• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.513-516
• /
• 2008

The luminance efficiency of the red organic light-emitting devices fabricated utilizing a double electron transport layer (ETL) consisting of an Al-doped and an undoped layer was investigated. The Al atoms existing in the ETL acted as hole blocking sites, resulting in an increase in the luminance efficiency.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.734-736
• /
• 2008

A method to make the near and far images for a double layer 3D display system to create continuous depth illusion has been studied. The luminance ratio between the near and far images should be allocated based on the tone reproduction characteristics of the display systems.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.270-271
• /
• 2008

The contact resistance between organic semiconductor and source-drain electrode in Bottom Contact Organic Thin-Film Transistors (BCOTFTs) can be effectively reduced by metal oxide/molybdenum double layer structure; metal oxide layers including nickel oxide (NiOx/Mo) and moly oxide(MoOx) under molybdenum work as a high performance carrier injection layer. Step profiles of source-drain electrode can be easily achieved by simultaneous etching of the double layers using the difference etching rate between metal oxides and metal layers.

• Korean Journal of Optics and Photonics
• /
• v.18 no.6
• /
• pp.421-425
• /
• 2007

A new 3D rear projection display system using double-layer polarization-selective screen systems, one stacked in front of the other, has been developed. The front and rear screens are made of scattering polarizer films, and they either diffuse-scatter or transmit the incident light depending on the polarization state of the light. The near and for images are projected onto the front and rear screens, respectively, using light waves with mutually orthogonal polarization states. The new display system produces clear high-resolution images, which are visible over a wide range of viewing angle. It was found that the impression of depth is pronounced and eyestrain is only comparable to that by 2D display systems.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1071-1074
• /
• 2006

Ca/Ag double layer which is fabricated by thermal evaporation exists as the double layer of (Ca+O)/(Ag+Ca). In Ca layer, are crystalline Ca(OH)2 and amorphous Ca and in Ag layer, are crystalline Ag and amorphous Ca. And for the certain thickness of Ag, in the Ca/Ag double layer, the thicker Ca is, the higher transmittance is.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.30-33
• /
• 2008

Using a $Ir(ppy)_3$ doped in hole and electron transport host materials, simple three layers green PHOLEDs comprising double emissive layers have been fabricated. A low driving voltage value of 3.3 V to reach a luminance of $1000\;cd/m^2$ and maximum current- and power-efficiency values of 53.9 cd/A and 57.8 lm/W are demonstrated in this simple structure phosphorescent OLED.

• Journal of the Semiconductor & Display Technology
• /
• v.23 no.2
• /
• pp.65-70
• /
• 2024

Using a computational fluid dynamics(CFD) simulation tool, we have provided a coating guideline for slot-die coating with a double layer slot die head. We have analyzed the fluid dynamics in terms of the coating speed, flow rate ratio, and viscosity ratio, which are critical for the stability of coating meniscus. We have identified the common coating defects such as break-up, air entrainment, and leakage by varying the coating speeds. The flow rate ratio is the critical parameter determining the wet film thickness of the top and bottom layers. It is shown that when the flow rate ratio exceeds or equals 1.8, air entrainment occurs due to insufficient hydraulic pressure in the bottom layer, even though the total flow rate remains constant. Furthermore, we have found that the flow of the bottom layer is significantly affected by the viscosity of top layer. The viscosity ratio of 4 or higher obstructs the flow of the bottom layer due to the increased hydraulic resistance, resulting in leakage. Finally, we have demonstrated that as the viscosity ratio increases from 0.1 to 10, the maximum coating speed rises from 0.4 mm/s to 1.6 mm/s, and the minimum wet film thickness decreases from 800 ㎛ to 200 ㎛.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.677-680
• /
• 2009

DC influence between pixel electrode and alignment layer (AL) in in-plane switching mode LCD was analyzed through DC equivalence-circuit equation induction, DC charge-discharge simulation, luminance and residual-DC measurement systems using test patterned (TP) cell. DC discharging rate (DDR) of single layer electrode was faster than that of double layer electrode and DDR of low resistance AL was faster than that of high resistance AL. DC discharging characteristics had a close relation to layer number and resistance between two electrodes.

• Journal of the Semiconductor & Display Technology
• /
• v.17 no.4
• /
• pp.80-85
• /
• 2018

The present investigation on optical fiber mass manufacturing features the computational modeling and simulation on a double layer liquid coating process on glass fiber surface. The computational model employs a simplified geometry of typical fiber coating system which consists of primary and secondary coating dies along with secondary coating cup. The viscous dissipation in coating flow is incorporated into the double layer coating process simulations. Heavy temperature dependence of coating liquid viscosity is also considered in the model. The computational results found that the effects of viscous dissipation on both primary and secondary coating layer thicknesses are highly significant at higher drawing speed. Several important coating process parameters such as supply temperature and pressure of primary and secondary coating liquids are investigated and discussed in order to appreciate how those parameters affect the double layer coating layer thickness on fast moving glass fiber.

• Journal of Information Display
• /
• v.2 no.4
• /
• pp.8-14
• /
• 2001

Three types of conjugated polymers, poly(PZ-Pi), poly(PZ-BPI) and poly(PZ-NPI) were synthesized by Schiff-base reaction. These new conjugated polymers exhibited improved solubility in common organic solvents due to the presence of alkyl side chains as well as azomethine groups, Double layer LEDs made with the synthesized polymers as emitting layer and $Alq_3$, as electron transporting layer exhibited enhanced EL emission and efficiency compared to those of single layer LEDs. Double layer LEDs exhibited gradual shift in the emission peak th the single layer LED, made of only $Alq_3$ as the emitting layer as the thickness of $Alq_3$ layer increased.