• Elastomers and Composites
• /
• v.41 no.4
• /
• pp.252-259
• /
• 2006

A new route for making rubber/clay nanocomposites was suggested based on skim natural rubber latex (SNRL), which is a protein rich by-product obtained during the centrifugal concentration of natural rubber (NR) latex. NR/acrylonitrile butadiene rubber (NBR) based nanocomposites were prepared from SNRL and NBR latex of 26 % acrylonitrile content by blending of aqueous dispersion of organoclay (OC) followed by coagulation, drying, mill mixing and vulcanization. X-ray diffraction(XRD) studies revealed that NR/NBR blend nanocomposites exhibited a highly intercalated and exfoliated structure, especially for NBR-rich blends. Dynamic mechanical studies showed that more compatible behavior was observed for NBR-rich blends. The 25/75 NR/NBR blend nanocomposite showed the best mechanical properties.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.05b
• /
• pp.165-170
• /
• 1997

Samples of extruded dispersions of 24 vol.% spherical U-2wt%Mo and U-10wt.%Mo powders in an aluminum matrix were annealed for over 2,000 hours at 40$0^{\circ}C$. No significant dimensional changes occurred in the U-1025.%Mo/aluminum dispersions. The U-2wt.%Mo/aluminum dispersion, however, increased in volume by 26% after 2,000 hours at 40$0^{\circ}C$. This large volume change is mainly due to the formation of voids and cracks resulting from nearly complete interdiffusion of U-Mo and aluminum. Interdiffusion between U-10wt.%Mo and aluminum was found to be minimal. The different diffusion behavior is primarily due to the fact that U-2wt.%Mo decomposes from an as-atomized metastable r-phase(bcc) solid solution into the equilibrium r-U and U$_2$Mo two-phase structure during the experiment, whereas U-10wt.%Mo retains the metastable r-phase structure after the 2,000 hours anneal and thereby displays superior thermal compatibility with aluminum compared to U-2wt.%Mo. In addition, the molybdenium supersaturated in U-10wt.%Mo particles inhibits the diffusion of aluminum atoms along the grain boundary into the particle. Also, the dissolution of only a few Mo atoms in UAL$_3$ retards the formation of the intermediate phase, as Mo atoms need to migrate from new intermetallic compounds to unreacted islands.

• Elastomers and Composites
• /
• v.56 no.3
• /
• pp.179-186
• /
• 2021

Carbon-based nanofillers, including nanodiamond (ND) and carbon nanotubes (CNTs), have been employed in epoxy matrixes for improving the toughness, using the tow prepreg method, of epoxy compounds for high pressure tanks. The reinforcing performance was compared with those of commercially available toughening fillers, including carboxyl-terminated butadiene acrylonitrile (CTBN) and block copolymers, such as poly(methyl methacrylate)-b-poly(butyl acrylate)-b-poly(methyl methacrylate) (BA-b-MMA). CTNB improved the mechanical performance at a relatively high filler loading of ~5 phr. Nanosized BA-b-MMA showed improved performance at a lower filler loading of ~2 phr. However, the mechanical properties deteriorated at a higher loading of ~5 phr because of the formation of larger aggregates. ND showed no significant improvement in mechanical properties because of aggregate formation. In contrast, surface-treated ND with epoxidized hydroxyl-terminated polybutadiene considerably improved the mechanical properties, notably the impact strength, because of more uniform dispersion of particles in the epoxy matrix. CNTs noticeably improved the flexural strength and impact strength at a filler loading of 0.5 phr. However, the improvements were lost with further addition of fillers because of CNT aggregation.

• Journal of the Society of Naval Architects of Korea
• /
• v.58 no.1
• /
• pp.40-48
• /
• 2021

Through a series of bollard pull tests of a propeller in partially submerged condition, thrust, torque, and shaft excitation force of a conventional propeller model were measured using a six-component load cell. By variation of the Weber number and Reynolds number, a consistent towing tank model test condition was derived. The effects of propeller immersion depth on the ventilation behavior and change of force and moment acting onto the propeller shaft were investigated. The decrease in thrust owing to the inception of ventilation was confirmed, and a large degree of dispersion of the thrust and torque coefficients were also observed in the transition region where the blade tip was under the water surface. The shaft excitation force was derived from the force and moment onto the propeller shaft.

• Journal of Powder Materials
• /
• v.26 no.1
• /
• pp.1-5
• /
• 2019

In this study, porous Mo-5 wt% Cu with unidirectionally aligned pores is prepared by freeze drying of camphene slurry with $MoO_3-CuO$ powders. Unidirectional freezing of camphene slurry with dispersion stability is conducted at $-25^{\circ}C$, and pores in the frozen specimens are generated by sublimation of the camphene crystals. The green bodies are hydrogen-reduced at $750^{\circ}C$ and sintered at $1000^{\circ}C$ for 1 h. X-ray diffraction analysis reveals that $MoO_3-CuO$ composite powders are completely converted to a Mo-and-Cu phase without any reaction phases by hydrogen reduction. The sintered bodies with the Mo-Cu phase show large and aligned parallel pores to the camphene growth direction as well as small pores in the internal walls of large pores. The pore size and porosity decrease with increasing composite powder content from 5 to 10 vol%. The change of pore characteristics is explained by the degree of powder rearrangement in slurry and the accumulation behavior of powders in the interdendritic spaces of solidified camphene.

• Korean Chemical Engineering Research
• /
• v.56 no.6
• /
• pp.811-818
• /
• 2018

A fire and explosion accident caused by a liquefied petroleum gas (LPG) welding and cutting torch gas leak occurred 10 m underground at the site of reinforcement work for bridge columns, killing four people and seriously injuring ten. We conducted a comprehensive investigation into the accident to identify the fundamental causes of the explosion by analyzing the structure of the construction site and the properties of propane, which was the main component of LPG welding and cutting work used at the site. The range between the lower and upper explosion limits of leaking LPG for welding and cutting work was examined using Le Chatelier's formula; the behavior of LPG concentration change, which included dispersion and concentration change, was analyzed using the fire dynamic simulator (FDS). We concluded that the primary cause of the accident was combustible LPG that leaked from a welding and cutting torch and formed a explosion range between the lower and upper limits. When the LPG contacted the flame of the welding and cutting torch, LPG explosion occurred. The LPG explosion power calculation was verified by the blast effect computation program developed by the Department of Defense Explosive Safety Board (DDESB). According to the fire simulation results, we concluded that the welding and cutting torch LPG leak caused the gas explosion. This study is useful for safety management to prevent accidents caused by LPG welding and cutting work at construction sites.

• Korean Journal of Materials Research
• /
• v.31 no.12
• /
• pp.657-664
• /
• 2021

To build a highly active photocatalytic system with high efficiency and low cast of TiO₂, we report a facile hydrothermal technique to synthesize Ag₂Se-nanoparticle-modified TiO₂ composites. The physical characteristics of these samples are analyzed by X-ray diffraction, scanning electron microscopy with energy dispersive X-ray analysis, transmission electron microscopy and BET analysis. The XRD and TEM results show us that TiO₂ is coupled with small sized Ag₂Se nanoplate, which has an average grain size of about 30 nm in diameter. The agglomeration of Ag₂Se nanoparticles is improved by the hydrothermal process, with dispersion improvement of the Ag₂Se@TiO₂ nanocomposite. Texbrite BA-L is selected as a simulated dye to study the photodegradation behavior of as-prepared samples under visible light radiation. A significant enhancement of about two times the photodegradation rate is observed for the Ag₂Se@TiO₂ nanocomposite compared with the control sample P25 and as-prepared TiO₂. Long-term stability of Ag₂Se@TiO₂ is observed via ten iterations of recycling experiments under visible light irradiation.

• Proceedings of the IEEK Conference
• /
• 2000.06b
• /
• pp.16-19
• /
• 2000

DC and low frequency noise characteristics of InGaP/InGaAs pseudomorphic HEMTs (p-HEMTs) grown by compound source MBE are investigated for temperature range of 150K to 370K. Equivalent input noise spectra( $S_{iv}$ ) were measured as a function of frequency and temperature. $S_{iv}$ was measured to be 3.4 $\times$ 10$^{-12}$ $V^2$/ Hz at 1kHz for 1.3 X 50${\mu}{\textrm}{m}$$^2$InGaP/InGaAs p-HEMT at room temperature. Measurements of the low-frequency noise spectra of the p-HEMT as a function of temperature show that the trap with an activation energy level around 0.589 eV is a dominant trap that accounts for the low-frequency noise behavior of the device. The normalized extrinsic gm frequency dispersion of the p-HEMT. was as low as 2.5％ at room temperature, indicating that the device has well-behaved low-frequency noise characteristics. Sub-micron (0.25 $\times$ 50${\mu}{\textrm}{m}$$^2$) gate p-HEMT showed $f_{T}$ and $f_{max}$ of 40GHz and 108GHz, respectively.y.y.

• Journal of the Korea Institute of Building Construction
• /
• v.23 no.4
• /
• pp.381-392
• /
• 2023

This research scrutinizes the mechanical characteristics of ultra-high strength concrete using oxide graphene nanoplatelet(GO) and hollow glass powder(HGP). The investigation covered various mechanical attributes, including workability, compression strength, tensile strength, water resistance, and the internal microstructure of standard concrete. Our findings reveal that workability experiences a significant improvement with the incorporation of a minimal amount of HGP, and an increase was also observed in tensile strength and water resistance. It was confirmed that cGO(C company GO) and HGP demonstrated commendable dispersion and the pore volume exhibited a reduction of more than 20%. The potential of cGO and HGP to substitute silica fume(SF) was also explored. Consequently, it was found that both workability and mechanical properties were enhanced in the absence of SF when cGO and HGP were used. This finding implies that the utilization of these novel materials could potentially modify conventional methods of concrete manufacturing.

• Applied Chemistry for Engineering
• /
• v.8 no.5
• /
• pp.816-821
• /
• 1997

The hydrodynamics and the liquid flow characteristics were investigated in an internal circulation airlift reactor with a single nozzle as a gas distributor. In an air-water system, the gas holdup in the individual flow zone and the impulse-response curve of tracer were measured at various gas velocities and reactor heights. Experimental results showed that for the higher gas velocity(>about 8 cm/s), the flow behavior of bubbles in the riser was turbulent flow due to strong bubble coalescences and the axial height of dispersion zone of large bubbles having uniform sizes in the downcomer was decreased with increasing gas velocity. And mean gas holdups in the individual flow zone and the reactor were increased with increasing gas velocities and were decreased with increasing heights of the top section of the reactor and it was decreased with increasing the height of the top section and gas velocity. Flow characteristics of liquid in the riser and the downcomer was tend to access to plug flow and the overall flow behavior of liquid was mainly varied with the size of the top section which it was assumed to be perfect mixing zone. In these conditions, liquid circulation velocities were increased with increasing gas velocities and they were higher than those by using other gas distributors.