124
• /
• 2001

When particles are dissolved in solution, they have different zeta-potentials depending on pH. Zeta-potential has an influence on particle separation, which can control particle size. And the size of $WO_3$ particle affects the sensitivity of $WO_3$ sensor for detecting NO gas. Therefore we study influence of pH on NO-sensing $WO_3$ gas sensor fabricated by Sol-Coprecipitation method. As pH increases from 2 to 7, dynamic mobility of $WO_3$ precursor was increased. When pH was 7, it showed the largest distribution separation. It means when pH is 7, we can make $WO_3$ powder which has smaller particle size. And it is confirmed by particle size analysis of $WO_3$ powder, X-ray diffration result of $WO_3$ sensing layer and surface morphology. It also affect NO sensing characteristics of $WO_3$ gas sensor. The sensing film synthesized at pH 7 showed the largest sensitivity.

• Applied Chemistry for Engineering
• /
• v.10 no.8
• /
• pp.1136-1140
• /
• 1999

Melt blends of polymide 6(PA6) and polypropylene grafted maleic anhydride(PP-g-MA) were prepared to study the influence of chemical reaction between the two polymer components. The tensile, flexural, izod impact, dynamic mechanical properties and phase structure were investigated for this blend system. Tensile strength and modulus of the blends showed synergetic effect upon blending of two polymer components. Flexural properties maintained the value of numerical mean calculated from the weight ratio of two components. Also, notched izod impact strengths showed maximum in th PA6/PP-g-MA 50/50 wt % blend. From the change of tan ${\delta}$ observed, we confirmed the increase of miscibility in this blend system by chemical reaction between PA6 and PP-g-MA. Blends of good impact resistance could be obtained when the PP-g-MA particles of $2{\mu}m$ was dispersed in the PA6 matrix.

• Journal of the Korean Ceramic Society
• /
• v.36 no.7
• /
• pp.742-750
• /
• 1999

Nanosized TiO2 powders were synthesized using the chemical vapor conduensation (CVC) process with various precursor feeding rates (0.37 and 0.752 ml/min) and oxygen flow rates(1-2slm) conditions and powder characteristics were investigated in terms of formation of nanosized powder varying with the above processing conditions. For this study the main thermodynamic and fluid dynamic factors -supersaturation ratio collision frequency and residence time-were theoretically established and compared to the characteristics of formed TiO2 powder. The loosely combined anatase phase powders (including less than 3%of rutile phase) having 20-30nm crystallite size were obtained at overall conditions. The particle size and th degree of agglomeration for a precursor flow rate of 0.376 ml/min turn out to be smaller than for a flow rate of 0.742ml/min. And the decreasing of particles size and particle size distribution were observed with increasing oxygen flow rate as the residence time and collision frequency were reduced by increasing oxygen flow rate,. It appears that further scrutiny is needed to elucidate the influence of the individual thermodynamic and kinetic parameters mdependently.

• Journal of KIISE
• /
• v.42 no.2
• /
• pp.190-202
• /
• 2015

Much research has been conducted on location-based intelligent personal assistants that can understand a user's intention by learning the user's route model and then inferring the user's destinations and routes using data of GPS and other sensors in a smartphone. The intelligence of the location-based personal assistant is contingent on the accuracy and efficiency of the real-time predictions of the user's intended destinations and routes by processing movement information based on uncertain sensor data. We propose a robust particle filter based on Dynamic Bayesian Network model to infer the user's routes. The proposed robust particle filter includes a particle generator to supplement the incorrect and incomplete sensor information, an efficient switching function and an weight function to reduce the computation complexity as well as a resampler to enhance the accuracy of the particles. The proposed method improves the accuracy and efficiency of determining a user's routes and destinations.

• Journal of the Society of Naval Architects of Korea
• /
• v.51 no.5
• /
• pp.409-418
• /
• 2014

Simulation of flow past a complex marine structure requires a fine resolution in the vicinity of the structure, whereas a coarse resolution is enough far away from it. Therefore, a lot of grid cells may be wasted, when a simple Cartesian grid system is used for an Immersed Boundary Method (IBM). To alleviate this problems while maintaining the Cartesian frame work, we adopted an Adaptive Mesh Refinement (AMR) scheme where the grid system dynamically and locally refines as needed. In this study, We implemented a moving IBM and an AMR technique in our basic 3D incompressible Navier-Stokes solver. A Volume Of Fluid (VOF) method was used to effectively treat the free surface, and a recently developed Lagrangian Dynamic Subgrid-scale Model (LDSM) was incorporated in the code for accurate turbulence modeling. To capture vortex induced vibration accurately, the equation for the structure movement and the governing equations for fluid flow were solved at the same time implicitly. Also, We have developed an interface by using AutoLISP, which can properly distribute marker particles for IBM, compute the geometrical information of the object, and transfer it to the solver for the main simulation. To verify our numerical methodology, our results were compared with other authors' numerical and experimental results for the benchmark problems, revealing excellent agreement. Using the verified code, we investigated the following cases. (1) simulating flow around a floating sphere. (2) simulating flow past a marine structure.

• Korean Journal of Food Science and Technology
• /
• v.25 no.3
• /
• pp.210-213
• /
• 1993

The purpose of this research was to investigate fluidization characteristics of three solid particles, correlations between voidage and superficial velocity. The inside diameter of a column did not affect the fraction void-superficial velocity relationship for fluidization systems which was obtained as follows: $\frac{u}{u_t}={\varepsilon}^{3.703}----Sea\;Sand$ $\frac{u}{u_t}={\varepsilon}^{3.5665}----long\;Exchange$ $\frac{u}{u_t}={\varepsilon}^{4.066}----GAC$ And the sphericial type media is good for fluidized systems as it maintains low voidage. Actually, if biofilm attached to media (bioparticle), the density became lower in fluidized bed biofilm reactor. Therefore, as the density of media become higher, it is easy to maintain fluidized beds.

• YAKHAK HOEJI
• /
• v.51 no.1
• /
• pp.13-34
• /
• 2007

Traditional Medicine (TM) is called as philosophical medicine in Korea. An unified theory named as Sihnsang-hanron (SSHR) was hypothesized through studies of scientific analyses on various theories of TM. SSHR has extracted seven concepts which are six common ones from the great three books (三大原典) and the Logic of Laotzu & Chuangtzu (老莊思想). Six common concepts are the affecting by cold (傷寒), qi (氣), cold or heat (寒熱), exterior & interior of body (表裏), deficiency or excessiveness (虛實), and yin & yang (陰陽). We have tried to apply these seven concepts to Physics and Life Science. The affecting by cold means anti-sunlight and the origin of all diseases. The difference between TM and modern medical science would be in diagnostic methods as well as their theoretical analyses for various diseases. The modern science follows Haeckel's positive dialectics applied by the biological monism, and oriental one(SSHR) does Yin-Yang monism from the studies of Logic of Laotzu (老子) & Chuangtzu (莊子). SSHR would make the theory of exterior & interior of body (表裏論) and six channels (六經) develope scientifically as a diagnostic technique of disease. This theory is an excellent one that can't be found out in modern medical science, and so it should be developed as a scientific theory by using modern mechanic instrument. Chuangtzu asserted that ai was the basic substance of the universe. It is hypothesized that qi (氣) is like small particles -higgs, with dynamic power in modern Physics. We consider cautiously qi could be calculated by mathematics through higgs' bosons in near future.