• 한국전산구조공학회논문집
• /
• 제26권1호
• /
• pp.49-57
• /
• 2013

일반교량은 상부구조, 연결부분, 하부구조 및 기초로 구성되어 있고 내진성능은 하부구조와 연결부분의 파괴메카니즘에 의해 결정된다. 그러므로 내진설계는 구조부재의 설계강도, 즉 설계단면을 결정하는 기본설계단계에서 수행되어야 한다. 도로교설계기준 내진설계편은 두 가지 기본설계 방식을 제시하고 있다. 첫째는 기존 설계방식으로 내진설계편이 제시한 응답수정계수를 적용하는 방식이고 둘째는 새로 도입된 연성도 내진설계 방식으로 설계자가 응답수정계수를 결정하는 방식이다. 이 연구에서는 일반교량을 대상으로 두 설계방식을 같이 적용하는 기본설계를 수행하고 내진성능 확보의 관점에서 요구되는 보완사항을 제시하였다.

• 한국전산구조공학회논문집
• /
• 제27권3호
• /
• pp.163-172
• /
• 2014

일반교량 내진설계의 목적은 붕괴방지설계이고 도로교설계기준 내진설계편은 교량구조의 연성파괴메카니즘을 구성하는 설계방식을 제시하고 있다. 그러나 구조형식 또는 현장여건에 의해 연성파괴메카니즘을 구성하는 것이 비합리적인 경우 차선책으로 취성파괴메카니즘을 구성하여 붕괴방지설계를 수행할 수 있다. 연성파괴메카니즘을 구성하는 기존 설계방식과 함께 내진설계편은 연성도 내진설계를 부록으로 제시하고 있다. 연성도 내진설계는 철근콘크리트 교각으로 구성되는 교량에 적용하며 설계자가 하부구조의 소요응답수정계수를 결정하고 이로부터 심부구속철근을 설계하는 방식이다. 이 연구에서는 철근콘크리트 교각기둥과 강재받침으로 설계된 일반교량을 선정하여 기존 설계방식과 연성도 내진설계를 모두 적용한 결과로부터 차이점을 확인하고 설계자가 내진설계를 수행하는 과정에서 두 설계방식을 모두 고려하는 설계절차를 제안하였다.

• 한국강구조학회 논문집
• /
• 제9권1호통권30호
• /
• pp.95-105
• /
• 1997

Structures subjected to strong seismic excitation may undergo inelastic deformation cycles. The resulting cumulative fatigue damage process reduces the ability of structures and components to withstand seismic loads. Yet, the present earthquake resistance design methods focus mainly on the maximum displacement ductility, ignoring the effect of the cyclic responses. The damage parameters closely related to the cumulative damage need to be properly reflected on the aseismic design methods. In this study, two cumulative damage assessment methods derived from the plastic fatigue theory are investigated. The one is based on the hysteretic ductility amplitude, and the other is based on the dissipated hysteretic energy. Both methods can consider the maximum ductility and the cyclic behavior of structural response. The validity of two damage methods has been examined for single degree of freedom structures with various natural frequencies against two different earthquake excitations.

• Earthquakes and Structures
• /
• 제2권2호
• /
• pp.127-147
• /
• 2011

In a companion paper as well as in earlier publications, it has been shown that in asymmetric frame buildings, designed in accordance with modern codes and subjected to strong earthquake excitations, the ductility demands at the so called "flexible" edges are consistently and substantially higher than the ductility demands at the "stiff" edges of the building. In some cases the differences in the computed ductility factors between elements at the two opposite building edges exceeded 100%. Similar findings have also been reported for code designed reinforced concrete buildings. This is an undesirable behavior as it indicates no good use of material and the possibility for overload of the "flexible" edge members with a consequent potential for premature failure. In the present paper, a design modification will be introduced that can alleviate the problem and lead to a more uniform distribution of ductility demands in the elements of all building edges. The presented results are based on the steel frames detailed in the companion paper. This investigation is another step towards more rational design of non-symmetric steel buildings.

• Earthquakes and Structures
• /
• 제2권2호
• /
• pp.109-126
• /
• 2011

The inelastic earthquake response of non-symmetric, braced steel buildings, designed according to the EC3 (steel structures) and EC8 (earthquake resistant design) codes, is investigated using 1, 3 and 5-story models, subjected to a set of 10, two-component, semi-artificial motions, generated to match the design spectrum. It is found that in these buildings, the so-called "flexible" edge frames exhibit higher ductility demands and interstory drifts than the "stiff" edge frames. We note that the same results were reported in an earlier study for reinforced concrete buildings and are the opposite of what was predicted in several other studies based on the over simplified, hence very popular, one-story, shear-beam type models. The substantial differences in such demands between the two sides suggest a need for reassessment of the pertinent code provisions. In a follow up paper, a design modification will be introduced that can lead to a more uniform distribution of ductility demands in the elements of all building edges. This investigation is another step towards more rational design of non-symmetric steel buildings.

• 한국전산구조공학회논문집
• /
• 제29권2호
• /
• pp.187-192
• /
• 2016

일반설계에서 탄성거동을 전제로 구조물을 설계하는 것과 달리 내진설계는 구조물의 소성거동을 규명하고 조정하여 붕괴를 방지하는 것이 목적이다. 일반교량의 경우에 요구되는 붕괴방지수준은 교량의 특정한 구조부재의 소성거동으로 낙교를 방지하여 지진발생 이후에 긴급차량의 통과를 가능하게 하는 것이다. 이러한 소성거동은 연결부분 또는 교각기둥에 제한되고 각 경우에 적절한 조치가 요구된다. 도로교설계기준은 교각기둥에서 소성힌지를 형성하여 연성붕괴기구를 구성하는 설계방식과 함께 철근콘크리트 교각을 하부구조로 하는 교량을 대상으로 연결부분의 항복을 이용하여 취성붕괴기구를 구성하는 연성도 내진설계를 부록으로 제시하고 있다. 이 연구에서는 철근콘크리트 교각기둥과 강재받침으로 설계된 일반교량을 선정하고 연성붕괴기구와 취성붕괴기구를 모두 고려한 붕괴방지 설계절차 및 도로교설계기준에 요구되는 수정사항을 제안하였다.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2006년도 학술발표회 논문집
• /
• pp.276-283
• /
• 2006

Korea is considered to be immune from the earthquake hazard because it is located far away from the active fault. However, recent earthquake caused a loss of lives and economical loss worldwide. Hence there has been raised an importance of the earthquake resistant design for various infrastructures. In this research, the seismic design and evaluation criterion for RC bridge pier were proposed from the experimental results of 82 circular RC bridge piers tested in domestic and aboard. New seismic criterion was introduced the limited ductile design provision suitable to Korean peninsula, which would be classified as a low or moderate seismic region. In addition, further important topic for the seismic safety of RC bridge piers in Korea is the seismic performance enhancement of RC bridge piers, which were designed and constructed before the 1992 seismic design provision. Therefore, the proposed seismic performance evaluation criterion could be very useful to judge seismic retrofit need or not according to the residual seismic performance of the RC bridge piers. Also, it could reduce an uncertainty for the safety of the infrastructure under earthquakes.

• Structural Engineering and Mechanics
• /
• 제32권5호
• /
• pp.587-608
• /
• 2009

Modern earthquake-resistant design aims to isolate architectural precast concrete panels from the structural system so as to reduce the interaction with the supporting structure and hence minimize damage. The present study seeks to maximize the cladding-structure interaction by developing an energy-dissipating cladding system (EDCS) that is capable of functioning both as a structural brace, as well as a source of energy dissipation. The EDCS is designed to provide added stiffness and damping to buildings with steel moment resisting frames with the goal of favorably modifying the building response to earthquake-induced forces without demanding any inelastic action and ductility from the basic lateral force resisting system. Because many modern building facades typically have continuous and large openings on top of the precast cladding panels at each floor level for window system, the present study focuses on spandrel type precast concrete cladding panel. The preliminary design of the EDCS was based on existing guidelines and research data on architectural precast concrete cladding and supplemental energy dissipation devices. For the component-level study, the preliminary design was validated and further refined based on the results of nonlinear finite element analyses. The stiffness and strength characteristics of the EDCS were established from a series of nonlinear finite element analyses and are discussed in detail in this paper.

• 한국강구조학회 논문집
• /
• 제16권6호통권73호
• /
• pp.793-805
• /
• 2004

본 연구에서는 철골 연성 모멘트 골조에 대하여 반응수정계수(R)의 핵심 구성요소인 연성계수 및 강도계수를 평가하였다. 철골 연성 모멘트 골조에 대한 연성계수($R_{{\mu},MDOF}$) 는 단자유도 구조물에 대한 연성계수($R_{{\mu},SDOF}$)에 다자유도 보정계수($R_M$)를 곱하여 산정하였다. 단자유도 구조물에 대한 연성계수($R_{{\mu},SDOF}$)는 지진하중을 받는 탄소성 단자유도(SDOF) 구조물의 목표 변위 연성비와 주기에 따른 비선형 동적해석으로부터 산정하였다. 통계적 연구와 회귀분석으로부터 연성계수를 산정하기 위한 평가식이 제시되었다. 다자유도의 영향을 고려하기 위한 보정계수($R_M$)는 기존의 연구결과로보터 회귀분석을 이용하여 구하였다. 철골 연성 모멘트 골조에 대한 강도계수는 비선형 정적해석으로부터 산정하였다. 철골 연성 모멘트 골조의 연성 계수 및 강도계수를 평가하기 위하여, 구조물의 층수(4, 8 및 16층), 지진구역계수(Z=0.075, 0.2 및 0.4), 골조 시스템(외곽골조 및 분배골조) 및 붕괴 메카니즘(강기둥-약보 및 약기둥-강보)을 설계 매개변수로 하여 총 36개의 예제구조물을 설계하였다. 철골 연성 모멘트 골조의 연성계수 및 강도계수에 이러한 설계 매개변수가 미치는 영향을 분석하였다.

• Steel and Composite Structures
• /
• 제35권4호
• /
• pp.527-544
• /
• 2020

This research presents the design and numerical assessment of composite steel-concrete frame structures with welded dissipative fuses. The assessment has been carried out based on linear response spectrum, nonlinear static pushover and time history procedures. The analytical expressions which define the envelope of the nonlinear response of the dissipative fuses are first presented and calibrated against experimental results available in literature. The assessment is then carried out according to a design methodology proposed herein. Outcomes of the numerical assessment indicate that the use of welded dissipative fuses successfully limited damage within the replaceable parts. Furthermore, although structures with dissipative fuses present lower strength and, generally, lower displacement capacity, their displacement ductility and global dissipative performance are generally higher than conventional structures, especially when the structure with dissipative fuses presents a dissipative configuration adjusted to the bending moment distribution diagram calculated for the applied seismic action.