• Journal of Ocean Engineering and Technology
• /
• v.24 no.6
• /
• pp.71-75
• /
• 2010

Although Graphite Compacted Vermicular (GCV) was first observed in 1948, the narrow range for stable foundry production precluded the high volume application of GCV to complex components such as cylinder blocks and heads until advanced process control technologies became available. This, in turn, had to await the advent of modern measurement electronics and computer processors. Following the development of foundry techniques and manufacturing solutions, primarily initiated in Europe during the 1990s, the first series production of GCV cylinder blocks began during 1999. Today, more than 40,000 GCV cylinder blocks are produced each month for OEMs, including Audi, DAF, Ford, Hundai, MAN, Mercedes, PSA, Volkswagen, and Volvo. Given that new engine programs are typically intended to support three to four vehicle generations, the chosen engine materials must satisfy current design criteria and also provide the potential for future performance upgrades without changing the overall block architecture. With at least a 75% increase in the ultimate tensile strength, a 40% increase in the elastic modulus, and approximately double the fatigue strength of either iron or aluminum, GCV is ideally suited to meet current and future of engine design and performance requirements.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.162-162
• /
• 2014

최근 들어 wearable computing에 대한 수요가 증가하면서 flexible device에 대한 연구가 활발히 진행되고 있다. 하지만, flexible device를 구현하기 위해서는 기판의 damage를 줄이기 위한 저온공정, device life-time 향상을 위한 passivation, 와이어 본딩 등 다양한 문제들이 해결 되어야 한다. 이러한 문제들 중, polymer 기판과 금속간의 접착력을 향상시키기 위해서 많은 연구자들은 기판의 표면에 adhesive layer를 도포하거나 금속잉크의 solvent를 변화시키는 등의 연구를 진행해왔다. 종래의 연구는 기존 device를 대체 할 수 있을 정도의 생산성과 polymer 기판에 대한 열 적인 손상 이 문제가 되었다. 종래의 문제를 해결하기 위하여 저온공정, in-line system이 가능한 준 준 대기압 플라즈마를 사용하였다. 본 연구에서는 금속잉크를 Ink-jet으로 jetting하여 와이어 본딩 하는 과정에서 전도성 ink의 선폭을 유지시키고 접착력을 향상하기 위하여 준 대기압 플라즈마 공정을 이용하여 이러한 문제점을 해결하고자 하였다. Polymer 기판 표면에 roughness를 만들기 위해 대략 수백 nm 크기를 갖는 graphene flake를 spray coating하여 마스크로 사용하고 준 대기압 플라즈마를 이용하여 표면을 식각 함으로써 roughness를 형성시켰다. 준 대기압 플라즈마를 발생시키기 위해 double discharge system에서 6 slm/1.5 slm (He/O2) gas composition을 하부 전극에 흘려보내고 60 kHz, 5 kV 파워를 인가하였다. 동시에 상부 전극에는 30 kHz, 5 kV 파워를 인가하여 110초 동안 표면 식각 공정을 진행하였다. Graphene flake mask가 coating되어 있는 유연기판을 산소 플라즈마 처리 한 후 물에 3초 동안 세척하여 표면에 남아있는 graphene flake를 제거하고 6 slm/0.3 slm (He/SF6)의 유량으로 주파수와 파워 모두 동일 조건으로 110초 동안 표면 처리를 하였다. Figure 1은 표면 개질 과정과 graphene flake를 mask로 사용하여 얻은 roughness 결과를 SEM을 이용하여 관찰한 결과이다. 이와 같이 실험한 결과 ink와 기판간의 접촉면적을 늘려주고 접촉 각을 조절하여 Wenzel model 을 형성 할 수 있는 표면 roughness를 생성하였고 표면의 화학적 결합을 C-F group으로 치환하여 표면의 물과 접촉각 이 $47^{\circ}$에서 $130^{\circ}$로 증가하는 것을 확인하였다.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.5
• /
• pp.454-460
• /
• 2016

Double-layered Al-Mg films have been deposited by using an e-beam deposition method on a cold-rolled steel sheet(CR), which the structure of the film was Al/Mg/CR. The micro-structure, alloy phase, and corrosion resistance of the Al-Mg coated CR were investigated before and after heat treatment at $400^{\circ}C$ for 2, 3, and 10 min in a nitrogen atmosphere. Total thickness of Al-Mg films was fixed at $3{\mu}m$ and the thickness ratio of Al and Mg layers(Al:Mg) has been changed from 5:1 to 1:5. The cross-sectional morphology of the films, which had the thickness ratio of 2:1(Al:Mg), 1:1, and 1:2, was changed after heat treatment from columnar to featureless structure. The x-ray diffraction data for as-deposited films showed only pure Al and Mg peaks. Al-Mg alloy peaks such as $Al_3Mg_2$ and $Al_{12}Mg_{17}$ phase appeared after the heat treatment. The Al-Mg coating with the thickness ratio of 1:1(Al:Mg) showed the best corrosion resistance of up to 500 hours by salt spray test.

• Corrosion Science and Technology
• /
• v.14 no.5
• /
• pp.213-217
• /
• 2015

Recently, household electronic industries require environmentally-friendly and highly functional steels in order to enhance the quality of human life. Customers especially require both excellent corrosion and abrasion resistant anti-fingerprint steels for digital TV panels. Thus POSCO has developed new functional electro-galvanized steels, which have double coated layers with organic-inorganic composites on the zinc surface of the steel for usage as the bottom chassis panel of TVs. The inorganic solution for the bottom layer consists of inorganic phosphate, magnesium, and zirconium compounds with a small amount of epoxy binder, and affords both improved adhesion properties by chemical conversion reactions and corrosion resistance due to a self-healing effect. The composite solution for the top layer was prepared by fine dispersion of organic-inorganic ingredients that consist of a urethane modified polyacrylate polymer, hardener, silica sol and a titanium complex inhibitor in aqueous media. Both composite solutions were coated on the steel surface by using a roll coater and then cured through an induction furnace in the electro-galvanizing line. New anti-fingerprint steel was evaluated for quality performance through such procedures as the salt spray test for corrosion resistance, tribological test for abrasion resistance, and conductivity test for surface electric conductance regarding to both types of polymer resin and coating weight of composite solution. New composite coated anti-fingerprint steels afford both better corrosion resistance and abrasion properties compared to conventional anti-fingerprint steel that mainly consists of acrylate polymers. Detailed discussions of both composite solutions and experimental results suggest that urethane modifications of acrylate polymers of composite solutions play a key role in enhanced quality performances.

• Membrane Journal
• /
• v.29 no.2
• /
• pp.96-104
• /
• 2019

The purpose of this paper is whether or not the in-situ restoration of the reverse osmosis (RO) membranes which its membrane function is lost is possible. The damaged RO membranes are double coated through the salting-out method by the poly(styrene sulfonic acid) sodium salt as the cationic exchange polymer and the polyethyleneimine as the anionic exchange polymer and also conducted the opposite order of the coating materials. And according to the concentration, time and ionic strength, the flux and rejection are measured for the coated membranes. Then the best coating condition is to apply for the RO membrane module of the household water purifier to know the possibility of the in-situ restoration for the commercial module. When the condition of the PEI 30,000 ppm (IS = 0.1)/PSSA 20,000 ppm (IS = 0.7) is applied, the rejection was enhance from 69% for the damaged module to 86% (90% for the pristine module).

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.6
• /
• pp.409-415
• /
• 2016

In this study, we test the effects of the surface roughness on the hydro efficiency of double-suction centrifugal pumps ($Q=70.7m^3/min$, H = 87 m). The original surface of the impeller and inner casing were coated, resulting in surface-roughness reductions ranging from $100{\sim}110{\mu}m$ to $0{\sim}0.08{\mu}m$. We conducted experimental studies to measure the efficiency of the pumps and operating-pump electro energy variations with different surface roughness values. The experimental results showed that the efficiency of the pumps increased by about 0.8~1.79% and the electric energy of the operating pump was reduced by around 4.38 ~ 6.08%. These results indicate that the performance of the pumps depend largely on the surface roughness of the impeller and inner casing, and by reducing the surface roughness, we can improve the efficiency of the pump and reduce costs by reducing the electric energy consumption.

• Journal of the Korean Ceramic Society
• /
• v.32 no.5
• /
• pp.617-625
• /
• 1995

In order to reduce reflectance of soda-lime glass having average reflectance of 7.35% and refractive index of 1.53, single (SiO2), double (SiO2/20SiO2-80ZrO2), and triple (SiO2/ZrO2/75SiO2-25ZrO2) layers were designed and fabricated on the glass substrate by Sol-Gel method. Stble sols of SiO2-ZrO2 binary system for antireflective (AR) coatings were synthesized with tetraethyl orthosilicate (TEOS) and zirconium n-butoxide as precursors and ethylacetoacetate (EAcAc) as a chelating agent in an atmosphere environment. Films were deposited on soda-lime glass at the withdrawal rates of 3~11 cm/min using the prepared polymeric sols by dip-coating and they were heat-treated at 45$0^{\circ}C$ for 10 min to obtain homogeneous, amorphous and crack-free films. In case of SiO2-ZrO2 binary system, refractive index of film increased with an increase of ZrO2 mol%. Designed optical constant of films could be obtained through varying the withdrawal rate. In the visible region (380~780nm), reflectance was measured with UV/VIS/NIR Spectrophotometer. Average reflectances of the prepared single-layer [SiO2 (n=1.46, t=103nm)], double-layer [SiO2 (n=1.46, t=1-4nm)/20SiO2-80ZrO2 (n=1.81, t=82nm)], and triple-layer [SiO2 (n=1.46, t=104nm)/ZrO2 (n=1.90, t=80nm)/75SiO2-25ZrO2 (n=1.61, t=94 nm)] were 4.74%, 0.75% and 0.38%, respectively.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.13 no.1
• /
• pp.9-14
• /
• 1999

One of the IIDSt difficult problems in a tri-band fluorescent lamp manufacture is to search a desired color by an adequate mixing of tri-color phosphors. When a light spectrum of a phosphor is slightly changw or distorted due to process variable or when another spectrum such as from Ar, Kr or a iDosphor of calcium halo-phosphate as a first layer exist, it is even rrnre difficult to search a desired color. In this work, a rapid awuaching rrethod to a desired light color was studied. 1bree single-color fluorescent lamps and three-color-mixed fluorescent lamps with different mixing ratios were prepared and the spectra of these lamps were measured, from which the rrercury and the argon spectra were eliminatffl to obtain the rrndifiw color coordinates. From this rrndifiw color coordinate, h.lIlHl ratios of green and blue to red were correlatffl with their weight ratios. This correlation was awliw to the industrial line for single and double layer coating and proven to be valuable as a desired color matching procWure in tri-color fluorescent lamp manufacture.acture.

• Journal of the Korean Electrochemical Society
• /
• v.4 no.3
• /
• pp.113-117
• /
• 2001

Specific capacitance and charge-discharge rate of EDLC using activated carbon electrode were affected by the compositions of electrolytes, the conditions of charge-discharge and physical properties of activated carbon materials. The activated carbon electrode was prepared by dip coating method. Charge-discharge test and electrochemical experiments were carried out for various kinds of organic electrolytes. Effects of charge and discharge current density on the specific capacitance were studied. Characteristics of leakage current, self-discharge and time-voltage curves in optimum conditions of organic electrolytes were compared with conventional $1M-Et_4NBF_4/PC$ electrolyte. The EDLC using MSP-20(specific surface area: $2000m^2/g$) electrode and $1M-LiPF_6/PC-DEC(1:1)$ was exhibited th highest specific capacitance of 130F/g and low polarization resistances. The EDLC using MSP-20 electrode at $1M-LiPF_6/PC-DEC(1:1)$ was small leak current of 0.0004A for 15min, long voltage retention of 0.8V after 100h and linear time-voltage curves with small IR-drop.

• Journal of the Korean institute of surface engineering
• /
• v.33 no.2
• /
• pp.93-100
• /
• 2000

Effects of Ti content and Ti underlayer on the pitting behavior of TiN coated AISI 304 stainless steel have been studied. The stainless steel containing 0.1~1.0wt% Ti were melted with a vacuum melting furnace and heat treated at $1050^{\circ}C$ for 1hr for solutionization. The specimen were coated with l$\mu\textrm{m}$ and 2$\mu\textrm{m}$ thickness of Ti and TiN by E-beam PVD method. The microstructure and phase analysis were conducted by using XRD, XPS and SEM with these specimen. XRD patterns shows that in TiN single-layer only the TiN (111) Peak is major and the other peaks are very weak, but in Ti/TiN double-layer TiN (220) and TiN (200) peaks are developed. It is observed that the surface of coating is covered with titanium oxide (TiO$_2$) and titanium oxynitride ($TiO_2$N) as well as TiN. Corrosion potential on the anodic polarization curve measured in HCl solution increase in proportion to the Ti content of substrate and by a presence of the Ti underlayer, whereas corrosion and passivation current densities are not affected by either of them. The number and size of pits decrease with increasing Ti content and a presence of the coated Ti film as underlayer in the TiN coated stainless steel.