• 소성∙가공
• /
• 제25권2호
• /
• pp.91-95
• /
• 2016

This paper is concerned with modeling of a ductile fracture criterion for sheet metal considering anisotropy to predict the sudden fracture of advanced high strength steel (AHSS) sheets during complicated forming processes. The Lou−Huh ductile fracture criterion is modified using the Hill’s 48 anisotropic plastic potential instead of the von Mises isotropic plastic potential to take account of the influence of anisotropy on the equivalent plastic strain at the onset of fracture. To determine the coefficients of the model proposed, a two dimensional digital image correlation (2D-DIC) method is utilized to measure the strain histories on the surface of three different types of specimens during deformation. For the derivation of an anisotropic ductile fracture model, principal stresses (𝜎₁,𝜎₂, 𝜎₃) are expressed in terms of the stress triaxiality, the Lode parameter, and the equivalent stress (𝜂_𝐻, 𝐿,) based on the Hill’s 48 anisotropic plastic potential. The proposed anisotropic ductile fracture criterion was quantitatively evaluated according to various directions of the maximum principal stress. Fracture forming limit diagrams were also constructed to evaluate the forming limit in sheet metal forming of AHSS sheets over a wide range of loading conditions.

• International Journal of Concrete Structures and Materials
• /
• 제10권1호
• /
• pp.75-85
• /
• 2016

Fire ranks high among the potential risks faced by most buildings and structures. A full understanding of temperature effects on fiber reinforced concrete is still lacking. This investigation focuses on the study of the residual compressive strength, stress strain behavior and surface cracking of structural polypropylene fiber-reinforced concrete subjected to temperatures up to $300^{\circ}C$. A total of 48 cubes was cast with different fiber dosages and tested under compression after exposing to different temperatures. Concrete cubes with varying macro (structural) fiber dosages were exposed to different temperatures and tested to observe the stress-strain behavior. Digital image correlation, an advanced non-contacting method was used for measuring the strain. Trends in the relative residual strengths with respect to different fiber dosages indicate an improvement up to 15 % in the ultimate compressive strengths at all exposure temperatures. The stress-strain curves show an improvement in post peak behavior with increasing fiber dosage at all exposure temperatures considered in this study.

• 소성∙가공
• /
• 제32권6호
• /
• pp.321-328
• /
• 2023

To ensure driver safety, high-strength steel pipes are utilized in the chassis and internal structures design of automobiles. ERW(electric resistance welding) pipes, fabricated through welding at joints using electrical resistance, form a Heat-Affected Zone (HAZ) during the welding process. Due to characteristics such as increased hardness and reduced ductility compared to the base material, HAZ poses challenges in finite element analysis (FEA) for pipe shapes. In this study, for FEA considering HAZ properties, mechanical properties were measured through uniaxial tensile testing and digital image correlation (DIC) techniques after specimen fabrication. These measurements were validated using reverse engineering methods. Furthermore, hardness measurements and gaussian functions were employed to ascertain the hardness distribution within the HAZ, serving as a basis for subdividing the HAZ and modeling the pipe shape. To validate the effectiveness of the HAZ modeling approach, models were interpreted incorporating only base material properties and models incorporating average-calculated HAZ properties. Comparative analysis was performed, revealing that the model subdividing the HAZ based on hardness measurements closely approximated experimental values. This validation offered a methodology for HAZ modeling in FEA.

• 드라이브 ㆍ 컨트롤
• /
• 제13권4호
• /
• pp.45-51
• /
• 2016

The power train of a hydro-mechanical, continuously variable transmission for forklifts makes use of hydro-static units, hydraulic multi-wet disc brakes & clutches, and complex helical & planetary gears. The complex helical & planetary gears are very important parts of the transmission because of a strength problem. In the present study, we calculated the specifications of the complex helical & planetary gear train, and analyzed the gear bending and compressive stresses of the gears. It is necessary to analyze the gear bending and compressive stresses thoroughly for optimal design of the complex helical & planetary gears with respect to cost and reliability. In this paper, we analyze the actual gear bending and compressive stresses of complex helical & planetary gears using the Lewes & Hertz equation, and we also verify the calculated specifications of the complex helical & planetary gears by evaluating the results of the data of allowable bending and compressive stress using the Stress vrs Number of Cycles curves of gears.

• Computers and Concrete
• /
• 제33권5호
• /
• pp.481-496
• /
• 2024

Internal erosion around pipes can lead to the failure of earth dams through various mechanisms. This study investigates the displacement patterns in earth dam models under three different failure modes due to internal erosion, using digital image correlation (DIC) methods. Three failure modes—erosion along a pipe (FM1), pipe leakage leading to soil erosion (FM2), and erosion in a pipe due to defects (FM3)—are analyzed using two- and three-dimensional image- processing techniques. The internal displacement of the cross-sectional area and the surface displacement of the downstream slope in the dam models are monitored using an image acquisition system. Physical model tests reveal that FM1 exhibits significant displacement on the upper surface of the downstream slope, FM2 shows focused displacement around the pipe defect, and FM3 demonstrates increased displacement on the upstream slope. The variations in internal and surface displacements with time depend on the segmented area and failure mode. Analyzing the relationships between internal and surface displacements using Pearson correlation coefficients reveals various displacement patterns for the segmented areas and failure modes. Therefore, the image-based characterization methods presented in this study may be useful for analyzing the displacement distribution and behavior of earth dams around pipes, and further, for understanding and predicting their failure mechanisms.

• Journal of Yeungnam Medical Science
• /
• 제3권1호
• /
• pp.375-382
• /
• 1986

We studied the effects of the acute intermittent peritoneal dialysis in severe acute renal failure of 1 newborn infant and 2 young infants during 18 months period from February 1985 to April 1986. The predisposing illnesses were severe acute gastroenteritis with dehydration. Reye's syndrome, and bilateral nephrolithiasis with hyperuricemia. The concomittent illnesses were severe hypernatremia, hyponatremia, hyperkalemia, hypocalcemia, hypoglycemia, DIC(disseminated intravascular coagulopathy), paralytic ileus, metabolic acidosis and gastrointestinal bleeding. As a dialvsate, Imperinol $solution^R$, 1.5% was used in all cases. The cycles of dialysis were 8, 16, and 41 times in each cases. Observed complications during dialysis were leakage, and abdominal wall and scrotol swelling in 2 cases, hyperglycemia in 1 case, and peritonitis in 1 case. Acinetobacter calcoaceticus was cultured in peritoneal fluid of peritonitis. These complications were treated by stopping dialysis in leakage and abdiminal wall swelling, insulin therapy in hyperglycemia, and intraperitoneal and systemic antibiotics therapy in peritonitis. We experienced improvements of severe acute renal failure with variable concomittant illnesses by acute intermittent peritoneal dialysis despite of the treatable complications of dialysis in all cases.

• 응용통계연구
• /
• 제22권6호
• /
• pp.1167-1176
• /
• 2009

항만이나 공항의 소유구조에 대한 효율성 분석은 지금까지 서로 엇갈리는 결과를 제시하고 있다. 즉, 민영화 또는 공영화로 인한 효율성 효과가 자료 또는 분석 방법에 따라서 일치된 결과를 보여주지 않고 있다. 본 논문은 국내의 항만이 포함된 국제 항만 교역데이터베이스를 기반으로 베이지안 확률적 프런티어 모형을 적용하여 항만의 소유 구조에 따른 효율성 분석을 하였다. 소유 구조는 Tongzon과 Heng (2005)의 방법을 따랐으며 제안된 몇 가지 모형과 그들의 모형을 DIC 통계량을 이용하여 비교하였다. 베이지안 추론에 필요한 MCMC 방법은 Griffin과 Steel (2007)에서 소개된 WinBUGS 프로그램을 이용하여 구현하였다.

• Journal of Chest Surgery
• /
• 제25권7호
• /
• pp.769-776
• /
• 1992

Total 632 cases of open heart surgery were performed in the department of thoracic and cardiovascular surgery, Pusan Paik Hospital, Inje University from october 1985 to december 1990. Among them, there were 503 cases of congenital heart disease and 129 cases of acquired heart disease. In the cases of 503 congenital heart disease surgically corrected, 122 cases over 15 years of age were reviewed and its results were summarized as follows ; l. In total 122 cases 65 were male and 52 female. 2. There were 54 patients under 20 years of age, 31 between 20 & 24 years, 20 between 25 & 29 and 17 over 30 years of age. The eldest was a 46-year-old female of atrial septal defect group. 3. There were 63 cases of VSD[51.7%], 38 of ASD[31.2%], 11 cases of TOF[9%] and so on. 4. In recovery cases, main post-operative complications were as follows; cardiac tamponade, arrhythmia, low cardiac output syndrome, pulmonary, edema pericarditis, mediastinitis, sepsis and DIC. 5. There were 3 cases of post-operative death in this series, so operative mortality rate was 2.5% compairing with 1.8% of pediatric cases below 15 years of age. 6. This reviewed series reveal that aggressive surgical approach in adult congenital heart disease can be justified with low operative mortality like as pediatric age group.

• 소성∙가공
• /
• 제11권6호
• /
• pp.495-502
• /
• 2002

The welding pressure in extru bending process is affected by the shape of welding chamber of porthole die. It is very important to increase the welding pressure when the tube should be extruded particulary from four billets of the materials. The high circumferential stress of the tube can make the welding pressure increase during the extru-bending. In order to increase the circumferential stress, it is necessary to make the billets pass through the narrow gap between the conical die and the conical plug. This paper describes the welding pressure by the experiments and the analysis with the two types of the chamber. One of them is the chamber between the flat die and straight mandrel, and the other one is the chamber between the conical die and conical plug. The results of the experiments and the analysis shows that the conical chamber makes the welding pressure increase by the effect of the reducing diameter of tube and the welding pressure by the conical dic and plug is stronger than the welding pressure by the flat die and straight mandrel.

• 드라이브 ㆍ 컨트롤
• /
• 제14권4호
• /
• pp.71-78
• /
• 2017

The power train of hydro-mechanical continuously variable transmission (HMCVT) for 8-ton class forklift includes hydro-static units, hydraulic multi-wet disc brake & clutches and complex helical & planetary gears. The helical & planetary gears are key components of HMCVT's power train wherein strength problems are the main concerns including gear bending stress, gear compressive stress, and scoring failure. Many failures in power train gears of HMCVT are due to the insufficient gear strength and resonance problems caused by major excitation forces, such as gear transmission error of mating gear fair in the transmission. In this study, wherein excitation frequencies are the gear tooth passing frequencies of the mating gears, a Campbell diagram is used to calculate the power train gears' critical speeds. Mode shapes and natural frequencies of the power train gears are calculated by CATIA V5. These are used to predict resonance failures by comparing the actual working speed range with the critical speeds due to the gear transmission errors of HMCVT's power train gears.