• Journal of the Korean Wood Science and Technology
• /
• v.33 no.2 s.130
• /
• pp.29-39
• /
• 2005

Formaldehyde emissions from wood-based panels bonded with pine and wattle tannin-based adhesives, urea-formaldehyde resin (UF), melamine-formaldehyde resin (MF), and co-polycondensed resin of urea-melamine-formaldehyde (UMF) were measured by the Japanese standard method using a desiccator (JIS A 1460) and the EN 120 (European Committee For Standardization, 1991) method using the perforator value. In formaldehyde emission, all particleboards made using the wattle tannin-based adhesive with three different hardeners, paraformaldehyde, hexamethylenetetramine, and tris(hydroxyl)nitromethan (TN), satisfied the requirements of grade $E_1$. But only those made using the pine tannin-based adhesive with the hexamine as hardener met the grade $E_1$ requirements. Hexamine was effective in reducing formaldehyde emission in tannin-based adhesives when used as the hardener. While the UF resin showed a desiccator value of $7.1mg/{\ell}$ and a perforator value of 12.1 mg/100 g, the MF resin exhibited a desiccator value of $0.6mg/{\ell}$ and a perforator value of 2.9 mg/100 g. According to the Japanese Industrial Standard and the European Standard, the formaldehyde emission level of the MDF panels made with UF resin in this study came under grade $E_2$. The formaldehyde emission level was dramatically reduced by the addition of MF resin. The desiccator and perforator methods produced proportionally equivalent results. Gas chromatography, a more sensitive and advanced method, was also used. The samples for gas chromatography were gathered during the experiment involving the perforator method. The formaldehyde contents measured by gas chromatography were directly proportional to the perforator values.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.5
• /
• pp.42-51
• /
• 2006

The this study, the effect of rice husk flour (RHF) as scavenger on formaldehyde emission rate and formaldehyde content from urea-formaldehyde (UF) resin bonded RHF content wood particleboards (PB). Two type of particle size ($30{\mu}m$ and $300{\mu}m$) of RHF was premixed with the UF resin at 5% and 15% by weight. The performance of UF resins is greatly influenced by the curing characteristics in their curing processing. The curing behavior was monitored activation energy ($E_a$) by DSC and pH variation according to RHF contents. PB with dimensions of $27cm{\times}27cm{\times}0.7cm$ was prepared at a specific gravity of 0.75 using $E_1$ and $E_2$ class UF resins. Formaldehyde emission and formaldehyde content from RHF filled PB bonded with UF resin was measured by 24 h desiccator and perforator method, respectively. RHF causes an increased pH of UF resin. $E_a$ of the modified UF resin decreased independently of RHF particle size. As the pH and the $E_a$ variation of the UF resin containing RHF increased, the amount of formaldehyde content decreased. The formaldehyde emission and formaldehyde content levels of the PB bonded with 15 wt% of $30{\mu}m$ RHF and $E_2$ type UF resin were low and satisfied grade $E_1$, as measured by 24 h desiccator and perforator method. The result of a comparison between 24 h desiccator and perforator test using PB showed that the linear regression analyses show a good correlation between the results for the 24 h desiccator and the perforator tests. The linear regression of a correlation between the desiccator and the perforator was Y=4.842X-0.064 ($R^2=0.989$). RHF was effective at reducing formaldehyde emission and formaldehyde content in urea-formaldehyde adhesives when used as scavenger.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.2
• /
• pp.129-144
• /
• 2019

This study aimed at developing an accelerated collection method that reduces measurement and collection time by improving and complementing the desiccator method, which is mainly used for quality control in wood-based panels and furniture production sites. First, this study measured the formaldehyde emissions from the wood-based panels by grade using the desiccator method. Further, this study compared the desiccator method with the developed process and analyzed the correlation in optimal temperature, time, and exposed area. The results showed that the developed process resulted in relatively similar outcomes in comparison to the desiccator method when the temperature was $100^{\circ}C$, the time was 1 h, and two specimens were used, at which the correlation was high. To verify the developed process, this study commissioned Korea Conformity Laboratories with the standardized temperature, time, and the number of specimens to compare them with the specimen that was not used in the actual test. As a result, the correlation to the desiccator method was shown to be very high. However, the formaldehyde emission measured by the accelerated collection process was mostly higher than that measured by the desiccator method. The formaldehyde emission grades from several specimens were one level higher. However, from the perspectives of quality control, it was determined that the accelerated collection method developed in this study could be sufficiently used.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.5
• /
• pp.24-37
• /
• 2007

The Korean Ministry of Environment started controlling indoor air quality (IAQ) in 2004 through the introduction of a law regulating the use of pollutant emitting building materials. The use of materials with formaldehyde emission levels above $1.25 mg/m^2{\cdot}h$ (JIS A 1901, small chamber method) has been prohibited. This level is equivalent to the $E_2$ grade ($>5.0mg/{\ell}$) of the desiccator method (JIS A 1460). However, the $20{\ell}$ small chamber method requires a 7-day test time to obtain the formaldehyde and volatile organic compound (VOC) emission results from solid building interior materials. As a approach to significantly reduce the test time, the field and laboratory emission cell (FLEC) has been proposed in Europe with a total test time less than one hour. This paper assesses the reproducibility of testing formaldehyde and TVOC emissions from wood-based composites such as medium density fiberboard (MDF), laminate flooring, and engineered flooring using three methods: desiccator, perforator and FLEC. According to the desiccator and perforator standards, the formaldehyde emission level of each flooring was ${\le}E_1$ grade. The formaldehyde emission of MDF was $3.48 mg/{\ell}$ by the desiccator method and 8.57 g/100 g by the perforator method. To determine the formaldehyde emission, the peak areas of each wood-based composite were calculated from aldehyde chromatograms obtained using the FLEC method. Formaldehyde, acetaldehyde, propionaldehyde, butyraldehyde and benzaldehyde were detected as aldehyde compounds. The experimental results indicated that MDF emitted chloroform, benzene, trichloroethylene, toluene, ethylbenzene, m,p-xy-lene, styrene, and o-xylene. MDF emitted significantly greater amounts of VOCs than the floorings did.

• The Journal of Engineering Geology
• /
• v.32 no.3
• /
• pp.401-410
• /
• 2022

This work reports an oven drying test performed on weathered granite soil from Yecheon, Korea, in order to find an effective method for measuring the weight of pure soil particles. After samples were oven dried, weights measured following desiccation using the method specified by the Korean Industrial Standard (KS F) were compared with weights measured without prior desiccation. Soil samples exposed to air for 45 min after oven drying absorbed moisture from the air and gradually increased in weight. When a desiccator was used, results measured 30 s after exposure to air indicated weight increases of 0.103-0.735% (depending on the particle size of the soil) relative to equivalent samples measured without desiccation. Using a desiccator after oven drying leads to overestimation of the pure soil weight. Therefore, measuring the weight of a soil sample immediately after oven drying without using a desiccator can reduce the error of weight measurement.

• FLOWER RESEARCH JOURNAL
• /
• v.17 no.2
• /
• pp.106-113
• /
• 2009

Germination percentage of Korean native lily seeds was high at $20-25^{\circ}C$. It was almost 100% in L. cernuum, L. callosum, L. amabile, and L. concolor, 88.0% in L. lancifolium, and 73.0% in L. maximowitzii, respectively. Meanwhile, it was low rate of 34.0%-54.0% in L. distichum, L. hansonii, and L. tsingtauense. Germination was mostly delayed of $15^{\circ}C$ and days to germination were more shortened in species with higher germination percentage. Even though the effect of daylength was not considerable in germination rate, it was promoted in L. maximowitzii but it was delyed in L. hansonii under long day. The effect of soaking in hot PGRs solution in L. callosum, L. cernuum, L. amabile, L. lancifolium, and L. concolor did not show any difference in comparison with non-treatment. However, it was improved by BA in L. maximowitzii. Longer period of cold wet storage resulted in improved germination percentage in L. maximowitzii and L. lancifolium, while it affected decreased percentage in L. distichum and L. hansonii. Days to germination were shortened by longer period of cold wet storage regardless of species. Germination percentage in dry storage was higher under cold temperature than room temperature and under desiccator storage than outside desiccator, it was highest under desiccator storage at $4^{\circ}C$. It was drastically reduced by the non-use desiccator storage at room temperature L. concolor, however it was improved only by the use of desiccator L. maximowitzii for a long time.

• Journal of the Korea Furniture Society
• /
• v.15 no.2
• /
• pp.1-17
• /
• 2004

This paper attempted to review measuring methods of formaldehyde emission from wood-based panel products. Methods included for the discussion were desiccator methods, extraction method, and various chamber methods. First, the procedures and testing conditions of 24-hour desiccator method was critically reviewed, and an improvement of this method was proposed to meet international standards. Two different small chamber methods ($20\ell$ and $1m^3$ chamber methods) were also compared in terms of their advantages and disadvantages. In addition, the regulation levels of formaldehyde emission of wood-based composite panels were compared for different countries. The selection of a reference method of measuring formaldehyde emission of wood panel products should consider the ease of conducting test and cost required. Results should be exchangeable for different methods.

• Analytical Science and Technology
• /
• v.26 no.6
• /
• pp.395-400
• /
• 2013

The hydration and antimicrobial peptide effects on the lipid alignment on the surface of a thin glass plate were investigated by using the solid-state nuclear magnetic resonance spectroscopy. Pure 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphotidylcholine (POPC) lipid molecules were well aligned on the surface of a thin glass plate without direct hydration by placing the sample for a few days in the desiccator containing a saturated sodium phosphate dibasic solution, which provided 95% relative humidity. But there was a big difference between two lipid phases, the one of which was hydrated by placing the sample for a few days in the desiccator with 95% relative humidity without direct hydration and the other was directly hydrated by dropping water and then placed for a few days in the same desiccator. The surface mobility of POPC molecules in a lipid bilayer phase was much activated by water. While the time for the POPC to align on the glass plate surface was short, the time for the PG-1/POPC mixture to reach the its equilibrium state was long.

• Journal of Pharmaceutical Investigation
• /
• v.30 no.3
• /
• pp.201-205
• /
• 2000

Three new polymorphic modifications were prepared by recrystallization under various conditions and characterized by DSC and X-ray crystallography. In pH 4.0 buffer at $37{\pm}0.5^{\circ}C$, the polymorphic modifications showed significant differences in the dissolution rate. The dissolution rate of Mod. 4, amorphous form, was faster than that of marketed cefaclor (Mod. 1). When all modifications were stored at 52% RH, 95% RH and in silica gel desiccator, any polymorphic transformation was not observed.

• Journal of Pharmaceutical Investigation
• /
• v.30 no.4
• /
• pp.289-293
• /
• 2000

Three polymorphic modifications and one amorphous form were prepared by recrystallization under various conditions and characterized by DSC and X-ray crystallography. At $37{\pm}0.5^{\circ}C$, the polymorphic modifications showed significant differences in the dissolution rate. The dissolution rate of Mod. 4, amorphous form, was faster than that of other polymorphic modifications. When all modifications were stored at 52% RH, 95% RH, and in silica gel desiccator, amorphous form was transformed at 95% humidity condition.