• Journal of Biosystems Engineering
• /
• v.27 no.2
• /
• pp.89-96
• /
• 2002

The trend of consumption of vegetable soybeans is increasing because they are recognized as the clean vegetable. The works requiring the most intensive labor are threshing and seperation ones, and they form about 80% of total labour for vegetable soybeans production. It is necessary to develop the vegetable soybeans-thresher for the sake of cost down of vegetable soybeans production. The purpose of this study is to acquire the basic informations to design of the vegetable soybeans-thresher. We make the experimental system which control the speed of threshing cylinder and the teeth gap and investigate the detachment forces. The result are as follows ; The ratio of un-threshed soybeans-pod to stem after threshing work is decreasing as the threshing cylinder speed increases: 0.0% and 2.8% at 55m/s and 18m/s of threshing cylinder speed respectively. Also the ratio of un-threshed soybeans-pod to stem is shown as 2.0% below in the condition of 64~160mm of teeth gap and over 28m/s of threshing cylinder speed. The damaged pod ratio of detached soybeans after threshing work is decreasing as the threshing cylinder speed increases: 4.8% and 1.3% at 55m/s and 18m/s of threshing cylinder speed respectively. The minimum damaged pod ratio of detached soybeans are shown as 1.0%, 1.5% and 1.9% at 18m/s, 28m/s and 37m/s of threshing cylinder speed respectively. The average detachment forces of pods are shown as 1.5kg$_{f}$ for 3 grains, 1.2kg$_{f}$ for 2 grains and 0.8kg$_{f}$ for 1 grain respectively. The maximum detachment force of pod is shown as 2.7kg$_{f}$ for 3 grains. grains.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.11a
• /
• pp.19-26
• /
• 2001

The wear characteristic of Zircaloy-4 tube, which is used for a cladding of light water reactor fuel rod, is investigated experimentally. The experiment is conducted with contacting the crossed tube specimens in air as well as in water at room temperature with various combination of contact normal force and sliding distance of reciprocating motion. The contour and the volume of each wear are examined to study the effect of contact condition and environment on wear. As a result, it is found that the wear volume in the water environment is larger than that in the air for all the contact (i.e., force and sliding distance) conditions. However, the wear depth is greater in air than in water if the contact normal force and the sliding distance are larger. These are explained by the ease of detachment of wear particles from the contact surface. On the other hand, workrate model is applied with the contact shear force range measured by our wear tester. Investigated is the correlation between the workrate and the wear volume increase rate of the present experiment. The parabolic curve is found to fit well for the present wear data.

• The Journal of Korean Academy of Prosthodontics
• /
• v.46 no.3
• /
• pp.261-268
• /
• 2008

STATEMENT OF PROBLEM: Detachment of the magnetic assembly from the denture base has been a problem in magnetic overdenture patients. PURPOSE: The objectives of this study were to compare the dislodging force by the fixing materials and the designs of the magnetic assembly, and to compare the effect between the fixing materials and the designs of the magnetic assembly. MATERIAL AND METHODS: Two fixing materials, Jet denture repair $acrylic^{(R)}$ and Super-$Bond^{(R)}$ C&$B^{(R)}$ and two types of magnetic assembly designed with or without wing were used. Each magnetic assembly was fixed in the chamber of the denture base resin block ($Lucitone^{(R)}$199) with each fixing material respectively. These specimens were thermocycled 2,000 cycles in the water held at $4^{\circ}C$ and $60^{\circ}C$ with a dwell time of 1 min each time. Each specimen was seated in a testing jig and then a push-out test was performed with a universal testing machine at a cross head speed of 0.5 mm/min to measure the maximum dislodging forces. RESULTS: Comparing the fixing materials, Super-Bond C&$B^{(R)}$ showed superior dislodging force than Jet denture repair $acrylic^{(R)}$. Comparing the design of the magnetic assemblies, the wing design magnetic assembly showed better dislodging force. Combination of the Super-Bond C&$B^{(R)}$ as a fixing material and wing design magnetic assembly revealed a greatest dislodging force. The kind of fixing material was more influential than the type of magnetic assembly. CONCLUSION: The dislodging force of Super-Bond C&$B^{(R)}$ was significantly higher than Jet denture repair $acrylic^{(R)}$. And the dislodging force of magnetic assembly which have wing design was significantly higher than magnetic assembly which have no wing design.

• Parasites, Hosts and Diseases
• /
• v.48 no.3
• /
• pp.237-243
• /
• 2010

Comprehensive quarterly serosurveillance on scrub typhus in small mammals collected from military training sites located near the Demilitarized Zone (DMZ), northern Gyeonggi-do (Province), ROK was conducted to determine the potential rodent-borne and associated ectoparasite disease risks to military personnel. A total of 1,196 rodents and insectivores representing 8 species, Apodemus agrarius (87.3%, n = 1,044), Mus musculus (5.4%, n = 65), Crocidura lasiura (3.3%, n = 40), Microtus fortis (2.6%, n = 31), Micromys minutus (0.3%, n = 4), Tscherskia triton (0.3%, n = 4), Rattus norvegicus (0.3%, n = 4), and Myodes regulus (0.3%, n = 4) were assayed for the presence of antibodies to Orientia tsutsugamushi. O. tsutsugamushi antibodies were detected in 6 of 8 species and seroprevalence determined; A. agrarius (45.6%), M. musculus (23.1%), M. fortis (48.4%), M. minutus (50.0%), T. triton (50.0%), and R. norvegicus (25.0%). A total of 31,184 chigger mites collected from 508 rodents and insectivores were slide-mounted and 10 species belonging to 4 genera were identified. Leptotrombidium pallidum (53.4%) was the most frequently collected, followed by L. pal pale (15.7%), Neotrombicula tam/yai (14.3%), L. orientate (10.7%), L. zetum (3.1%), Walchia fragilis (2.1%), and L. gemiticutum (0.8%), while the remaining 3 species, L subintennedium, N. gardellai, and Euschoengastia koreaensis were rarely observed (prevalence < 10%). In contrast to previous surveys, higher chigger indices of the primary scrub typhus vectors, L. pallidum (165.4), L. orientale (45.0), and L. palpate (21.4), were observed during the spring season.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.23 no.4
• /
• pp.403-407
• /
• 2010

Gecko adhesion system consists of beam-shaped seta and spatula which has the role of adhesive pad. In this paper, adhesion mechanism of gecko adhesion system is performed by using adhesive beam contact model. this model has a feature of non-uniform stress profile on the contact surface and adhesion/detachment mechanism is determined by the tensile stress of the contact region. a spatula tip pad has the role of reduction of maximum tensile stress and adhesive force is increased due to this effect. As for a reverse loading case, maximum compressive stress drops by the spatula effect and this cause unsymmetric loading conditions between adhesion and detachment forces. In this study, finite element method is used for the analysis of adhesive beam contact model and the results for spatula effect are presented.

• Parasites, Hosts and Diseases
• /
• v.49 no.3
• /
• pp.313-316
• /
• 2011

Vivax malaria is a significant military and civilian health threat in the north of the Republic of Korea (ROK). The island of Baengnyeong-do is the westernmost point of the ROK and is located close to the southwestern coast of the Democratic People's Republic of Korea (DPRK). Mosquitoes were collected using a black light trap on Baengnyeong-do, and Anopheles spp. were assayed by PCR, to identify the species, and screened for sporozoites of Plasmodium vivax. Of a subsample of 257 mosquitoes, Anopheles lesteri was the most frequently collected (49.8%), followed by Anopheles sinensis (22.6%), Anopheles pullus (18.7%), Anopheles kleini (7.8%), and Anopheles belenrae (1.2%). The overall sporozoite rate was 3.1%, with the highest rates observed in An. kleini (15.0%), An. sinensis (5.2%), and An. lesteri (1.6%). No sporozoite positive An. pullus or An. belenrae were observed. The results extend our knowledge of the distribution and potential role in malaria transmission of An. kleini, An. lesteri, and An. sinensis, for an area previously considered to be at a low risk for contracting vivax malaria.

• Parasites, Hosts and Diseases
• /
• v.59 no.3
• /
• pp.273-280
• /
• 2021

Biting midges (Culicoides: Ceratopogonidae) were collected using New Jersey light traps at Yongsan US Army Garrison (USAG;urban), Seoul Metropolitan city and Camp Humphreys USAG (rural), Pyeongtaek, Gyeonggi-do (province), Republic of Korea , from May-October 2010-2013 and 2015-2017, to determine species composition and seasonal distribution patterns in urban and rural habitats. A total of 9,958 female (53.85%) and 8,533 male (46.15%) Culicoides comprising 16 species were collected. Overall, the most commonly collected species was Culicoides arakawae (74.3%), followed by C. circumscriptus (16.2%), C. kibunensis (2.5%), C. nasuensis (2.2%), C. clavipalpis (1.4%), and C. pallidulus (1.3%), while the remaining 10 species accounted for <2.1% of all Culicoides spp. collected. The 2 predominant species collected were C. circumscriptus (47.4%) and C. arakawae (33.4%) at Yongsan, and C. arakawae (90.4%) and C. circumscriptus (3.9%) at Camp Humphreys. The seasonal abundance of these 2 species varied between years and between sites but on average peaked in August-September for C. arakawae and June-July for C. circumscriptus. Annual variations in abundance were observed for most species collected during this study. Unusually high proportions of male specimens were observed for most species at both sites which may be due to the use of the New Jersey trap.

• Journal of Welding and Joining
• /
• v.13 no.2
• /
• pp.115-121
• /
• 1995

As the metal transfer in the GMAW process affects the weld quality and productivity, the mechanism of molten formation and detachment has been investigated at various welding conditions. The force balance and pinch instability models have been widely used to analyze the metal transfer in the globular and spray modes, respectively A new approach is proposed in this work by minimizing the energy of molten drop system. Effects of the surface tension, gravity, electromagnetic and drag forces are considered with no presumed molten drop geometry. Effects of various welding conditions on the metal transfer are explained. The results show that the proposed mode can be applied to the globular and spray transfer modes. When compared with other models, results of the proposed model show better agreements with the available experimental data, which demonstrates the validity of the present model.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.1
• /
• pp.143-149
• /
• 2002

Robot are necessary to automate the work on a vertical plane of work piece to produce a large structure like a ship, so that a permanent magnet wheel has been attempted to be used for a mobile robot. Its adhesive power was enhanced by restricting the occurrence direction of magnetic flow. Furthermore a method which weakened the adhesive force was developed for easy detachement of the wheel by changing magnetic flow with metal pin. To measure the characteristics of the adhesive and detaching farces, a load call and a gaussmeter were used. The result showed that the adhesive power was reduced to 1/3 of normal state by using 4 inducing pins.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.103-105
• /
• 1994

A novel structure of a lineal microactuator has been designed and analyzed. The proposed structure can overcome serious problems from which conventional linear microactuators suffer, primarily due to the moving principle that is the repetition of attachment and detachment of the moving part to the fixed part. According to the calculated results, the proposed microactuator can generate force of a few mN and the moving sled of 13 cm/min under the condition of 100 volts and the frequency of 1.4 kHz.