• Tribology and Lubricants
• /
• 제23권1호
• /
• pp.19-28
• /
• 2007

Mechanical Brake system is inevitable equipment for stability of train and speed of the train. Especially brake disk and brake pads are core parts of mechanical brake system. It was investigated with tribological characteristics of brake discs for train by using lab-scale dynamometer. Gray cast iron disk was most attacked with sintered brake pad. Alloyed steel disk and NCM cast iron disk had suitable friction coefficient, high stability and low disk attack to the sintered brake pad. But at the view of economy, low alloyed cast iron will be most suitable choice.

• Tribology and Lubricants
• /
• 제29권1호
• /
• pp.19-26
• /
• 2013

Cu-matrix sintered brake pads and low-alloy heat-resistant steel are commonly applied to basic brake systems in high-energy moving machines. In this research, we analyzed the tribological characteristics to determine the influence of the air velocity between the disk and pad. At a low brake pressure with airflow, the friction stability was decreased as a result of the lack of tribofilm formation at the disk surface. However, there were no significant changes in the friction coefficient under any of the test conditions. The wear rates of the friction materials were decreased with an increase in the airflow velocity. As a result, the airflow velocity influenced the friction stability, as well as the wear rate of the friction materials and disk, but not the friction coefficient.

• 한국가시화정보학회지
• /
• 제20권1호
• /
• pp.18-28
• /
• 2022

In this study, a cavity shape measurement experiment was conducted by changing the diameter and the angle of attack of a disk cavitator. Since the gravity effect is proportional to the cavity volume, the larger the cavity, the greater the effect. It is concluded that the gravity effect becomes smaller as the cavitation number decreases because of a short cavity maintaining time. The cavity centerline rises in case of the positive angle of attack and descends in case of the negative angle of attack. Since the effect of the angle of attack is inversely proportional to the square of the cavity radius, the effect of the angle of attack becomes dominant in the vicinity of the cavitator. It is judged that the horizontal section of the cavity centerline cannot be extended because the factors affecting the gravity effect and the angle of attack effect are different.

• Tribology and Lubricants
• /
• 제29권2호
• /
• pp.98-104
• /
• 2013

Cu-matrix-sintered brake pads and heat-resistant low-alloy steel are commonly applied to basic brake systems in high-energy moving machines. We analyzed how the tribological characteristics are influenced by the inertial mass. A high inertial mass decreased the friction coefficient by about 15% compared to a low inertial mass under all velocity conditions. The wear rates of the friction materials increased with the inertial mass. Thus, the inertial mass influences the friction coefficient and wear rate of the friction materials and disk but not the friction stability.

• Tribology and Lubricants
• /
• 제27권1호
• /
• pp.19-24
• /
• 2011

Metallic sintered brake pads are often applied to mid/high speed train due to their high strength and thermal characteristics. Imbalance contact between discs and pads can greatly influence the life span, one sided wear, discs attack/crack and threat the safety of the train during operation. In this research, we analyzed pressure/temperature distribution between brake pads and disks. Analyzed data had been verified and modified to conduct further tests of flexible brake pads with small/full-scale dynamo test. Flexible brake pads were installed to high speed train to conduct further tests to identify the differences between rigid brake pads and flexible brake pads. In result, Flexible brake pads showed outstanding disk thermal stability, one sided wear, noise and wear rate than rigid brake pad.

• 한국항공우주학회지
• /
• 제41권6호
• /
• pp.429-439
• /
• 2013

본 연구에서는 로터 성능 해석을 위한 로터 성능 해석자를 개발하고 이를 사용하여 방풍 구조물 내부의 로터 성능 해석을 수행하였다. 로터 성능 해석자는 깃요소 이론 기반의 actuator disk model을 사용한 해석자를 사용하였다. 또한, 주변의 구조물로 인한 로터 하중의 비대칭성을 고려하기 위해 깃요소 이론에서 블레이드의 flapping 운동에 대한 해석을 수행하여 유효받음각 계산에 적용하였다. 개발된 해석자를 사용하여 바닥면과 벽면에 의한 로터 성능 변화에 관한 연구와 비교 검증을 수행하였다. 방풍 구조물 형상에 따른 로터 성능 해석을 통해 방풍 구조물에 의한 로터 성능 감소 현상을 확인하였다. 이를 통해 방풍 구조물이 없는 경우 대비 95% 이상의 로터 성능 비를 가지는 방풍 구조물의 유출입덕트 면적을 제안하였다.

• 대한조선학회논문집
• /
• 제60권4호
• /
• pp.240-247
• /
• 2023

In this study, morphological and hydrodynamic characteristics of the non-axisymmetric supercavity generated behind a disk-shaped cavitator were examined. By extending the previous study on axisymmetric supercavitating flow based on a boundary element method, hydrodynamic forces acting under the angle of attack condition of 0 to 30 ° and shape characteristics of the supercavity were analyzed. The results revealed that increasing the angle of attack by 30 ° reduced the length and width of the cavity by about 15% and the volume by about 40 %. An empirical formula that can quantitatively estimate the geometrical characteristics and change of the cavity was derived. It is expected that this method can be used to evaluate the shape information and force characteristics of the supercavity for the control of the vehicle in a very short time compared to the viscous analysis in the initial design stage of the supercavity underwater vehicle.

• 한국항공우주학회지
• /
• 제39권12호
• /
• pp.1087-1096
• /
• 2011

본 연구의 목적은 오픈 소스 코드에서 제공하는 해석자의 알고리즘을 수정하여 로터의 유동 해석에 적합하도록 해석자를 확장하고, 이를 검증하는 것이다. 우선 로터의 추력에 의해 발생하는 후류에 의한 유동 흐름의 해석이 가능하도록 오픈 소스 코드인 OpenFOAM의 표준 해석자의 알고리즘을 개선하였다. 또한, 로터의 추력 예측을 위해서 깃요소 이론을 기반으로 한 가상 블레이드 기법을 적용하였다. 깃요소 이론에서의 유효받음각을 구하기 위한 로터 디스크 상의 속도 성분은 해석자 내에서 반복계산시마다 수렴되는 속도를 사용하였다. 개발된 로터 해석자를 사용하여 로터 유입류 해석을 수행하고 그 결과를 실험 결과 및 타 수치해석 코드의 결과와 비교하여 신뢰도를 검증하였다. 로터-동체 상호작용 해석을 통해 헬리콥터 시스템 전체에 대한 로터 해석자의 적용가능성을 확인하였다.

• 대한조선학회논문집
• /
• 제56권6호
• /
• pp.541-549
• /
• 2019

In the present study, we investigated planing forces of supercavitated bodies by using the supercavitation shape produced by the disk type cavitator. The cavity shapes are observed to find the immersion draft and planing angle when the stern of the supercavitated body is partially immersed in the water. To make the planing the angle-of-attack (AOA) of the supercavitated body is varied statically against the main flow and the planing tests are carried out for different body shapes that are changed systematically. The drag, lift and pitch moment acting on the body are measured to understand the relation between the planing force and the immersion draft of the supercavitated body. It is found that the planing force increased in general linearly with the immersion draft ratio and the planing angle is certainly not proportional to the immersion draft ratio.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2007년도 추계 학술대회논문집
• /
• pp.264-271
• /
• 2007

The flow simulations around ducted-prop of tilt-duct aircraft were conducted in this study. For the investigation of aerodynamic characteristics of various configurations of duct, the axisymmetric flow calculation method combined with actuator disk model for prop were used. The rapid two-dimensional calculation and fast grid generation enable aerodynamic analysis for various duct configurations in a very short time and anticipated to active role in optimal configuration design of duct exposed to various flight modes. For the case of angle of attack or tilt angle, the three dimensional flow calculation is conducted using the three dimensional grid simply generated by just revolving the axisymmetric grid around center axis. Through the three dimensional calculation around duct, the aerodynamic effectiveness of duct as a lifting surface in airplane mode was investigated. The flow calculations around the control vane (wing) installed in the rear section of duct were conducted The aerodynamic data of wing were compared with the data of the ducts to evaluate the aerodynamic effectiveness of ducts.