• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.357-362
• /
• 2000

Allowable stress design(ASD) method has been widely used to design steel structures such as boiler and heat recovery steam generator(HRSG) of power plant. However, many researchers are recently intrested in road and resistance factor design(LRFD) method which may take the place of ASD. In this work, the weight calculation of steel structure was compared when ASD and LRFD were applied respectively. For the calculation of weight of steel structure, computer program was developed and applied to obtain beam weight. Using this program and GTSTRUDL, structural design program, weight of steel structure is calculated. As a result of weight calculation, maximum 5.4% of weight reduction is achieved among examples of this study by applying LRFD comparing with the result of ASD, and those results quite dependent on the applied load and member classification.

• 한국지반공학회논문집
• /
• 제23권8호
• /
• pp.107-116
• /
• 2007

하중저항계수설계법(LRFD)은 세계적으로 지반공학적 설계의 실무에서 사용이 증가하고 있으며 머지않아 현재의 허용응력설계법(ASD)을 완전히 대체할 것으로 예상된다. 하중저항계수설계법은 신뢰도해석(Reliability analysis)을 바탕으로 파괴확률을 정량화하여 상부구조물과 하부구조물을 일관된 신뢰도 수준으로 설계할 수 있게 하는 장점을 가지고 있다. 현재 암반에 근입된 현장타설말뚝의 저항계수는 단지 무결암 상태일 경우에 대하여 AASHTO에 의해 제시되어 있다. 그러나 국내의 경우, 말뚝이 근입되는 대부분의 기반암은 심하게 풍화되어 있다. 따라서 본 연구에서는 풍화암(흔히 IGM)에 대한 저항계수를 산정하고자 하였다. 이를 위해 국내 풍화암에 근입된 현장타설말뚝의 저항계수를 산정하기 위하여 신뢰도 해석을 수행하였다. 4개 현장에서 수행된 21본의 재하시험자료가 분석에 사용되었으며, 말뚝지지력을 계산하는 방법에 따라 저항계수는 $0.1{\sim}0.6$의 범위 내에서 산정되었다.

• 한국해양공학회지
• /
• 제14권2호
• /
• pp.112-116
• /
• 2000

To determine a preliminary hull form with a minimum viscous resistance this study considers the systematic variations of full form and calculations of the viscous resistance for varied hull forms. A preliminary hull form can be determined from a parametric study of viscous resistance.

• 한국지반공학회논문집
• /
• 제26권7호
• /
• pp.17-24
• /
• 2010

기초구조물의 설계에 있어 전세계적으로 하중저항계수설계법(LRFD)이 확산되는 추세이다. 현재 국내의 현장타설 말뚝 설계에 있어 AASHTO(2007)에서 제안한 저항계수를 이용하고 있지만, 이는 미국 내 분포하는 무결암에 대한 저항계수이며 지역적 가변성이 큰 저항계수의 특성상 국내 암반에 적용하기에 부적합하다. 따라서 본 연구에서는 국내에서 수행된 재하시험 자료를 이용하여 국내 지반에 적합한 저항계수를 산정하였다. 측정지지력 확인이 가능한 8개 현장의 재하시험 결과 중 22개의 자료를 이용하여 4가지의 지지력 공식에 대한 저항편향계수를 산정하였으며, 이를 이용하여 신뢰성분석을 수행하였다. 그 결과 현장타설말뚝의 안전율이 3.0일 때 목표 신뢰도지수는 약 2.01~2.30 으로 산정되었다. 또한 최적화를 이용하여 저항계수 및 하중계수를 산정한 결과 저항계수는 약 0.48~0.56, 사하 중계수는 약 1.25, 활하중 계수는 약 1.75로 산정되었다. 하지만 목표 신뢰도지수를 AASHTO에서 제안한 3.0을 이용하여 저항계수를 산정하면 목표 신뢰도지수 2.0을 적용하였을 때 산정한 저항계수의 약 50% 값을 가진다.

• 한국지반공학회논문집
• /
• 제31권10호
• /
• pp.5-16
• /
• 2015

본 연구에서는 국가건설기준이 한계상태설계법으로 전환됨에 따라 현재 연구기반이 미약한 쏘일네일링의 LRFD 설계법 개발의 일환으로 인발저항에 대한 저항편향계수를 분석하였다. 쏘일네일링의 설계 및 시공 기술수준 등 지역적 특성을 반영하기 위하여 국내 비탈면과 굴착공사에서 수행된 인발시험 자료를 수집하고, 지반특성, 쏘일네일의 제원, 인발시험 결과 등으로 구성된 데이터베이스를 구축하였다. 쏘일네일링의 인발저항에 대한 저항계수를 보정하기 위하여 국내에서 가장 많이 이용되며 비교적 자료수가 충분한 중력식과 가압식 그라우팅공법의 인발저항에 대한 저항편향계수를 산정하였다. 저항편향계수는 1.144~1.325으로 실제 극한인발저항력을 비교적 보수적으로 예측하고 있으며 미국의 연구사례(NCHRP Report)보다 안전측으로 설계가 이루어지고 있으나, 인발저항력에 대한 불확실성은 $COV_R$=0.27~0.43으로 비교적 큰 것으로 나타났다. 또한 가압식 그라우팅공법은 중력식 그라우팅공법에 비해 내재된 안전여유가 많으며, 실제 발휘되는 극한인발저항력의 불확실성이 낮은 것으로 분석되었다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 기초기술위원회 워크샵
• /
• pp.1-26
• /
• 2002

This study addresses preliminary design and construction specification for micropiles. Especially several design methods for micropiles in sands, clays or mixed soil layers are described. The bearing capacity of micropiles are mainly depended upon the shaft resistance. Therefore, the pressure of grouting is one of the most important design parameters for the bearing capacity evaluation of micropile. There is no theoretical way to evaluate the shaft resistance of micropile up to now because grouting method is another key parameter for micropile design approach. Because of above reasons, the present design approaches of the micropile are based on the collected field data The bearing capacities of designed micropiles should be verified by static load tests before and after construction at the planned site.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제10권4호
• /
• pp.499-507
• /
• 2018

Autonomous Underwater Vehicle (AUV), which are becoming more and more important in ocean exploitation tasks, needs energy conservation urgently when sailing the complex mission path in long time cruise. As hull lines optimization design becomes the key factor, which closely related with resistance, in AUV preliminary design stage, uncertainty parameters need to be considered seriously. In this research, Myring axial symmetry revolution body with parameterized expression is assumed as AUV hull lines, and its travelling resistance is obtained via modified DATCOM formula. The problems of AUV hull lines design for the minimum travelling resistance with uncertain parameters are studied. Based on reliability-based optimization design technology, Design For Six Sigma (DFSS) for high quality level is conducted, and is proved more reliability for the actual environment disturbance.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 봄 학술발표회 논문집
• /
• pp.365-372
• /
• 2002

Drilled and rock socketed piles are of increasing significance due to environmental(noise and vibration) and structural(increase of loads to carry) considerations. Drilled and rock socketed piles will therefore have much higher economic significance in the near future. The existing design of piles socketed into rock is traditionally based on empirical methods which are very unreliable. It is therefore necessary to use high factors of safety with these methods. It is appraised that this is inefficient and expensive and the potential savings from using more reliable design methods are very necessary. In this point of view, a new design approach(Seidel ＆ Collinwood, 2001) has recently been developed. This paper reviews and analyses state-of-the-art of rock socketed pile design methods for shaft resistance. On the basis of the analysis results, some recommendations for improvement of existing design method in Korea are given in this paper.

• Journal of Biosystems Engineering
• /
• 제18권4호
• /
• pp.344-350
• /
• 1993

The purpose of this study is to develop design equations to calculate optimum specifications and dimensions such as weight, engine horsepower, etc. of the tractor necessary to perform stable rotary tillage. The main results of this study are as follows. 1. A wheel-lug ought to receive a special resistance in downward direction which resists the lug's upward motion on wet sticky soil surface. The authors introduce a new academic name of the "lift resistance(上昇抵抗力, 상승저항력)" for such a force which resists retraction of a wheel lug from the soil in the upward trochoidal motion. This force is composed of the frictional force acting on the trailing and the leading lug side, and the "perpendicular adhesion(鉛直付着力, 연직부착력)" acting on the lug face and the undertread face on adhesive soil. 2. The "lift resistance ratio(上昇抵抗力係數, 상승저항력계수)" and the "perpendicular adhesion ratio(鉛直付着力係數, 연직부착력계수)" were defined, which are something similar to the definition of the motion resistance ratio, the traction coefficient, etc. 3. The design equation of the optimum weight of a rotary tiller mounted on the tractor derived by calaulating the forces acting on the rotary blades. 4. The design equations to calculate optimum specifications and dimensions such as weight, engine horsepower, etc. of the tractor necessary to perform stable rotary tillage were derived. It becomes clear that the optimum weight of a rotary tiller and a tractor can be estimated in planning design by means of putting about 21 design factors of the target into the equation. These equations are useful for planning design to estimate the optimum dimensions and specifications of a rotary tiller as well as a tractor by the use of known and/or unknown design parameters.

• 한국기계가공학회지
• /
• 제20권6호
• /
• pp.33-43
• /
• 2021

A60 class bulkhead penetration piece is a fire resistance system installed on a bulkhead compartment to protect lives and to prevent flame diffusion in a fire accident on a ship and offshore plant. This study focuses on the approximate optimization of the fire resistance design of the A60 class bulkhead penetration piece using a multi-island genetic algorithm. Transient heat transfer analysis was performed to evaluate the fire resistance design of the A60 class bulkhead penetration piece. For approximate optimization, the bulkhead penetration piece length, diameter, material type, and insulation density were considered discrete design variables; moreover, temperature, cost, and productivity were considered constraint functions. The approximate optimum design problem based on the meta-model was formulated by determining the discrete design variables by minimizing the weight of the A60 class bulkhead penetration piece subject to the constraint functions. The meta-models used for the approximate optimization were the Kriging model, response surface method, and radial basis function-based neural network. The results from the approximate optimization were compared to the actual results of the analysis to determine approximate accuracy. We conclude that the radial basis function-based neural network among the meta-models used in the approximate optimization generates the most accurate optimum design results for the fire resistance design of the A60 class bulkhead penetration piece.