• Journal of the Korea Concrete Institute
• /
• v.14 no.6
• /
• pp.934-941
• /
• 2002

It is important to consider the effect of member size when estimating the ultimate strength of a concrete flexural member because the strength always decreases with an increase of member size. In this study, the size effect of a reinforced concrete (RC) beam was experimentally investigated. For this purpose, a series of beam specimens subjected to four-point loading were tested. More specifically, three different effective depth (d$\approx$15, 30, and 60 cm) reinforced concrete beams were tested to investigate the size effect. The shear-span to depth ratio (a/d=3) and thickness (20 cm) of the specimens were kept constant where the size effect in out-of-plane direction is not considered. The test results are curve fitted using least square method (LSM) to obtain parameters for the modified size effect law (MSEL). The analysis results show that the flexural compressive strength and the ultimate strain decrease as the specimen size increases. In the future study, since $\beta_1$ value suggested by design code and ultimate strain change with specimen size variation, a more detailed analysis should be performed. Finally, parameters for MSEL are also suggested.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.4
• /
• pp.506-519
• /
• 1999

An adaptive array antennal and a CCI canceller have been considered as techniques for cancelling Multi-User Interference(MUI) in Direct Sequence Code Division Multiple Access(DS-CDMA) system. These techniques have different problems respectively in the process of cancelling MUI as the number of users increases. For that reason, the scheme which can cancel MUI effectively by compensating for the problems of each of the techniques has been required. For the scheme, the technique to connect an adaptive array antenna and a CoChannel Interference(CCI) canceller in cascade form has been studied. In the existing study about the cascade connection method, the effect of cancelling MUI about two interference signals is analyzed, but the analysis for the quantitative BER(Bit Error Rate) improvement according to the number of users is not considered. Therefore, in this paper, we have analyzed the degree of BER performance improvement quantitatively according to the number of users by introducing the receiving system, which connects an adaptive array antenna and a CCI canceller to a DS-CDMA system in cascade form. For the method of analyzing the performance, we have performed the theoretical analysis and the simulation, considering the case of adopting only an adaptive array antenna and of cascade connection respectively, and having compared and analyzed the results. From the results, it is confirmed that in the case of adopting only an adaptive array antenna, the problems occur in the process of cancelling MUI according to the number of users and the receiving direction of interference signals, and can be compensated by the cascade connection method. In conclusion, we have known that MUI is cancelled effectively by using the cascade connection method, and the much better BER performance improvement is obtained.

• The Journal of the Acoustical Society of Korea
• /
• v.37 no.5
• /
• pp.263-270
• /
• 2018

In most industry fields concerning external flow noise problems, the hybrid computational aeroacoustic techniques based on the FW-H (Ffowcs Williams and Hawkings) equation are widely used for its numerical efficiency. However, when the surface integral form of FW-H equation is used without volume quadrupole sources, it is known to generate significant non-physical noise in a certain case. Especially, in the case of a flow in which the tip vortex cavitation is formed in the distant downstream direction such as flow driven by an underwater propeller, the accuracy in noise prediction becomes poor unless it is not properly modelled. Therefore, in this study, the nonphysical acoustic waves caused by the surface integral form of FW-H equation is reduced by adding the quadrupole correction term. First, to verify the accuracy of the in-house code of FW-H equation, the noise by an axial fan used in the outdoor unit of air conditioner was calculated and compared with the results of ANSYS Fluent. In order to verify the effects of the quadrupole correction term, the noise prediction for isentropic vortex convection is performed and it is confirmed that the error is reduced by the quadrupole correction term. Finally, the noise prediction is performed for the flow field generated by the Clark-Y hydrofoil in underwater. It is confirmed that the error caused by the cavitation passing through the integral surface can be reduced by the quadrupole correction term.

• Journal of Korean Library and Information Science Society
• /
• v.43 no.3
• /
• pp.5-26
• /
• 2012

This study is to find the new method for authority control in Korea by surveying status of authority control in university libraries and by analyzing international conceptual model of authority control and VIAF. 2 kinds of survey were done: one is for libraries having authority records and the other is for libraries not having authority records. In survey result, libraries that have authority records want to sustain their own forms of authorized access points and libraries that have no authority records want the rules related to authority and the national cooperative authority control system to be constructed. Based on ICP 2009, FRAD conceptual model, VIAF and this survey result, new authority control is to respect the diversity of forms of the authorized access points. New authority control is to permit authority records that reflect provision for linguistic or cultural environments of each library, confirming to the national cataloging code. Therefore, authorized access points will be displayed according to user preferred forms. For this new authority control, it is needed to make national authority rule, to build the authority records according to library's own rules, and to construct the cooperative authority control system. Also for user preferred authority control, it is needed to describe detailed elements for authority control and relation data between authorized access points, between authorized access points and variant forms. This study could contribute to suggest new authority control that could accept all kinds of authorized access points preferred by nation, libraries, and users.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.3
• /
• pp.197-209
• /
• 2018

In this study, numerical analyses on Quad Tilt Rotor(QTR) are carried out to investigate the interference effect of components and effect of operating condition during forward flight. Actuator Surface Method(ASM) which is implemented in an open source CFD code, OpenFOAM, is used to calculate the flow field around QTR with high computational efficiency. The lift of the front and rear wing is found to increase or decrease depending on the rotation direction of the rotor. At the rear wing, the interference effects of the front and rear rotor appear as a combined manner. Performance change due to the phase difference is found to be insignificant. For both rotors, the locally higher thrust is generated by the blockage effect of the wing. The interference effect of wake from the front nacelle contributes to higher local thrust for the rear rotor compared to the front rotor. And it is observed that the amplitude of thrust oscillation can decrease depending on the phase difference between the rotors. Aerodynamic performances of both rotors and the entire aircraft were compared and analyzed for various operating conditions.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.69-76
• /
• 2018

The present study analyzed the effect of film hole position of 45 degree ribbed cooling channel on film cooling performance of gas turbine blades. We also investigated the influence of the ribs under the fixed blowing ratio. Three-dimensional numerical model was constructed and extensive simulation was conducted using the commercial code (Fluent ver. 17.0) under steady-state condition. Base on the simulation results, We investigated the cooling effectiveness, flow velocity, streamline, and pressure coefficient. Moreover, We analyzed the effect of cooling hole position on ejection of the secondary flow caused by the rib structure. From the results, It was found that internal flow of the cooling channel forms a vortex pair in the counterclockwise from the top side, and clockwise from the bottom side. For the channels with ribs, the vortex flow generated by the ribs caused a higher pressure difference near the hole outlet, resulting in at least 12% higher cooling effectiveness than the channel without ribs. Additionally, when the hole is located on the left side of the ribbed channel (Rib-Left), it can be found that the secondary flow generated by the ribs hits against wall surface near the hole to form a flow in the direction of the hole inclination angle. Therefore, It is considered that the region where the cooling gas discharged to the blade surface stays in the main flow boundary layer is wider than the other cases. In this case, The largest pressure coefficient difference was observed near the outlet of the hole, and as a result, the discharge of the cooling gas was accelerated and the cooling efficiency was slightly increased.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.3
• /
• pp.171-178
• /
• 2014

From now on, in order to meet more stringer diesel emission standard, diesel vehicle should be equipped with emission after-treatment devices as NOx reduction catalyst and particulate filters. Urea-SCR is being developed as the most efficient method of reducing NOx emissions in the after-treatment devices of diesel engines, and recent studies have begun to mount the urea-SCR device for diesel passenger cars and light duty vehicles. That is because their operational characteristics are quite different from heavy duty vehicles, urea solution injection should be changed with other conditions. Therefore, the number and diameter of the nozzle, injection directions, mounting positions in front of the catalytic converter are important design factors. In this study, major design parameters concerning urea solution injection in front of SCR are optimized by using a CFD analysis and Taguchi method. The computational prediction of internal flow and spray characteristics in front of SCR was carried out by using STAR-CCM+7.06 code that used to evaluate $NH_3$ uniformity index($NH_3$ UI). The design parameters are optimized by using the $L_{16}$ orthogonal array and small-the-better characteristics of the Taguchi method. As a result, the optimal values are confirmed to be valid in 95% confidence and 5% significance level through analysis of variance(ANOVA). The compared maximize $NH_3$ UI and activation time($NH_3$ UI 0.82) are numerically confirmed that the optimal model provides better conversion efficiency of $NH_3$. In addition, we propose a method to minimize wall-wetting around the urea injector in order to prevent injector blocks caused by solid urea loading. Consequently, the thickness reduction of fluid film in front of mixer is numerically confirmed through the mounting mixer and correcting injection direction by using the trial and error method.

• Cartoon and Animation Studies
• /
• s.49
• /
• pp.247-265
• /
• 2017

With the increasingly diverse, sophisticated and complex character animations that can be represented in 3D animations, the importance of rigging, which can most directly affect animating quality, is becoming more and more important. In addition, rapidity is another crucial aspect of 3D animation production. So, the importance of technical director's role which is accurate and rapid handling of rigging pipeline building and immediate application and, corrections of errors during the longest and manpower consuming animation production is more becoming key. Baek Ji Won and Kim Jae-woong (2014) said, "The technical director is adding new importance to the new job, which is created by 3D animation, in conjunction with the limited production period, manpower, budget and production process." Most major overseas studios are developing in-house software to handle rigging and animation processes. Software development code is used to freely develop and modify production pipelines in accordance with the direction of the work. They are making efforts to build an optimal environment for animators. However, too many efforts and ineffective efforts have been made to develop, adapt, and stabilize the rigging process for small producers, creators, and students who do not have the capacity to develop their own in-house software or hire a technical director. This study suggests the most suitable auto-rigging tool among the many auto-rigging tools released in the market, and suggests the most accurate and quick auto-rigging process setting method for those who have insufficient knowledge about 3D character rigging. The efficiency of use of auto-rigging tool was examined.

• Radiation Oncology Journal
• /
• v.21 no.2
• /
• pp.158-166
• /
• 2003

Purpose: To propose a conceptual design of a novel source for intensity modulated brachytherapy. Materials and Methods: The source design incorporates both radioactive and shielding materials (stainless steel or tungsten), to provide an asymmetric dose intensity in the azimuthal direction. The intensity modulated intravascular brachytherapy was performed by combining a series of dwell positions and times, distributed along the azimuthal coordinates. Two simple designs for the beta-emitting sources, with similar physical dimensions to a $^{90}Sr/Y$ Novoste Beat-Cath source, were considered in the dosimetric feasibility study. In the first design, the radioactive and materials each occupy half of the cylinder and in the second, the radioactive material occupies only a quater of the cylinder. The radial and azimuthal dose distributions around each source were calculated using the MCNP Monte Carlo code. Results: The preliminary hypothetical simulation and optimization results demonstrated the 87$\%$ difference between the maximum and minimum doses to the lumen wall, due to off-centering of the radiation source, could be reduced to less than 7$\%$ by optimizing the azimuthal dwell positions and times of the partially shielded intravascular brachytherapy sources. Conclusion: The novel brachytherapy source design, and conceptual source delivery system, proposed in this study show promising dosimetric characteristics for the realization of intensity modulated brachytherapy in intravascular treatment. Further development of this concept will center on building a delivery system that can precisely control the angular motion of a radiation source in a small-diameter catheter.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.28 no.6
• /
• pp.332-349
• /
• 2016

OLAFOAM is the powerful CFD code and is an expanded version of $OpenFOAM^{(R)}$, for wave mechanics simulation. The $OpenFOAM^{(R)}$ does provide many solvers to correspond to each object of the numerical calculation in a variety of fields. OLAFOAM's governing equation bases on VARANS (Volume-Averaged Reynolds-Averaged Navier-Stokes) equation, and the finite volume method is applied to numerical techniques. The program is coded in C++ and run on the Linux operating system. First of all, in this study, OLAFOAM was validated for 1) wave transformation inside porous structure under bore and regular wave conditions, 2) wave transformation by submerged breakwater under regular wave condition, and 3) regular wave transformation and resultant vertical velocity distribution under current by comparison with existing laboratory measurements. Hereafter, this study, which is almost no examination carried out until now, analyzed closely variation characteristics of water surface level, wave height, frequency spectrum, breaking waves, averaged velocity and turbulent kinetic energy around porous submerged breakwater in the wave and current coexisting field for the case of permeable or impermeable rear beach. It was revealed that the wave height fluctuation according to current direction(following or opposing) was closely related to the turbulent kinetic energy, and others.