• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.1
• /
• pp.8-11
• /
• 2019

In this paper, a Ku-band 50-W internally-matched power amplifier is designed and fabricated using a CGHV1J070D GaN HEMT from Wolfspeed. To obtain the same magnitudes and phases for the output signals of the unit transistor cells, which constitute a power transistor, a slit pattern and an asymmetric T-junction are used in the input and output matching circuits. The internally-matched power amplifier is fabricated on two different thin-film substrates with relative dielectric constants of 40 and 9.8, respectively, and is measured under pulsed conditions with a pulse period of $330{\mu}s$ and a duty cycle of 6%. The measured results show a maximum output power of 50~73 W, a drain efficiency of 35.4~46.4%, and a power gain of 4.5~6.5 dB from 16.2 to 16.8 GHz.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.569-572
• /
• 2014

This paper presents a CMOS switched-capacitor interface circuit for MEMS capacitive sensors. It consist of a capacitance to voltage converter(CVC), a second-order ${\Sigma}{\Delta}$ modulator, and a comparator. A bias circuit is also designed to supply constant bias voltages and currents. This circuit employes the correlated-double-sampling(CDS) and chopper-stabilization(CHS) techniques to reduce low-frequency noise and offset. The designed CVC has a sensitivity of 20.53mV/fF and linearity errors less than 0.036%. The duty cycle of the designed ${\Sigma}{\Delta}$ modulator output increases about 5% as the input voltage amplitude increases by 100mV. The designed interface circuit shows linearity errors less than 0.13%, and the current consumption is 0.73mA. The proposed circuit is designed in a 0.35um CMOS process with a supply voltage of 3.3V. The size of the designed chip including PADs is $1117um{\times}983um$.

• Journal of the Korean institute of surface engineering
• /
• v.54 no.2
• /
• pp.53-61
• /
• 2021

The properties of tetrahedral amorphous Carbon (ta-C) film can be determined by multiple parameters and comprehensive effects of those parameters during a deposition process with filtered cathodic vacuum arc (FCVA). In this study, Taguchi method was adopted to design the optimized FCVA deposition process of ta-C for improving deposition efficiency and mechanical properties of the deposited ta-C thin film. The influence and contribution of variables, such as arc current, substrate bias voltage, frequency, and duty cycle, on the properties of ta-C were investigated in terms of deposition efficiency and mechanical properties. It was revealed that the deposition rate was linearly increased following the increasing arc current (around 10 nm/min @ 60 A and 17 nm/min @ 100A). The hardness and I_D/I_G showed a correlation with substrate bias voltage (over 30 GPa @ 50 V and under 30 GPa @ 250 V). The scratch tests were conducted to specify the effect of each parameter on the resistance to plastic deformation of films. The analysis on variances showed that the arc current and substrate bias voltage were the most effective controlling parameters influencing properties of ta-C films. The optimized parameters were extracted for the target applications in various industrial fields.

• Journal of Biomedical Engineering Research
• /
• v.43 no.1
• /
• pp.1-10
• /
• 2022

Non-alcoholic fatty liver disease(NAFLD) is excessive hepatic lipid accumulation mainly caused by obesity. This study aimed to evaluate whether micro-current stimulation(MCS) could modulate lipid metabolism regarding the Sirt1/AMPK pathway, fatty acid β-oxidation pathway, and lipolysis and lipogenesis-related factors in FL83B cells. For the NAFLD cell model, FL83B cells were treated with oleic acid for lipid accumulation. MCS were stimulated for 1 hr and used frequency 10 Hz, duty cycle 50%, and biphasic rectangular current pulse. The intensity of MCS was divided into 50, 100, 200, and 400 ㎂. Through the results of Oil red O staining, it was confirmed that MCSs with the intensity of 200 ㎂ and 400 ㎂ significantly reduced the degree of lipid droplet formation. Thus, these MCS intensities were applied to western blot analysis. Western blot analysis was performed to analyze the effects of MCS on lipid metabolism. MCS with the intensity of 400 ㎂ showed that significantly activated the Sirt1/AMPK pathway, a key pathway for regulating lipid metabolism in hepatocytes, and fatty acid β-oxidation-related transcription factors. Moreover, it activated the lipolysis pathway and suppressed lipogenesis-related transcription factors such as SREBP-1c, FAS, and PPARγ. In the case of MCS with the intensity of 200 ㎂, only PGC1α and SREBP-1c showed significant differences compared to cells treated only with oleic acid. Taken together, these results suggested that MCS with the intensity of 400 ㎂ could alleviate hepatic lipid accumulation by modulating lipid metabolism in hepatocytes.

• Journal of Internet of Things and Convergence
• /
• v.9 no.3
• /
• pp.61-67
• /
• 2023

In order to optimize the pulse electroforming copper process, a double hidden layer BP (Back Propagation) neural network is constructed. Through sample training, the mapping relationship between electroforming copper process conditions and target properties is accurately established, and the prediction of microhardness and tensile strength of the electroforming layer in the pulse electroforming copper process is realized. The predicted results are verified by electrodeposition copper test in copper pyrophosphate solution system with pulse power supply. The results show that the microhardness and tensile strength of copper layer predicted by "3-4-3-2" structure double hidden layer neural network are very close to the experimental values, and the relative error is less than 2.32%. In the parameter range, the microhardness of copper layer is between 100.3~205.6MPa and the tensile strength is between 112~485MPa.When the microhardness and tensile strength are optimal,the corresponding process conditions are as follows: current density is 2A-dm-2, pulse frequency is 2KHz and pulse duty cycle is 10%.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.12
• /
• pp.1129-1135
• /
• 2013

In this, three types of natural gas were employed to investigate the effect of low-calorific natural gas on the performance of and emissions from a heavy-duty CNG engine. The performance and emission characteristics were analyzed by conducting a full-load test, WHSC mode test, and WHTC mode test. The results showed that the torque of low-calorific natural gas with $9,800kcal/Nm^3$ of higher heating value decreased by 4.4 compared to that of the current natural gas with $10,400kcal/Nm^3$ of heating value. With low-calorific fuels, CO, $CO_2$, and $NO_x$ emissions decreased. However, THC emissions increased. According to the WHSC and WHTC mode test results, the thermal efficiency increased and the emission characteristics showed a similar trend to the full-load test results. Low-calorific natural gases cause a decrease in torque at full-load operation conditions and an increase in hydrocarbon emissions.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.2
• /
• pp.217-224
• /
• 2012

In general, transportation sources include both on-road vehicles and off-road equipment. Off-road vehicles have usually used diesel engines, which have the disadvantage of high NOx emission. Common rail direct injection (CRDI) and after-treatment systems have been applied to meet the exhaust gas emission regulations for diesel vehicles. In the present, agricultural machinery has satisfied the Tier 3 emission regulations by using waste gate turbocharger (WGT) and internal exhaust gas recirculation (EGR). In this paper, the combustion and emission characteristics of an EGR system applied to a 56kW off-road vehicle in non-road transient cycle (NRTC) mode have been investigated. The EGR map was made from foundation experiments determining the EGR duty for all engine operating conditions, and then this map was applied to the NRTC mode. Consequently, the NOx emission was reduced by the EGR system, and the Tier 4 interim emission regulations were satisfied by using both the EGR system and an after-treatment system.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.9
• /
• pp.63-73
• /
• 2015

This work proposes a 2-channel time-interleaved (T-I) 10b 120MS/s pipeline SAR ADC minimizing offset mismatch between channels without any calibration scheme. The proposed ADC employs a 2-channel SAR and T-I topology based on a 2-step pipeline ADC with 4b and 7b in the first and second stage for high conversion rate and low power consumption. Analog circuits such as comparator and residue amplifier are shared between channels to minimize power consumption, chip area, and offset mismatch which limits the ADC linearity in the conventional T-I architecture, without any calibration scheme. The TSPC D flip-flop with a short propagation delay and a small number of transistors is used in the SAR logic instead of the conventional static D flip-flop to achieve high-speed SAR operation as well as low power consumption and chip area. Three separate reference voltage drivers for 4b SAR, 7b SAR circuits and a single residue amplifier prevent undesirable disturbance among the reference voltages due to each different switching operation and minimize gain mismatch between channels. High-frequency clocks with a controllable duty cycle are generated on chip to eliminate the need of external complicated high-frequency clocks for SAR operation. The prototype ADC in a 45nm CMOS technology demonstrates a measured DNL and INL within 0.69LSB and 0.77LSB, with a maximum SNDR and SFDR of 50.9dB and 59.7dB at 120MS/s, respectively. The proposed ADC occupies an active die area of 0.36mm2 and consumes 8.8mW at a 1.1V supply voltage.

• The Korean Journal of Elementary Counseling
• /
• v.9 no.2
• /
• pp.175-193
• /
• 2010

The aim of this study is to examine effects of a yoga program for children on school stress of the elementary school children. To achieve this goal, total 10 students out of 231 in 6 classes among the third graders in M elementary school in B city were selected as subjects for this study. After regular school hours, they participated in a children's yoga program for 16 times for 45 minutes per session in the course of 8 weeks. An ethnographic interview was conducted to identify the effects of the program. During the initial stage of the children's yoga program, the participants were interviewed preliminarily. An analysis of areas and an analysis of classifications were made based on the initial interview results, and an area classification table was drawn on the school stress perceived by the elementary school children. After the yoga program ended, a follow up interview was made to apply an analysis of components by comparing changes in the school stress level due to a yoga effect. A research report was written through a cycle of addition and supplement in which the previous data analysis was complemented and corrected by new findings of the study. As a result of the ethnographic interview to analyze the school stress perceived by the elementary school children, and an examination of the changes in the school stress level, the children's yoga program proved to be significantly effective in reducing the school stress. However there were limitations to a certain degree in stress reduction. Details of such findings in each sub-category are as follow. First, as a result of the initial interview analysis, the school stress was classified broadly into 4 categories of study stress, friendship stress, teacher stress, and school environment stress. Second, the study stress as the first category of the school stress was classified into 3 sub-categories of homework, class, and exam stresses. In spite of minor differences among 3 sub-categories, the stress was reduced in general. Third, the friendship stress as the second category of the school stress was also classified into 3 sub-categories of bullying, alienation, and performing one's duty. There were minor differences among sub-categories, however stress reduction also appeared with the exception of the performing one's duty category which had relatively little effect from the yoga program. Fourth, regarding the teacher stress as the third school stress, a classification was made into 3 sub-categories of preference, penalty, and teaching method. Minor differences among the 3 sub-categories notwithstanding, stress reduction appeared with the exception of the teaching method stress which had relatively little effect from the yoga program. Fifth, the school environment stress as the fourth category of the school stress was classified into 2 sub-categories of school meals and facilities. Minor differences between the 2 categories notwithstanding, stress reduction appeared with the facilities stress having relatively little effect.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.134-134
• /
• 2015

최근 액체 플라즈마에 대한 주된 이슈는 방전에 의해 발생하는 히드록실라디칼(OH-)과 버블이다. 액체 플라즈마를 이용한 다양한 응용분야에서는 히드록실라디칼에 주목하고 있다. 액체 플라즈마는 그래핀 파생물의 용액 친화도 향상을 위해 이용될 수 있다. 흑연이 포함된 과산화수소(H2O2) 용액에서 전기적인 방전으로 만들어진 히드록실라디칼로 그래핀 파생물의 용액 친화도를 향상시킨다. 이는 잠재적인 프린팅(printing) 기술 발전에 기대된다. 그리고 이 라디칼은 폐수에서 발암성의 트라이클로로아세트산(CCl3COOH)을 탈 염소하고 분해하는 역할을 하여 액체 플라즈마가 새로운 수처리 기술로 부상되고 있다. 또한 인체에서는 살균 작용을 하는 것 뿐만 아니라 단백질 고리를 끊는 역할을 하여 전립선 수술과 같은 인체수술에 적용될 수 있다. 최근 액체 플라즈마를 이용한 돼지 각막 임상수술에서 레이저와 필적할 정도로 매우 정밀하게 수술된 연구결과가 발표되어 인체 각막수술 적용에 기대된다. 이처럼 액체 플라즈마를 이용한 대부분의 응용분야에서 히드록실라디칼의 역할이 중요하다. 액체 플라즈마의 또 다른 이슈인 버블은 2가지의 역할을 한다. 첫 번째로 방전소스의 역할이다. 액체 속에 담긴 얇은 전극에 전압을 인가하면 전극 주변에서 강한 전기장의 발생으로 줄열(joule heating)에 의해 버블이 생성된다. 전극에서 버블이 생성되었을 때, 서로 다른 유전율을 가진 두 물질로 나누어진다. (버블 안은 공기로 상대 유전율 ${\varepsilon}r{\fallingdotseq}=1$, 용액은 ${\varepsilon}r{\fallingdotseq}=80$이다.) 시스템에 인가된 전압이 항복 전압(breakdown voltage)을 넘어서면 유전율이 상대적으로 낮은 버블내부에 강한 전기장이 걸리게 되어 방전이 일어난다. 만약 버블이 존재하지 않는다면 방전을 위해서 매우 높은 전압이 필요하다. 따라서 버블은 플라즈마 방전의 소스역할을 한다. 두번째로 버블은 전극의 부식을 방지하는 역할을 한다. 전극 부식은 주로 전기분해로 인한 산화반응에 의해 발생하는데 버블을 전극에 오래 머무르게 하면 부식을 방지할 수 있다. 이처럼 액체 플라즈마 시스템에서 버블의 역할들은 상당히 중요하다. 일반적으로 버블은 시스템에 인가하는 전원, 전극 극성 그리고 전압크기에 따라 거동이 달라진다. 시스템에 AC파워를 인가하면 버블은 주파수가 높을수록 전극에서 떨어지는 속도가 빨라지는 특성을 보인다. 핀 전극 극성이 음극일 때는 양극일 때보다 버블이 더 잘 생성된다. 또한 인가전압크기에 따라 거동이 달라지며 시스템에 같은 전압을 인가하여도 크기가 항상 같지 않고, 거동도 일관성을 보이지 않은 랜덤적인 모습을 보인다. 본 연구에서는 이 랜덤적인 버블의 거동을 정리하고 응용분야에서 중요하게 여기는 히드록실라디칼 생성에 대해 공부하기 위해 염류 용액(saline solution)에 핀(pin)-면(plane) 전극 구조를 설치하여 10Hz 주파수(1% duty cycle)를 가진 0-600V 구형펄스로 실험하였다. 실험을 통한 결과로서 랜덤적인 버블의 거동을 전극에서 버블이 떨어지는 속도와 플라즈마 특성에 따라 슈팅모드(shooting mode)와 유지모드(keeping mode) 2가지 모드로 분류하였다. 슈팅모드에서는 버블이 핀 전극에서 성장하지 못하고 빠른 속도로 떨어지는 모드로 플라즈마 방전이 잘 이루어지지 않는다. 반면 유지모드에서는 버블이 핀 전극에서 떨어지지 않고 지속적으로 성장한다. 이 모드에서는 펄스 시간 동안 하나의 버블로 연속적인 방전이 가능하다. 방전이 일어날 때 발생하는 히드록실라디칼의 생성은 버블 내부의 쉬스와 관련이 있다. 이 라디칼을 만들기 위해서는 높은 에너지가 요구되기 때문에 버블 내부의 쉬스(sheath)에서 만들어진다. 펄스 동안 쉬스는 주로 핀 전극 주변에서 유지되며 히드록실라디칼은 이곳에서 주로 만들어진다. 따라서 버블과 함께 쉬스도 성장하는 버블유지모드에서 슈팅모드보다 히드록실라디칼이 더 많이 생성된다.