• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.11B
• /
• pp.967-973
• /
• 2004

DOCSIS and IEEE 802.16 define the usage and element of a MAP which is uplink control message. Standards does not include the details of MAP size and the number of contention slots affecting the performance of MAC protocols for DOCSIS and IEEE 802.16. In this paper, we analyzed the performance of throughput and access delay according to the MAP size and contention slot size. Based on the analytical results, we found the optimal MAP size and the number of contention slots. We found that the protocol shows best performance when the MAP size is 2msec and the number of contention slots is 8. The simulation results can apply to the network system parameters. The simulator can be used to optimize the system parameters in cable network, BWA and WiBro.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.3 s.357
• /
• pp.68-77
• /
• 2007

In this paper, we address TPS (Triple Play Service) based on E-PON and also develop QoS control function for both directions, which is disadvantage of E-PON. E-PON technology has the configuration suitable for TPS, but relatively the large delay characteristics in upstream, so if QoS control function must be supported to transfer the real time traffic for both directions, E-PON technology can support TPS efficiently. Therefore, in this paper, we address the diverse requirements of quality for TPS, and then develop TPS platform to verify the quality characteristics according to QoS characteristics of each element in real environment based on this. This result will be used to improve the quality of TPS that become conventional in near future. ISP will use this result as the basis in establishing quality reference and as the guidance in developing new system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.2 s.93
• /
• pp.154-160
• /
• 2005

Microwave Otters are essential device in modem wireless systems. A compact dimension BPF(Band-pass Filter) for IEEE 802.11a WLAN service is realized using LTCC multi-layer process. To extrude 2-stage band-pass equivalent circuit, band-pass and J-inverter transform applied to Chebyshev low-pass prototype filter. Because parallel L-C resonator is complicate and hard to control the inductor characteristics in high frequency, the shorted $\lambda/4$ stripline is selected for the resonator structure. The passive element is located in the different layers connected by conventional via structure and isolated by inner GND. The dimension of fabricated stacked band-pass filter which is composed of six layers, is $2.51\times2.27\times1.02\;mm^3$. The measured filter characteristics show the insertion loss of -2.25 dB, half-power bandwidth of 220 MHz, attenuation at 5.7 GHz of -32.25 dB and group delay of 0.9 ns at 5.25 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.5
• /
• pp.416-423
• /
• 2016

In this paper, a conformal type $1{\times}4$ microstrip patch array antenna with tilted antenna beam is presented for UWB sensor applications. Each antenna element comprises E-shaped patch with L-probe feeding to increase the bandwidth. The tilted antenna beam of 20 degree can be achieved with 42 ps microstrip delay lines at the series feeding network with T-junctions. The measured reflection coefficient is >9 dB at 3.5~4.5 GHz. The measured antenna gain and HPBW are >10 dBi and <30 degree at 3.75~4.25 GHz.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2004.09a
• /
• pp.138-141
• /
• 2004

The environmental tracers tritium/helium-3 (3H/3He) and chlorofluorocarbons (CFCs) were investigated in ground water from Jeju Island, Korea, a basaltic volcanic island. The apparent 3H/3He and CFC-12 ages were in relatively good agreement in samples with low concentrations of terrigenic He. Ground water mixing was evaluated by comparing 3H and CFC-12 concentrations with mixing models, which distinguished old water with negligible 3H and CFC-12, young water with piston flow, and binary mixtures of the two end members. The ground water CFC-12 age is much older in water from wells completed in confined zones of the hydro-volcanic Seoguipo formation in coastal areas than in water from the basaltic aquifer. Comparison of major element concentrations in ground water with the CFC-12 age shows that nitrate contamination processes contribute more solutes in young water than are derived from water-rock interactions in non-contaminated old water. Chemical evolution of ground water resulting from silicate weathering in basaltic rocks reaches the zeolite-smectite phase boundary. The calcite saturation state of ground water increased with the CFC-12 apparent (piston flow) age. In agricultural areas, the temporal trend of nitrate concentration in ground water was consistent with the known history of chemical fertilizer use on Jeju Island, but the response of nitrate concentration in ground water to nitrogen inputs follows an approximate 10-year delay. Based on mass balance calculations, it was estimated that about 40% of the nitrogen applied by fertilizers reached the water table and contaminated ground water resources when the fertilizer use was at the highest level.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.5
• /
• pp.941-950
• /
• 2001

In this paper, we present the integrated network architecture for supporting mobile IP in third generation mobile communication networks, and propose the end-to-end QoS control mechanisms of DiffServ and QoS control functions of each network element in the proposed network. First, the QoS supporting schemes of IMT-2000 are described. Second, the necessities of integrating the networks are discussed and the integrated architecture are proposed. Third, the mapping between wireless channels and DiffServ classes are presented. Finally, the end-to-end QoS control mechanisms are proposed. We also analyze the link level protocols with QoS provisioning for mobile multimedia assuming that the system support voice and data traffic simultaneously. In case of data traffic, the delay and throughput of SREJ ARQ and Type-1 Hybrid ARQ scheme are compared, and In case of voice traffic, the packet loss rate of BCH coding is analyzed according to the varying data traffic loads. The results indicate that the adaptive link level protocols are efficient to meet the QoS requirements while the complexities are increased.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.5 no.4
• /
• pp.335-342
• /
• 2000

A new control method for a single-phase active power filter, based on a load current estimation using a DC capacitor voltage of active power filter without sensing nonlinear load current, is proposed in this paper. Because the method proposed can remove the load current sensor in comparison with a conventional method sensing the load current and DC capacitor voltage together, it can make the active power filter easy installation, low cost, small size with no performance detriment. In addition, sample-hold technique and proportional control method is adopted to control the DC capacitor voltage and as no delay element such as LPF or PI control in the conventional method is used, the transient response is fast and good. Operation of a single-phase active power filter which consist of eight mode is explained according to utility voltage, compensation current and switch state, and compensation characteristics of active power filter using proposed method is verified by experiment.

• Proceedings of the KSRS Conference
• /
• 2007.10a
• /
• pp.540-543
• /
• 2007

The modulation transfer function (MTF) in a camera system is a measurement of how well the system will faithfully reproduce the original scene. The electro-optical camera system consists of optics, an array of pixels, and an electronics which is related to the image signal chain. The system MTF can be cascaded with each element's MTF in the frequency domain. That is to say, the electronics MTF including the detector MTF can be recalculated easily by the acquired system MTF if the well-known test optics is used in the measuring process. A Time-Delay and Integration (TDI) detector can make a signal increase by taking multiple exposures of the same object and adding them. It can be considered the various methods to measure the MTF of the TDI camera system. This paper shows the actual and practical MTF measuring methods for the detector and electronics in the TDI camera. The several methods are described according to the scan direction as well as the TDI stages such as the single line mode and the multiple-lines mode. The measuring is performed in the in the static condition or dynamic condition to get the point spread function (PSF) or the line spread function (LSF). Especially, the dynamic test bench is used to simulate on track velocity to synchronize with TDI read out frequency for the dynamic movement.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.26 no.1
• /
• pp.88-100
• /
• 1990

Since sea state changes engine load instantaneously, the speed governing apparatus is essential for marine engine to maintain constant speed regardless of the load. As governing apparatuses, mechanical, pneumatic, and electric governors have been employed. But, recently, according to the introduction of low speed-ling stroke engines to increase thermal efficiency, the development of governor which has better response characteristics is requisite. In this paper, to design the governor that meets above requirement, author made a performance test for the existing PID control digital governor with the aid of computer simulation, and investigated digital governor applying the optimal control algorithm, then, executed computer simulation by the same way. As the result of simulations, found that the former let engine have large overshoot and long settling time at low speed, on the other hand, the latter made engine have better response. If we design and invent a good observer for delay time element so that the optimal control theory can be applied, better governor will be expected.

• Journal of Sensor Science and Technology
• /
• v.15 no.1
• /
• pp.34-39
• /
• 2006

This study provides the electrical model of combustible catalytic gas sensor. Physical characteristics such as thermal behavior, resistance change were included in this model. The finite element method analysis for sensor device structure showed that the thermal behavior of sensor is expressed in a simple electrical equivalent circuit that consists of a resistor, a capacitor and a current source. This thermal equivalent circuit interfaces with real electrical circuit using two parts. One is 'power to heat' converter. The other is temperature dependent variable resistor. These parts realized with the analog behavior devices of the SPICE library. The gas response tendency was represented from the mass transferring limitation theory and the combustion theory. In this model, Gas concentration that is expressed in voltage at the model, is converted to heat and is flowed to the thermal equivalent circuit. This model is tested in several circuit simulations. The resistance change of device, the delay time due to thermal capacity, the gas responses output voltage that are calculated from SPICE simulations correspond well to real results from measuring in electrical circuits. Also good simulation result can be produced in the more complicated circuit that includes amplifier, bios circiut, buffer part.