• Journal of the Korean Applied Science and Technology
• /
• v.12 no.1
• /
• pp.59-67
• /
• 1995

Oil dispersants using polyoxyethylene monooleate, polyoxyethylene oleylether, and poly(oxypropylene-oxyethylene)glycol block copolymer were prepared, and oil dispersant efficiency was measured using vertical shaking flask method to 4 kinds of Bunker B oil with different physical properties by appling the prepared dispersants. Although the dispersant efficiency was differed according to the differences of physical properties of Bunker B oil, the dispersant prepared using polyoxyethylene oleylether was the most effective to disperse the oil into water. The impurities like surfur contained in sample oil have to be removed by filteration to obtain the correct degree of absorption using UV spectrophotometer.

• Applied Chemistry for Engineering
• /
• v.18 no.5
• /
• pp.490-494
• /
• 2007

Dispersants were prepared from petroleum pyrolysis residual oil (PPRO) through sulfonation. Without employing a conventional polynaphthalene sulfonate formaldehyde condensate (PNS) process, the dispersants (NPS) were synthesized by a simpler process only in 2 h. The chemical structure of new dispersant, which has various naphthalene derivative groups, was similar to PNS conformed by UV-visible spectroscopy curves. The new dispersants demonstrated high dispersing ability in inorganic suspension ; cement, $Fe_2O_3$, and $CaCO_3$.

• Elastomers and Composites
• /
• v.55 no.3
• /
• pp.215-221
• /
• 2020

Silica/SBR (styrene-butadiene rubber) compounds are the primary constituents of tire treads. Furthermore, the excellent dynamic viscoelastic properties of silica lead to good fuel efficiencies. However, the silanol group on the surface of silica does not mix well with non-polar rubber because of its polarity. This incompatibility causes aggregation due to the occurrence of hydrogen bonding between the hydroxyl groups, thereby reducing the dispersibility of silica. Recently, the wet master batch (WMB) process has been applied to overcome these disadvantages, and research on silica dispersants that can be used in the WMB process has been increasing. In this study, we prepared silica/SBR compounds by using three types of eco-friendly cellulose-based dispersants in the WMB process, namely: cellulose-, sodium carboxymethyl cellulose, and nanocellulose-based dispersants. Subsequently, we compared the vulcanization characteristics, viscoelastic properties, and mechanical properties of the compounds. The silica dispersibility in the rubber compounds was improved with the addition of the nano-cellulose dispersant, resulting in the enhancement of the workability, hardness, tensile strength, and wear resistance of the SBR compound.

• Cement Symposium
• /
• no.23
• /
• pp.232-238
• /
• 1995

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.4
• /
• pp.341-347
• /
• 2008

Laminated LTCC components of high integrity, fabricated by thick film process, are applied to industrial field of IT technology along with miniaturization trend of electronic devices. Dispersion states were examined by several evaluation methods with MLS-22, which is one of commercial LTCC powders, to achieve optimal dispersion as basis for stable LTCC fabrication process. Slurry viscosity, surface roughness of dip-coated slide glass, sedimentaion of slurry, and SEM observation of dried surface were utilized with respective amount change of various commercial dispersants. Among these commercial dispersants, optimal dispersion state was obtained with 0.4 wt% of BYK-111, from the results of various evaluation methods.

• Journal of the Korean institute of surface engineering
• /
• v.48 no.4
• /
• pp.158-162
• /
• 2015

To substitute indium tin oxide (ITO), many substituents have been studied such as metal nanowires, carbon based materials, 2D materials, and conducting polymers. These materials are not good enough to apply to an electrode because theses exhibit relatively high resistance. So metal grids are required as an additionalelectrode to improve the conductivities of substituents. The metal grids were printed by electrohydrodynamic printing system using Ag nanoparticle based ink. The Ag grids showed high uniformity and the line width was about $10{\mu}m$. The Ag nanoparticles are surrounded by dispersants such as unimolecular and polymer to prevent aggregation between Ag nanoparticles. The dispersants lead to low conductivity of Ag grids. Thus, the sintering process of Ag nanoparticles is strongly recommended to remove dispersants and connect each nanoparticles. For sintering process, the interface and microstructure of the Ag grid were controlled in 1.0 torr Ar atmosphere at aound $400^{\circ}C$ of temperature. From the sintering process, the uniformity of the Ag grid was improved and the defects on the Ag grids were reduced. As a result, the resistivity of Ag grid was greatly reduced up to $5.03({\pm}0.10){\times}10^{-6}{\Omega}{\cdot}cm$. The metal grids embedded substrates containing low pressure Ar sintered Ag grids showed 90.4% of transmittance in visible range with $0.43{\Omega}/{\square}$ of sheet resistance.

• Polymer(Korea)
• /
• v.33 no.5
• /
• pp.397-406
• /
• 2009

We have fabricated source-drain electrodes for OTFTs using a screen-printing technique with carbon-black pastes as conductive paste. And effects of dispersants contents (SOP 10-40%) on the dispersity of carbon-black pastes and characteristics of screen-printed source-drain electrodes for OTFTs using two types of dispersants (DB-2150, DB-9077) were investigated. As contents of both dispersants were increased the dispersity of carbon-black mill-bases was improved, whereas the carbon-black pastes exhibited different dispersion characteristics. For the case of DB-2150, the dispersity of the pastes was improved with increasing dispersant content and the storage modulus G' in their rheology characteristics were reduced. But, for the DB-9077, the storage modulus G' of pastes were increased with dispersant content due to the flocculated network structure formed by interactions among carbon-black powders and dispersants. But, since this flocculated network structure of the pastes using DB-9077 resulted in the conduction path of carbon-black structures, the conductivities of screen-printed electrodes and mobilities of the OTFTs with them were better than those using pastes with DB-2150.

• Journal of the Korean Ceramic Society
• /
• v.33 no.10
• /
• pp.1109-1116
• /
• 1996

• Proceedings of the Korean Magnestics Society Conference
• /
• 1993.03a
• /
• pp.42-43
• /
• 1993

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.10a
• /
• pp.74.1-74
• /
• 2003