• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.95-98
• /
• 2009

This paper dealt with the design guide of the conventional edge-lit backlight optic with which the on-axis luminance could be increased by trying to improve the light condensing efficiency of a bright enhancement film (BEF). First, the general design guide concerned with the backlight optic was proposed, and then its validness was experimentally proved by conducting design examples with haze controls of both diffuse film and microdot material printed on the backside of the light guide plate. Experimental results showed that the variation range of the on-axis luminance by the present approach was about $5{\sim}9%$, which would be by no means negligible in the practical application.

• Transactions of Materials Processing
• /
• v.11 no.4
• /
• pp.341-348
• /
• 2002

For the light guide plate of the TFT-LCD, there have been increasing demands for higher brightness, thin and light-weight design, and lower power consumption. To meet these demands, a micro-prism-type frontlight that integrates a prismatic sheet and a light-guiding plate has been developed. In this paper, the influences of processing conditions on the brightness were studied lot the injection molding of the light guide plate. Based on the experiment with an actual mold, the design of experiments and the neural network theory were used lot choosing the optimal processing parameters to increase the brightness and the uniformity. The verification experiment also showed that the brightness and the uniformity were increased dramatically with the chosen processing conditions.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.6
• /
• pp.53-58
• /
• 2012

A conductor has been produced according to IEC standard and low voltage electrical facility has been installed according to IEC 60364. But because of many related and varied standards, it is difficult to apply to design and inspect for electrical equipment. We researched the necessity of design guide which is detailed and systematization from survey. For detailed design guide, we suggest application method and review items at calculations for voltage drop calculations on low voltage feeder by IEC 60364, BS 7671 standard and Consumer's Electrical Installation Guide.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.19-22
• /
• 2004

A scheme of shape optimization by new approximation approach is applied to design of a flow guide in three-dimensional extrusion processes. The optimization scheme is presented to reduce computation time fur the optimization process and applied to an H-section extrusion problem for verifying the efficiency and the usefulness. The object of optimization is to minimize the deviation of exit velocity and control points of a Bezier curve describing the shape of the flow guide are regarded as design variables. The effectiveness of the proposed scheme is then demonstrated through the applied example.

• Proceedings of the Optical Society of Korea Conference
• /
• 2007.07a
• /
• pp.15-16
• /
• 2007

A design of a light coupler between a LED and a very thin light guide (0.2mm thickness) is presented. Due to the light guide's very thin thickness, conventional light couplings between LEDs and light guides do not provide enough coupling efficiency. We investigate two different coupling methods: side coupling using a complex-shaped lens and bottom coupling using a grating. This paper presents a draft design of the first approach which couples light from 0.4mm LED to 0.2mm light guide without significant losses.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.1172-1177
• /
• 2008

Diverging channel from gas burner exit to the inlet section of Heat Recovery Steam Generator (HRSG) has been re-designed for 1 MW steam supply and power generation system. Three different test geometries have been chosen for the numerical simulation. The existing design for 300 kW HRSG system (CASE B) has been improved by geometry and position changes of inlet guide vanes along with gas velocity entrance angle at the diverging channel inlet (CASE C). Both cases has been compared with the case where hot combustion gas is directly injected without any guide vanes (CASE A). Improved design shows overall uniform velocity and temperature distribution compared to existing design.

• Transactions of Materials Processing
• /
• v.11 no.4
• /
• pp.332-340
• /
• 2002

The light guide plate of the TFT-LCD reflects the light originated from the light source, and guides the light to the front side of LCD so that we can see images vividly. This paper is concerned with tile injection molding of the light guide plate for the reflective typed LCD related to IMT-2000. The finite element analysis has been carried out based on the pine stress theory to predict both the thermal stresses of the products in the post-filling stage and the in-plane deformation behavior of the products after ejection process. Based on the simulation results, the mold for the light guide plate of a 2inch sized LCD has been designed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.875-878
• /
• 2002

Braiding machines of maypole type have complex guide tracks. It is not easy to speed up drivers while carriers are moving with being at high speed. This paper presents a new design approach using dynamic analysis for moving carriers on the guide tracks. The proposed approach will be shown to be effective by using the simulation tool, WORKING MODEL 2D(equation omitted), for the high speed drivers on new models of braiding machines of maypole type.

• Journal of Science Education
• /
• v.47 no.2
• /
• pp.117-126
• /
• 2023

In an elementary school science teacher's guide, the guide in details that can help elementary school teachers with difficulties when preparing and conducting science classes are essential. To gain insights into the development of the 2022 revised curriculum elementary school science teacher's guide, it is necessary to investigate the perceptions and needs of elementary school teacher's guide in details. In this study, we developed a questionnaire by analyzing the components and design of an elementary school science teacher's guide in details to explore elementary school teachers' perceptions and needs. For this purpose, we first investigated elementary school teachers' perceptions of their needs, satisfaction, and the utilization of each component of the current guide in details. Next, we investigated teachers' needs regarding the specific components and design of a guide. The findings were as follows. First, elementary school teachers were delighted with the components that help them prepare and conduct lessons. Second, elementary school teachers wanted an easy-to-read design with a layout that allowed them to see the components they needed for their lessons at a glance. In conclusion, the elementary school science teacher's guide in details to be readable and organized to provide at-a-glance information on lesson preparation, lesson flow, and teaching and learning materials needed for science teaching-learning. Based on the results of this study, new approaches and attempts should be made to develop a textbook that elementary school teachers can utilize in the future.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.24 no.5
• /
• pp.428-432
• /
• 2012

In the waste collection system, living waste is collected through the piping network. There are many confluent pipes in a piping network. These confluent pipes were often clogged up with waste. The optimal configuration of the confluent pipes has been defined by the design guide. However, nobody know how this design guide were determined. Therefore, in this paper, we found the design data for the confluent pipe configuration in order to avoid the waste clogging in a piping network. The distance between connected point on the confluent pipes should be longer than the previous design guide.