• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.23 no.2
• /
• pp.51-56
• /
• 2015

This paper presents the procedure of drag prediction for EAV-1, based on a numerical analysis correlated to an in-flight test. EAV-1, developed by Korea Aerospace Research Institute, is a small-sized UAV to test a hydrogen-fuel cell power system. The long-endurance test flight of 4.5 hours provides numerous in-flight data. The thrust and drag of EAV-1 during the flight test are estimated based on the wind-tunnel test results for EAV-1's propeller performance. In addition, the CFD analysis using a commercial Navier-Stokes code is carried out for the full-scale EAV-1. The computational result suggests that the initial CFD analysis substantially under-predicts the in-flight drag in that the discrepancy is up to 27.6%. Therefore, additional investigation for more accurate drag prediction is performed; the effect of propeller slipstream is included in the CFD analysis through "fan disk" modelling. Also, the additional drag from airplane trim and load factor that actually exists during the flight test in a circular path is considered. These supplemental analyses for drag prediction turn out to be effective since the drag discrepancy reduces to 2.3%.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.12 no.6
• /
• pp.711-718
• /
• 2009

During the preliminary design phase of a supersonic aircraft, it is necessary to evaluate many potential engine/airframe combinations to determine the best solution to given set of mission requirements. And it is very important to establish a methodology to predict precisely afterbody drag so that accurate engine installed performance can be estimated. It was carried out in this paper to establish a methodology to predict afterbody drag of F-15K supersonic aircraft based on IMS(Integral Mean Slope) methodology, acquire afterbody drag data and compare its calculated data with the test data acquired from the wind tunnel test data based on 4.7% model scale. The comparison results showed good agreement between the calculated data and test data and it was found that the methodology described here to predict and test afterbody drag is acceptable.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.1
• /
• pp.98-103
• /
• 2017

In this paper, determination method for drag force and drag coefficient from results of firing test is described. The drag force and drag coefficient are determined through inverse operation of 2-dimensional projectile equation of motion. Determination method was verified by comparing analytical drag coefficient with data from flight test. Analysis of drag coefficient and drag reduction was performed with the data of flight test using artillery projectiles with base bleed unit.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.527-528
• /
• 2012

DBD (Dielectric Barrier Discharge) plasma actuator was designed for aerodynamic drag reduction using plasma flow control, and the drag reduction was measured by wind-tunnel tests using 2D test model. At the zero wind velocity, the plasma flow control had no effect on the drag reduction because the flow separation and surface friction drag were not occurred. At the wind velocity of 2m/s, 9.7% of drag was reduced by the flow separation control. The drag reduction decreased as the wind velocity increased.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.605-610
• /
• 2000

A series of wind tunnel test were conducted on Korean high speed train model to understand the flow physics around the vehicle related to the aerodynamic drag. For the wind tunnel test on high-speed ground vehicle, a moving ground simulation is necessary to predict the aerodynamic drag accurately. So, the models were tested in three wind tunnels with various ground simulation facility including moving belt ground plane system and tangential blowing system. The test results including measured aerodynamic drag and flow visualization showed that a tangential blowing method can be an alternative ground simulation method in short time using conventional wind tunnel.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.140-145
• /
• 2002

At present, wind tunnel test or CFD is used for predicting aerodynamic drag coefficient in motor company. But, wind tunnel test requires much cost and time, and CFD has about 30% error. In this study a predicting program of the aerodynamic drag coefficient based on empirical techniques was developed. Also a mathematical optimization method using GRG method was added to the program. The program was applied to six cars. Aerodynamic drag coefficient values of six cars were Predicted with 4.857% average error. The optimization method was also applied to six cars. Three parameters selected from sensitivity analysis were determined to reduce the afterbody drag coefficient to the value established by a designer and when some parameters were changed for a developing automotive, optimal modifiable parameters were determined to preserve the same drag coefficient as the original automotive. It was verified that this program could predict the aerodynamic drag coefficient effectively and accurately, and this program with GRG method could determine optimal values of parameters.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.5
• /
• pp.223-227
• /
• 2002

Wind tunnel test or CFD is used for predicting aerodynamic drag coefficient in domestic motor companies. But, wind tunnel test requires much cost and time, and CFD has a relatively large error. In this study a predicting program of the aerodynamic drag coefficient based on empirical techniques was developed. Also GRG method was added to the program in order to decide optimal values of some parameters. The program was applied to 24 cars and the aerodynamic drag coefficients were predicted with 4.82% average error. Optimization was also accomplished to 6 cars. Some parameters to be modified were determined (1) to reduce the afterbody drag coefficient to the value established by a designer and (2) to preserve the same drag coefficient as the original automotive when some parameters have to be changed in the viewpoint of design. It was verified that the developed program can predict the aerodynamic drag coefficient appropriately and determine optimal values of some parameters.

• International Journal of Aeronautical and Space Sciences
• /
• v.16 no.2
• /
• pp.311-324
• /
• 2015

This study presents computational analyses for low-drag aerodynamic design that are applied to modify a long-endurance UAV. EAV-2 is a test-bed for a hybrid electric power system (fuel cell and solar cell) that was developed by the Korean Aerospace Research Institute (KARI) for use in future long-endurance UAVs. The computational investigation focuses on designing a wing with a reduced drag since this is the main contributor of the aerodynamic drag. The airfoil and wing aspect ratio of the least drag are defined, the fuselage configuration is modified, and raked wingtips are implemented to further reduce the profile and induced drag of EAV-2. The results indicate that the total drag was reduced by 54% relative to EAV-1, which was a small-sized version that was previously developed. In addition, static stabilities can be achieved in the longitudinal and lateral-directional by this low-drag configuration. A long-endurance flight test of 22 hours proves that the low-drag design for EAV-2 is effective and that the average power consumption is lower than the objective cruise powerof 200 Watts.

• Journal of Mechanical Science and Technology
• /
• v.14 no.11
• /
• pp.1267-1275
• /
• 2000

A series do wind tunnel tests were conducted for Korean high-speed train model with various shape components to assess the contributions to aerodynamic drag. In order to elucidate the ground effects, two different wind tunnels, one with a moving ground system and the other with a fixed ground, were used for the same model and the results of both were compared and analyzed in detail. The result show that a suitable ground simulation is necessary for the test of a train model with many cars and detailed underbody. But the relative difference of the drag coefficients for the modifications of shape components can be measured by a fixed ground test with high accuracy and low cost. The effects of the nose shape, the inter-cargap and the bogie-fairing on total drag were discussed and some ideas were prosed to decrease the aerodynamic resistance of high speed train.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.14 no.3
• /
• pp.277-292
• /
• 2012

This paper presents the fundamental study on drag force of shield TBM cutter bit by scaled model test. Several theoretical analyses of the drag force of cutter bit have been studied. However, there are still some difference between the theoretical approaches and actual drag bit capacity. In order to study the drag forces of shield TBM cutter bit, the scaled model tests are carried out and analyzed. The results obtained from scaled model tests are compared with the existing theoretical equations. It is highly expected that the results of this study will be very essentially useful to design and develope the TBM cutterhead.