• Journal of Korea Water Resources Association
• /
• v.42 no.12
• /
• pp.1125-1133
• /
• 2009

Evanescent modes which are the other solutions of the Laplace equation for the linear dispersion equation may affect the wave transformation especially when a water depth varies abruptly. In this study, the effects of evanescent modes for a three-dimensional depression of seabed are investigated by using the eigenfunction expansion method. A convergence test is first carried out by changing numbers of domains and evanescent modes. The wave transformation for various depressions of seabed is then calculated under condition that the solution of the eigenfunction expansion method is converged.

• The Journal of Engineering Geology
• /
• v.24 no.2
• /
• pp.191-199
• /
• 2014

We describe a method for detecting slope instability in flume tests using pore pressure and water content data in conjunction with a statistical control chart analysis. Specifically, we conducted univariate statistical analysis on x-MR control chart data (pore pressure and water content) collected at several points along the flume slope, which we separated into three parts: upper, middle, and lower. To assess our results in the context of landslide forecasting and warning systems, we applied control limit lines at $1{\sigma}$, $2{\sigma}$, and $3{\sigma}$ levels of uncertainty. In doing so, we observed that dispersion time varies depending on the control limit line used. Moreover, the detection of instabilities is highly dependent on the position and type of sensor. Our findings indicate that different characteristics of the data on various factors predict slope failure differently and these characteristics can be identified by univariate statistical analysis. Therefore, we suggest that a univariate statistical approach is an effective method for the early detection of slope instability.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.9
• /
• pp.1267-1275
• /
• 2002

An experimental study was performed to investigate adiabatic wall temperature and heat transfer coefficient around a module cooled by forced air flow. The flow angle of attack to the module were 0$^{\circ}$and 45$^{\circ}$. In the first method, inlet air flow(1~7m/s) and input power.(3, 5, 7W) were varied after a heated module was placed on an adiabatic floor(320$\times$550$\times$1㎣). An adiabatic wall temperature was determinated to use liquid crystal film. In the second method to determinate heat transfer coefficient, inlet air flow(1~7m/s) and the heat flux of rubber heater(0.031~0.062W/$m^2$) were varied after an adiabatic module was placed on rubber heater covering up an adiabatic floor. Additional information is visualized by an oil-film method of the surface flow on the floor and the module. Plots of $T_{ad}$ and $h_{ad}$ show marked effects of flow development from the module and dispersion of thermal wake near the module. Certain key features of the data set obtained by this investigation may serve as a benchmark for thermal-design codes based on CFD.

• Carbon letters
• /
• v.24
• /
• pp.1-9
• /
• 2017

We studied the basic properties and fabrication of reduced graphene oxide (rGO) prepared using eco-friendly reduction agents in the graphene solution process. Hydrazine is generally used to reduce graphene oxide (GO), which results in polluting emissions as well as fixed nitrogen functional groups on different defects in the graphene sheets. To replace hydrazine, we developed eco-friendly reduction agents with similar or better reducing properties, and selected of them for further analysis. In this study, GO layers were produced from graphite flakes using a modified Hummer's method, and rGO layers were reduced using hydrazine hydrate, L-ascorbic acid, and gluconic acid. We measured the particle sizes and the dispersion stabilities in the rGO dispersed solvents for the three agents and analyzed the structural, electrical, and optical properties of the rGO films. The results showed that the degree of reduction was in the order L-ascorbic acid ${\geq}$ hydrazine > glucose. GO reduced using L-ascorbic acid had a sheet resistance of $121k{\Omega}/sq$, while that reduced using gluconic acid showed worse electrical properties than the other two reduction agents. Therefore, L-ascorbic acid is the most suitable eco-friendly reduction agent that can be substituted for hydrazine.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.6
• /
• pp.570-578
• /
• 2009

Excitation and propagation of guided waves are very complex problems in pipes due to their dispersive nature. Pipes are commonly used in the oil, chemical or nuclear industry and hence must be inspected regularly to ensure continued safe operation. The normal mode expansion(NME) method is given for the amplitude with which any propagating waveguide mode is generated in the pipes by applied surface tractions. Numerical results are calculated based on the NME method using different sources, i.e., non-axisymmetric partial loading and quasi-axisymmetric loading sources. The sum of amplitude coefficients for 0~nineth order of the harmonic modes are calculated based on the NME method and the dispersion curves in pipes. The superimposed total field which is namely the angular profile, varies with propagating distance and circumferential angle. This angular profile of guided waves provides information for setting the transducer position to find defects in pipes.

• Journal of Advanced Navigation Technology
• /
• v.6 no.3
• /
• pp.223-230
• /
• 2002

In this paper, we induced that the noise powers and bit error rate of direct detection receiver taking account of ISI (intersymbol interference) in the 2,000 km optical transmission system. And we evaluated the sensitivity in the vrious bit rate system. We verified that the proposed calculation method is applicable to the exact optical system. And we confirmed that the signal distortion due to both chromatic dispersion and nonlinear effects compensated by using of MSSI (Mid-Span Spectral Inversion) method, and yet the sensitivity of a higher bit rate system is reduced, because of the increase of ISI and then the decrease of the average receiving power, compared with a the lower bit rate system.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.09b
• /
• pp.842-845
• /
• 2005

A method for the numerical simulation of two-dimensional free-surface flow resulting from the propagation of regular gravity waves over topography with arbitrary bottom shape is presented. The method is based on the numerical solution of the Euler equations subject to the fully nonlinear free-surface boundary conditions and the appropriate bottom, inflow and outflow conditions using a hybrid finite-differences and spectral-method scheme. The formulation includes a boundary-fitted transformation, and is suitable for extension to incorporate large-eddy simulation (LES) and large-wave simulation (LWS) terms for turbulence and breaking wave modeling, respectively. Results are presented for the simulation of the free-surface flow over two different bottom topographies, with constant slope values of 1:10 and 1:20, two different inflow wave lengths and two different inflow wave heights. An absorption outflow zone is utilized and the results indicate minimum wave reflection from the outflow boundary. Over the bottom slope, lengths of waves in the linear regime are modified according to linear theory dispersion, while wave heights remain more or less unchanged. For waves in the nonlinear regime, wave lengths are becoming shorter, while the free surface elevation deviates from its initial sinusoidal shape.

• Journal of the Korean Electrochemical Society
• /
• v.15 no.4
• /
• pp.264-269
• /
• 2012

In this study, highly loaded(50 wt%) and very stable Pt/MWCNT catalysts for Polymer Electrolyte Membrane Fuel Cells(PEMFCs) are synthesized in short time scale by microwave assisted polyol method with different microwave irradiation time. The XRD and TEM results show that the Pt size becomes bigger as the microwave irradiation time increases. The mean Pt sizes of fabricated catalysts are 4.1, 4.9 and 8.5 nm when the microwave are irradiated for 10, 20 and 30 min, respectively. When compared with Pt catalyst made by conventional polyol method, it shows better long term durability due to the better Pt dispersion on the MWCNT surface.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.525-528
• /
• 2006

Transparent conducting films were fabricated on polyethylene terephthalate substrate by a spray method using double-walled carbon nanotubes dispersed in organic solvent and water-based solution. We analyzed the films by absorption spectra, sheet resistance, and scanning electron microscopy. Transparent conducting films with high uniformity and high transparency were fabricated by the spray method. We found that the dispersion particularly nanodispersion of CNTs was of crucial importance to improve the film performance.

• Journal of computational fluids engineering
• /
• v.2 no.1
• /
• pp.93-108
• /
• 1997

This paper describes several computational results on the various energy and environmental problems using Patankar's SIMPLE method. The specific problems included in this study are : pollutant and flammable material dispersions in open and confined areas, buoyancy-driven flow in a lake, primary clarifier for water and waste water treatment, hood ventilation in workplace. cyclone combustor and Dow chlorination reactor. A control-volume based finite-difference method is employed together with the power-law scheme. The pressure-velocity coupling is resolved by the use of the revised version of SIMPLE, says SIMPLER and SIMPLEC. The Reynolds stresses are closed using the standard or RNG κ-ε models. A nonequilibrium turbulent reaction model is developed for the application of the chlorination process in the Dow thermal reactor. Other important empirical models and physical insights appeared in this study are presented and discussed in a brief note. The computational method developed in this study is considered, in general, as a viable tool for the design and determination of the optimal operating condition of various environmental engineering system of interest.