• 한국농공학회지
• /
• 제41권3호
• /
• pp.91-100
• /
• 1999

Tow constitutive models for weathered granite soil, Yasufuku's constitutive model with a single yield surface and Lade's constitutive model with two intersectiong yield surface compared in terms of their capabilities to accurately capture the observed behavior of compacted weathered grainite soil for various stress-paths. Both the single surface and the double surface models capture the experimentally observed behavior at a variety of stress-paths with good accuracy. The double surface model may model the observed compacted weathered granite soil behavior with better accuracy for proportational loading with increasing stress, but the single surface model may model dilatancy property with better accuracy for p-constant loading with increasing stress ratio.

• 한국농공학회지
• /
• 제40권1호
• /
• pp.106-117
• /
• 1998

The nature of stress-path dependency, the principle that governs deformations in granular soil, and the use of Lade's double work-hardening model for predicting soil response for a variety of stress-paths have been investigated, and are examined The test results and the analyses presented show that under some conditions granular soils exhibit stress-path dependent behavior. For stress-paths involving unloading or reloading, the stress-path with the higher average stress level produces the larger strains, whereas all stress-paths having the same intial states of stress, and involving only primary loading conditions, produce strains of similar magnitudes. Experimental evidence indicates that the stress- path dependent response obtained from the double work-hardening model is also observed for real soils. It is concluded that the influence of stress history on the friction angle is negligible and the strains increment direction is uniquely determined from the state of stress but is not perpendicular to the yield surface. The strains calculated from Lade's double work-hardening model are in reasonable agreement with those measured.

• 한국농공학회지
• /
• 제35권4호
• /
• pp.106-118
• /
• 1993

The purpose of this study is to develop a multireservoir water balance model which may be used to evaluate rural water demands such as agricultural water, domestic water, industrial water and livestock water and to determine effective storage of reservoir. The model was verified to compare the observed reservoir release data with the simulated reservoir release data of the existing Munsan and Dongbu reservoirs located in the Gisan rural district for 3 years('87~'89). For model application, the effective storages of existing reservoirs(Munsan & Dongbu) were evaluated for 10-year frequency drought and that of newly planned reservoirs(Kumbok & Kudong) were determined for 10-year frequency drought. In addition, the behavior of effective storages for existing reservoirs were analyzed in the case of introducing new reservoirs in the existing system.

• 동력기계공학회지
• /
• 제11권3호
• /
• pp.22-28
• /
• 2007

Liquefied gas vaporizer is a machine to vaporize liquefied gas such as liquid nitrogen($LN_{2}$), liquefied natural gas(LNG), liquid oxygen($LO_{2}$) etc. For the air type vaporizer, the frozen dew is created by temperature drop (below 273 K) on vaporizer surface. The layer of ice make a contractions on vaporizer. The structure analysis on the heat transfer was studied to see the effect of geometric parameters of the vaporizer, which are length 1000 mm of various type vaporizer. Structure analysis result such as temperature variation, thermal stress and thermal strain have high efficiency of heat emission as increase of thermal conductivity. As the result, Frist, With-fin model shows high temperature distribution better than without-fin on the temperature analysis. Second, Without-fin model shows double contractions better then with-fin model under the super low temperature load on the thermal strain analysis. Third, Vaporizer fin can be apply not only heat exchange but also a stiffener of structure. Finally, we confirm that All model vaporizer can be stand for sudden load change because of compressive yield stress shows within 280 MPa on thermal stress analysis.

• Tribology and Lubricants
• /
• 제13권3호
• /
• pp.115-123
• /
• 1997

The electrorheological (ER) behavior of suspensions in silicone oil of silica gel powder (average particle size 49 $\mu$m) absorbed water was investigated at room temperature with electric fields up to 2.4 KV/mm. In this paper, for development of succcessful ER fluids used for wide temperature range later, we would like to know a fundamental understanding of water on ER effect. As a first step, the ER fluids involving water activated silica gel were measured not only the electrical characteristics such as dielectric constant, current density and electrical conductivity but also the rheological properties on the strength of electric field, the quantity of dispersed phase and absorbed water. From the experimental results that water absorbed to the particles directly affects to the surface charge density of electric double layer model proposed by Schwarz and makes dielectric constant and current density of ER fluids increase. The current density and dynamic yield stress $($\tau$_y)$ of water activated silica gel suspensions was in exponential proportion to the strength of electric field, the quantity of dispersed phase and absorbed water. And the optimum water quantity and weight concentration of silica gel for electrorheological effect were 4-5 wt% and 15 wt%, respectively.

• 한국구조물진단유지관리공학회 논문집
• /
• 제26권6호
• /
• pp.39-46
• /
• 2022

철근콘크리트 구조물의 설계 방법으로 한계상태설계법이 적용되면서 해석이나 설계 시 극한상태까지 고려하도록 하고 있다. 실제로 철근콘크리트 부재가 휨을 받을 때 전단철근에 의한 구속 효과가 존재하지만, 설계 시에는 비구속 콘크리트의 재료 곡선을 적용하도록 하고 있다. 본 연구에서는 휨 부재에 대한 구속콘크리트 모델의 적합성을 평가하기 위하여 복철근 직사각형 단면을 가지는 RC 단순보에 대하여 4점 휨 실험을 수행하였고, 영상분석기법을 이용하여 부재의 항복 후 거동을 상세하게 분석하였다. 상세한 분석을 위하여 DIC 기법을 영상분석 기법으로써 채택하였고, 기존 계측 방법과 계측 결과를 비교함으로써 DIC 기법의 타당성을 검증하였다. DIC 기법의 결과로 산출된 콘크리트 표면의 변형률 분포도를 얻을 수 있었고, 이를 통하여 단면의 평균 변형률 분포를 산출하였다. 평균 변형률 분포도를 이용하여 기존 구속콘크리트 모델을 재료곡선으로 적용한 응력 분포도를 도출할 수 있었다. 실험 결과와 기존 모델 적용 결과의 비교를 통하여 직사각형 단면을 가지는 RC 휨 부재에 대한 구속콘크리트 모델의 적합성을 평가하였다.

• KSBB Journal
• /
• 제21권4호
• /
• pp.279-285
• /
• 2006

본 연구에서는 trypsin을 모델 단백질로 하여 단백질 본연의 환성을 유지할 수 있는 고정화 방법을 찾기 위하여 공유결합방법과 친화력 결합방법을 이용하여 trypsin을 고정화 하였다. Streptavidin-biotin system을 이용한 고정화 방법은 bioactivity 유지측면에서 공유결합 방법보다 우수함을 확인하였다. 하지만 streptavidin-biotin system을 이용하였을 때 고정화 수율이 낮은 것은 해결해야 할 과제이다. 분자량이 다른 기질들(BAPNA, insulin, BSA)을 대상으로 고정화 trypsin의 부위 특이적 절단 특성을 분석한 결과 streptavidin-biotin에 의해 고정화된 trypsin이 절단효율도 높고 sequence coverage도 높은 것으로 확인되었다. 또한 공유결합된 trypsin은 견고한 분자구조를 나타낸 반면 streptavidin-biotin system으로 고정화된 trypsin은 유연성이 높은 것을 QCM-D를 이용하여 관찰할 수 있었다. 따라서 streptavidin-biotin system에 의한 고정화 방법에서 streptavidin-biotin 결합이 일종의 spacer arm 역할을 하면서 고정화된 trypsin의 분자유연성을 향상시켜 절단반응의 부위특이성과 절단수율을 향상시키는 것으로 판단되었다.