• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.1
• /
• pp.134-145
• /
• 2021

It is common to optimize the propulsion control system through a so-called tuning process that modifies the parameter values of the propulsion control software during a ship commissioning. However, during this process, if the error of the initial setting value is large, the tuning time may take too long, or the propulsion equipment can be seriously damaged. Therefore, we conducted research on the design of a propulsion controller that applied a Processor lever controller even for inexperienced people with relatively little experience in tuning propulsion control software to be able to reduce the tuning time while protecting the propulsion system. Through simulation, by comparing the execution result of propulsion control lever commands through the PI controller without applying the Processor lever controller. We analyzed the improvement of the Overshoot and propulsion performance. The simulation results showed that the safety of the propulsion system increased because Overshoot of approximately 9.74%, which occurred when the Processor lever function was not applied.

• Applied Chemistry for Engineering
• /
• v.32 no.1
• /
• pp.61-67
• /
• 2021

In this study, the adsorption decolorization process of sea buckthorn oil was carried out to verify the possibility of the sea buckthorn oil as a natural UV absorber. The optimization was carried out by using the central composite design model-response surface methodology (CCD-RSM). The response values of CCD-RSM were selected as the decolorization effect through the process, acid value after decolorization, and UV absorbance of the decolored oil at 290nm. The amount of adsorbent, temperature and time were selected as the process variables for the experiments. According to the results of CCD-RSM, the results of optimization were all consistent. The optimal conditions, which satisfy CCD-RSM statically and mathematically, were 4.32 wt.%, 134.90 ℃, and 19.8 min for the amount of adsorbent, temperature and time, respectively. The estimated response values expected under these optimal conditions values were 94.78%, 2.08 mg/g KOH, and 2.91 for the decolorization effect, acid value and UV absorbance at 290 nm, respectively. Also the average error from actual experiment for verifying the conclusions was smaller than 2%. Therefore, it was confirmed that the application of CCD-RSM to the adsorption decolorization process of sea buckthorn oil showed a very high level of acceptable results and that the sea buckthorn oil has high possibility to be used as a natural UV absorber.

• International Journal of Computer Science & Network Security
• /
• v.22 no.3
• /
• pp.189-200
• /
• 2022

In today's digital world, smartphones and web-based applications have gained remarkable importance throughout the globe. These smart applications are playing a very significant role in maintaining a powerful business. As well as, they are helping a lot to expand these businesses via social networks. Social media networks such as Instagram, Facebook, Twitter, and LinkedIn are playing a prominent role to promote the companies. In the hospitality sector, most of the companies are running their hotel booking systems by utilizing mobile applications and a web-based infrastructure, but usability issues still exist. This study has been conducted specifically to tackle the usability issues of hotel booking systems and the best utilization of social networks to promote the business. TripAdvisor was selected as an authentic source for selecting those systems and two international hotels are selected for this study. The first step is to identify different hotel booking systems. In the second step, the user's satisfaction level was measured for the selected systems by performing the System Usability Scale (SUS, Quick & Dirty) approach. Additionally, by which source (social media or personal relations) they found these hotels. It is found that the SUS rating for both systems is below the acceptable level of usability. The Mean SUS for hotel 1 is found at 55.25 and 51.2 for hotel 2. The third step was to identify the user interface (UI) issues, and heuristic evaluation is performed for this. The experts identified the UI issues on the basis of their experience. The major issues were related to the visibility of system status, error prevention, flexibility and efficiency of use. Depending upon the identified issues, an interactive UI (prototype) for the selected web-based applications was proposed. This prototype is mainly based on the user's perspective. This prototype can be used for improving the UI of the selected systems which is based on the user's perspective. During the process of verifying the satisfaction level, it is revealed that the targeted audience is not able to use these systems efficiently and effectively. The reason behind this is the negligence of usability guidelines throughout the process of design and development of these hotel booking systems. Therefore, it is highly recommended that the usability of these systems should be evaluated and redesigned, based on expert opinions. It has also been observed that the reviews/ feedback of customers has spread a negative impact through social networks.

• Communications of Mathematical Education
• /
• v.36 no.2
• /
• pp.253-286
• /
• 2022

This study is a study in which four teachers from the same school who participated in a teacher learning community program at the school field developed interdisciplinary linkage and convergence data using Plato as a collaborative circle in ethics and mathematics subjects. In particular, this study aimed to develop practical and shareable lesson materials. The data development procedure was developed according to the following four procedures. 'Development of data development plan, data development, verification of development data, and development of final data that reflects the verification opinions' At this time, in the data development stage, a theme-based design model was applied and developed. In addition, the development data were verified by conducting CVR verification for field teachers to focus on the validity and class applicability, and the final data were presented after the development data being revised to reflect the verification results. This study not only introduced the developed data, but also described the procedure of the data development process and the trial and error and concerns of the developers in the process to provide information on the nature of basic research to other field researchers who attempt data development.

• Journal of Navigation and Port Research
• /
• v.46 no.6
• /
• pp.570-575
• /
• 2022

The MX-S2X, utilizing high-frequency broadband communication technology, provides a reliable connection between land, ship, and facilities. This technology is expected to be effectively utilized as a future maritime communication infrastructure in the upcoming mixed navigational situation among autonomous and manned and/or unmanned ships. Following the physical layer design and M&S-based performance analysis of the MX-S2X system to overcome maritime multipath fading, this paper confirms the optimized and detailed design of physical layer hardware and implemented it to verify the performance. The PER(Packet Error Rate) performance was then measured by configuring a test environment to verify the implemented hardware. The results showed that the performance degradation was 0.2 dB in the AWGN environment and 1.2 dB in the Multi-path Fading on Sea Environment, thus confirming the successful implementation of the physical layer.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.2
• /
• pp.12-19
• /
• 2022

Propellant grains with embedded metal wires have been used for enhancement of burning rate while maintaining high loading density. For the performance design of a solid rocket motor using propellant grain with embedded metal wires, burn-back analysis is required according to number, location, arrangement angle of metal wires, and augmentation ratio of the propellant burning rate near a wire region. In this study, a numerical method to quickly calculate a burning surface area was developed in response to the design change of the propellant grain with embedded metal wires. The burning surface area derived from the developed method was compared with the results of a CAD program. Error rate decreased as the radial size of the grid decreased. Analysis for characteristics of burning surface area was performed according to the number and location of metal wires, the initial and final phases were shortened and the steady-state phase was increased when the number of metal wires increased. When arranging the metal wires at different radii, the burning surface area rapidly increased in the initial phase and sharply decreased in the final phase compared to the case where the metal wires were disposed in the same radius.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.6
• /
• pp.54-63
• /
• 2022

This paper is a study on the friction damper, which is one of the seismic reinforcement devices for structures. This study developed a damper by replacing the internal friction material with ultra high molecular weight polyethylene (UHMWPE), a type of composite material. In addition, this study applied a multi-friction method in which the internal structure where frictional force is generated is laminated in several layers. To verify the performance of the developed multi-friction damper, this study performed a characteristic analysis test for the basic physical properties, wear characteristics, and disc springs of the material. As a result of the wear test, the mass reduction rate of UHMWPE was 0.003%, which showed the best performance among the friction materials based on composite materials. Regarding the disc spring, this study secured the design basic data from the finite element analysis and experimental test results. Moreover, to confirm the quality stability of the developed multi-friction damper, this study performed an seismic load test on the damping device and the friction force change according to the torque value. The quality performance test result showed a linear frictional force change according to the torque value adjustment. As a result of the seismic load test, the allowable error of the friction damper was less than 15%, which is the standard required by the design standards, so it satisfies the requirements for seismic reinforcement devices.

• Applied Chemistry for Engineering
• /
• v.34 no.2
• /
• pp.137-143
• /
• 2023

In this study, natural surfactants were extracted from Medicago sativa L. The O/W emulsification processes with the extracted natural surfactants were optimized using central composite design model-response surface methodology (CCD-RSM) and a 95% confidence interval was used to confirm the reasonableness of the optimization. Herein, independent parameters were the ratio of saponins to total surfactant (P), amount of surfactant (W), and emulsification speed (R), whereas the reaction parameters were the emulsion stability index (ESI), mean droplet size (MDS), and viscosity (V). Using the multiple reaction, the optimal conditions for the ratio of saponins to total surfactant, amount of surfactant, and emulsification speed for O/W emulsification were 49.5%, 9.1 wt%, and 6559.5 rpm, respectively. Under these optimal conditions, the expected values of ESI, MDS, and V as the reaction parameters were 89.9%, 1058.4 nm, and 1522.5 cP, respectively. The values of ESI, MDS, and V from these expected values were 88.7%, 1026.4 nm, and 1486.5 cP, respectively, and the average experimental error for validating the accuracy was about 2.3 (± 0.4)%. Therefore, it was possible to design an optimization process for evaluating the O/W emulsion process with Medicago sativa L. using CCD-RSM.

• Journal of IKEEE
• /
• v.27 no.1
• /
• pp.45-52
• /
• 2023

Cold-junction correction(CJC) and disconnection detection circuit design of various thermocouples(TC) and multi-channel TC interface circuit using them were designed. The CJC and disconnection detection circuit consists of a CJC semiconductor device, an instrumentation amplifier(IA), two resistors and a diode for disconnection detection. Based on the basic circuit, a multi-channel interface circuit was also implemented. The CJC was implemented using compensation semiconductor and IA, and disconnection detection was detected by using two resistor and a diode so that IA input voltage became -0.42V. As a result of the experiment using R-type TC, the error of the designed circuit was reduced from 0.14mV to 3㎶ after CJC in the temperature range of 0℃ to 1400℃. In addition, it was confirmed that the output voltage of IA was saturated from 88mV to -14.2V when TC was disconnected from normal. The output voltage of the designed circuit was 0V to 10V in the temperature range of 0℃ to 1400℃. The results of the 4-channel interface experiment using R-type TC were almost identical to the CJC and disconnection detection results for each channel. The implemented multi-channel interface has a feature that can be applied equally to E, J, K, T, R, and S-type TCs by changing the terminals of CJC semiconductor devices and adjusting the IA gain.

• Journal of the Korea Society of Computer and Information
• /
• v.14 no.5
• /
• pp.183-193
• /
• 2009

Both On-Line Analytical Processing (OLAF) data cubes and Statistical Databases (SDBs) deal with multidimensional data sets. and both are concerned with statistical summarizations over the dimensions of the data sets. However, there is a distinction between the two that can be made. While SDBs are usually derived from other base data, OLAF data cubes often represent directly the base data. In other word, the base data of SDBs are the macro-data, whereas the core cubiod data in OLAF data cubes are the micro-data. The base table in OLAF is used to populate the data cube with values of the measure attribute, and each record in the base tables is used to populate a cell of the core cuboid. The fact that OLAF data cubes mostly represent the micro-data may make some records be absent in the base table. Some cells of the core cuboid remain empty, if corresponding records are absent in the base table. Wang and others proposed a method for securing OLAF data cubes against privacy breaches. They assert that the proposed method does not depend on specific types of aggregation functions. In this paper, however, it is found that their assertion on aggregate functions is wrong whenever any cell of the core cuboid remains empty. The objective of this study is to design an inference control process in OLAF data cubes which rectifying Wang's error.