• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.11a
• /
• pp.153-154
• /
• 2022

When reinforcing an existing building with the Concrete Filled Tube(CFT) structure, it is impossible to form a diaphragm inside with the existing method. Therefore, in this study, a construction method was proposed so that the force could be transmitted using the friction force between the diaphragm and the concrete using a double diaphragm.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.3
• /
• pp.18-24
• /
• 2011

This paper presents that the yield strength of the pressure sensor with a double boss diaphragm structure can be improved as the grooves are formed at the corner of the diaphragm bridge. Generally the boss structure is widely used for the low-pressure sensor, of which the sensitivity is not enough in case of the small diaphragm size limited by a chip size constraint. The double boss structure pressure sensor exhibits a great sensitivity, but suffers from the low yield strength problem due to the high stress occurred at the corner of the diaphragm bridge to be limited in the operating range. ANSYS simulation is performed by changing the length of the groove from 0.5${\mu}m$ to 10${\mu}m$ at the corner of the diaphragm bridge of the double boss structure pressure sensor. The maximum stress is analyzed at the corner of the diaphragm bridge, the edge of the diaphragm bridge, and the position of the piezoresistive sensor. Consequently, in case the length of the groove from the edge of the diaphragm is 6${\mu}m$ or greater, the stress occurred in the corner of the bridge is less than the stress acting on a piezoresistive element.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1996.10a
• /
• pp.195-201
• /
• 1996

The dynamic characteristics of externally pressurized journal bearing have been studied theoretically. The Reynolds' equation has been solved by FDM, and the dynamic coefficients have been calculated by using perturbation method. The bearing is compensated by orifice or double-pad diaphragm control valve. The effects of diaphragm initial gap and stiffness are considered. As the results of analysis, it is shown that a control valve has better performance than orifice.

• Journal of Sensor Science and Technology
• /
• v.30 no.5
• /
• pp.273-278
• /
• 2021

Here, we studied the change in the mechanical stiffness of a diaphragm according to the corrugation pattern. The diaphragm consists of a silicon oxide and nitride double layer; a corrugation pattern was formed by dry etching, and the diaphragm was released by wet etching. The fabrication of the thin film was verified using focused ion beam and scanning electron microscopy images. The mechanical stiffness of the diaphragm was obtained by measuring the surface vibration using a laser Doppler vibrometer while applying external sound pressure. Flat squares, diaphragms with square corrugations, and circular corrugation patterns were measured and compared. The stiffness of the diaphragm with a corrugation structure was found to be smaller than that without a corrugation structure; in particular, circular corrugation showed a better effect because of the high symmetry. Furthermore, the effect of corrugation was theoretically predicted. The proposed corrugated diaphragm showed comparable flexibility with the state-of-the-art MEMS microphone diaphragm.

• Journal of Korean Ophthalmic Optics Society
• /
• v.6 no.1
• /
• pp.13-29
• /
• 2001

A mathematical model was proposed to analyze the vibration of diaphragm, such as the contact lenses fitted on the eyes, being subjected to the external sinusoidal pressure. The model incorporates the differential equations and their numerical solution program, based on the wave equations. Turbo-C and graphic software, formulated to describe the dependence of the various parameters involved in the vibration. The model predicts the radial distribution of amplitude, frequency dependence of both average displacement amplitude and the power of diaphragm whose edge is being either simply supported or rigidly clamped in vibration. The effect of variables such as thickness, radius, damping coefficients on the vibration characteristics was illustrated by the computer simulation of the derived program. As the frequency of driving pressure increases above the certain value determined by the boundary conditions and parameters the wave shape or pattern changes from simple arc to belly or loops having double antinode. It seems that the effect of outer antinode progressively increases as the frequency increases. If this kind of phenomena occurs to the contact lens on the cornea in vivo, it may cause an abnormal correction power in the lenses or pull off the eye due the increased rise of outer part of the lens.

• Steel and Composite Structures
• /
• v.41 no.5
• /
• pp.747-759
• /
• 2021

Built-up Double-I (BD-I) columns have been commonly used for mid-rise steel-frame structures in Iran. These columns consist of two hot rolled IPE sections which are connected by two cover plates and fillet welds. Until 2017, BD-I columns were employed in intermediate moment resisting frames (MRF) using welded flange plate (WFP) connections. To evaluate the seismic behavior of the connections, four samples were made and tested based on cyclic loading according to AISC 341-16. It was concluded that typical samples cannot satisfy the seismic provisions related to intermediate MRFs. In contrast, the proposed connections retrofitted with two-part external diaphragms were able to satisfy not only the seismic requirements related to intermediate MRFs but also those related to special MRFs according to AISC. The numerical modeling of these samples was performed using ABAQUS finite element software. This study compared the hysteresis moment-rotation curves, plastic strains, and behavior modes in both experimental samples and numerical models.

• Transactions of Materials Processing
• /
• v.23 no.1
• /
• pp.10-15
• /
• 2014

Recently, micro-speakers have attracted much attention due to their increasing demand in mobile devices. Micro-speakers use polymer diaphragms, which are manufactured from thin polymer film by the thermoforming process. The diaphragm is generally designed to be a circular membrane with a cross section consisting of a double dome structure, and a number of corrugations are located in the outer region to produce better sound quality. In the current study, a finite element (FE) analysis is performed for thermoforming, and the resulting thickness reduction in the corrugation regions is estimated. The estimated thickness distribution is used in further structural and modal FE analyses, from which the effects of local thickness reduction on the stiffness and vibration characteristics are determined.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.8
• /
• pp.790-796
• /
• 2013

Micro-speaker diaphragms play an important role in generating a desired audio response. The diaphragm is generally a circular membrane, and the cross section is a double dome, with an inner dome and an outer dome. To improve the sound quality of the speaker, a number of corrugations may be included in the outer dome region. In this study, the role of these corrugations is investigated using two kinds of finite element method (FEM) calculations. Structural FEM modeling was carried out to investigate the change in stiffness of the diaphragm when the corrugations were included. Modal FEM modeling was then carried out to compare the natural frequencies and the resulting vibrational modes of the plain and corrugated diaphragms. The effects of the corrugations on the vibration characteristics of the diaphragm are discussed.

• Explosives and Blasting
• /
• v.20 no.3
• /
• pp.59-71
• /
• 2002

The points of this design case are the planning and excavation method of a new double-tracked railroad tunnel which is approx. 11∼22 meters apart from existing single-tracked railroad tunnel. For the optimum excavation method some needs are required in design stage, such as the reduction of noise and vibration, public resentment, damage of buildings and construction costs. Hence the estimation and application of allowable noise and vibration criterion is important. The ground coefficient (K, n) of this site is determined by field trial blasting. The excavation method is chosen to satisfy the allowable noise and vibration criterion. In addition, in order to ensure the stability of existing single-tracked railroad tunnel, the instrumentation of maintenance level is accompanied during the construction stage. As a result of this design condition, central diaphragm excavation with line drilling and pre-large hole boring blasting is applied to the area within 15 meters apart from existing tunnel. And above 15 meters apart, pre-large hole boring blasting is designed.

• 한국가시화정보학회:학술대회논문집
• /
• 2007.11a
• /
• pp.59-62
• /
• 2007

The basic concept and preliminary performance results of a miniaturized electroosmotic (EO) pump with diaphragms were included in the present study. The separation of an electroosmotic pumping liquid from a drug using diaphragms is mainly to have a freedom in choosing an electroosmotic pumping liquid and to achieve the optimal drug delivery, and, preferably its precise control. We performed maximum flow rate, maximum pressure, and maximum current measurements with and without diaphragm designs. As a result, the effect of diaphragms on pump performance at the maximum condition is small. However, the presence of diaphragms does not allow indefinite continuous pumping.