• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.2
• /
• pp.431-434
• /
• 2011

In this paper, bandwidth enhanced design of dielectric resonator antenna fabricated in multi-layer substrate is introduced. The proposed dielectric resonator antenna is operating with fundamental TE101 mode and higher-order TM111 mode. Each resonance frequency is dependent on resonator dimensions. As increasing the height of radiating aperture, the higher-order TM111 mode resonance frequency approach the fundamental TE101 mode resonance frequency and the antenna bandwidth increase by double resonance. Three different aperture height size antennas that operated at 7GHz are fabricated in FR4 multi-layer substrate. Measured 10 dB matching bandwidth is 8 percent for single resonace antenna and 18 percent for double resonance antenna.

• Corrosion Science and Technology
• /
• v.20 no.5
• /
• pp.231-241
• /
• 2021

The objective of this study was to evaluate total current under steady-state conditions for a material undergoing corrosion using the electrochemical frequency modulation (EFM) technique, taking into account the presence of solution resistance and double layer capacitance. The analysis involving linearization of the Tafel curve allowed for the estimation of corrosion parameters. Results showed that the output signal was dependent on fundamental frequencies and their multiples. In addition, the output signal almost manifested itself at frequencies that were sums of fundamental frequencies of the applied sinusoidal signal. The harmonics calculated showed a significant shift from the principal frequency of input signals. The investigation involved the influence of corrosion current and anode-to-cathode Tafel slope ratio on faradaic and non-faradaic currents (including the average and RMS). The model presented showed both qualitative and quantitative improvements over the previously developed EFM technique that ignored the influence of solution resistance and the double layer capacitance while assuming the applied DC potential corresponded to the corrosion potential of the corroding material.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.3
• /
• pp.276-282
• /
• 2014

In a single-phase grid-connected power system consisting of a dc-dc converter and a dc-ac converter, the current drawn from renewable energy sources has a tendency to be pulsated and contains double-fundamental frequency ripple components, which results in several drawback such as a power harvesting loss and a shortening of the energy source's life. This paper presents a new double-fundamental current reduction-scheme with a fast dc-link voltage loop for two-stage dc-dc-ac grid connected systems. In the frequency domain, an adequate control design is performed based on the small-signal transfer function of a two-stage dc-dc-ac converter. To verify the effectiveness of proposed control algorithm, a 1 kW hardware prototype has been built and experimental results are presented.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.8
• /
• pp.1023-1032
• /
• 2003

The effect of local forcing on the separated flow over a backward-facing step is investigated through hot-wire measurements and flow visualization with multi-smoke wires. The boundary layer upstream of the separation point is laminar and the Reynolds number based on the free stream velocity and the step height is 13800. The local forcing is given from a slit located at the step edge and the forcing signal is always defined when the wind tunnel is in operation. In case of single frequency forcing, the streamwise velocity and the reattachment length are measured under forcing with various forcing frequencies. For the range of 0.010〈S $t_{\theta}$〈0.013, the forcing frequency component of the streamwise velocity fluctuation grows exponentially and is saturated at x/h = 0.75 , while its subharmonic component grows following the fundamental and is saturated at x/h = 2.0. However, the saturated value of the subharmonic is much lower than that of the fundamental. It is observed that the vortex formation is inhibited by the forcing at S $t_{\theta}$ = 0.019 . For double frequency forcing, natural instability frequency is adopted as a fundamental frequency and its subharmonic is superposed on it. The fundamental frequency component of the streamwise velocity grows exponentially and is saturated at 0.5 < x/ｈ < 0.75, while its subharmonic component grows following the fundamental and is saturated at x/ｈ= 1.5 . Furthermore, the saturated value of the subharmonic component is much higher than that for the single frequency forcing and is nearly the same or higher than that of the fundamental. It is observed that the subharmonic component does not grow for the narrow range of the initial phase difference. This means that there is a range of the initial phase difference where the vortex parring cannot be enhanced or amplified by double frequency forcing. In addition, this effect of the initial phase difference on the development of the shear layer and the distribution of the reattachment length shows a similar trend. From these observations, it can be inferred that the development of the shear layer and the reattachment length are closely related to the vortex paring.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.1
• /
• pp.169-174
• /
• 2011

For a double-walled carbon nanotube resonator with a short outer nanotube, the free edge of the short outer wall plays an important role in the vibration of the long inner nanotube. For a double-walled carbon nanotube resonator with a short inner nanotube, the short inner nanotube can be considered as a flexible core, thus, the fundamental frequency is influenced by its length. In this paper, we analysis frequency variation in ultrahigh frequency nanomechanical resonators based on double-walled carbon nanotubes with different wall length. This results will widely apply to the realization of frequency devices controlling the length of the inner or outer nanotube.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.8 s.111
• /
• pp.719-724
• /
• 2006

In this paper, we designed the double conversion down mixer by using Half-LO frequency in 2.3 GHz band. The IF frequency is obtained by supplying two LO frequencies to HEMT in both gate type and resistive type. The proposed mixer uses Half-LO frequency the same way as conventional sub-harmonic mixers. However the proposed one uses fundamental component of Half-LO frequency in first stage instead of using second harmonic components of Half-LO frequency, and the IF frequency is obtained by resistive type mixer in second stage, thereby the proposed mixer can improve linearity in comparison with conventional active mixer. We can verify that the proposed mixer has an conversion loss of 5dBm and IIP3 of 16.25dBm by using 10 dBm Power.

• Steel and Composite Structures
• /
• v.44 no.2
• /
• pp.155-169
• /
• 2022

In the present paper an analytical model was developed to study the non-linear vibrations of Functionally Graded Carbon Nanotube (FG-CNT) reinforced doubly-curved shallow shells using the Multiple Scales Method (MSM). The nonlinear partial differential equations of motion are based on the FGM shallow shell hypothesis, the non-linear geometric Von-Karman relationships, and the Galerkin method to reduce the partial differential equations associated with simply supported boundary conditions. The novelty of the present model is the simultaneous prediction of the natural frequencies and their mode shapes versus different curvatures (cylindrical, spherical, conical, and plate) and the different types of FG-CNTs. In addition to combining the vibration analysis with optimization algorithms based on the genetic algorithm, a design optimization methode was developed to maximize the natural frequencies. By considering the expression of the non-dimensional frequency as an objective optimization function, a genetic algorithm program was developed by valuing the mechanical properties, the geometric properties and the FG-CNT configuration of shallow double curvature shells. The results obtained show that the curvature, the volume fraction and the types of NTC distribution have considerable effects on the variation of the Dimensionless Fundamental Linear Frequency (DFLF). The frequency response of the shallow shells of the FG-CNTRC showed two types of nonlinear hardening and softening which are strongly influenced by the change in the fundamental vibration mode. In GA optimization, the mechanical properties and geometric properties in the transverse direction, the volume fraction, and types of distribution of CNTs have a considerable effect on the fundamental frequencies of shallow double-curvature shells. Where the difference between optimized and not optimized DFLF can reach 13.26%.

• Journal of electromagnetic engineering and science
• /
• v.10 no.1
• /
• pp.1-5
• /
• 2010

A spurious suppressed bandpass filter is proposed and discussed using the stepped impedance resonator(SIR) on a substrate-integrated waveguide(SIW) structure with a double-layer substrate. The second resonance of the fundamental $TE_{10}$ mode can be controlled by adjusting the electrical length and impedance ratio of each SIR. The spurious suppressed SIW bandpass filter shows the measurement results of the insertion loss of 3.98 dB and return loss of less than 11.58 dB at the center frequency of 12 GHz. Also, the second spurious frequency is improved to about $1.5f_0$ compared with $1.33f_0$.

• Advances in nano research
• /
• v.6 no.2
• /
• pp.135-145
• /
• 2018

This work represents the study of the vibration response of the double walled carbon nanotubes (DWCNT) for various boundary conditions. The inner and outer carbon nanotubes are modeled as two individual Euler-Bernoulli's elastic beams interacting each other by Van der waals force. Differential transform method (DTM) is used as a numerical method to solve the governing differential equations and associated boundary conditions. The influence of Winkler elastic medium on vibration frequency is also examined and results are interpreted. MATLAB is used as a tool for solving the governing differential equations. The fundamental natural frequencies are validating with those available in literature and observed a good agreement between them.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.50 no.3
• /
• pp.101-108
• /
• 2001

Frequency is an important operating parameter of a power system. Electric power systems sustain transient frequency swings whenever the balance between generation and load does not no longer hold. To cope with this constraints, it requires an accurate and high speedy frequency deviation estimation technique and suitable adjustment to obtain the Power system energy balance. This paper describes a digital signal processing technique for measuring the operating frequency of a power system. The fundamental frequency component of 3-phase signal is first extracted by using an algorithm based on FIR filter. The rate change of the phase angle is used for estimation. To confirm the validity of the proposed algorithm, the simulation studies carried out on a typical 154KV double T/L system by using EMTP software. Some test results are presented in the paper.