• 열처리공학회지
• /
• 제10권3호
• /
• pp.198-208
• /
• 1997

The-steady-state creep mechanism and behavior of Zircaloy-4 used as cladding materials in PWR have been investigated in air environment over the temp, ranges from 600 to $645^{\circ}C$ and stress ranges from 4 to $7kg/mm^2$. The stress exponents for the creep deformation of this alloy, n were decreased 4.81, 4.71, 4.64, and 4.56 at 600, 615, 630 and $645^{\circ}C$, respectively; the stress exponents decreased with increasing the temperature and got closer to about 5. The apparent activation energies, Q, were 62.1, 60.0, 57.9 and 55.4 kcal/mole at stresses of 4, 5, 6, $7kg/mm^2$, respectively; the activation energies decreased with increasing the stress and were close to those of volume self diffusion of Zr in Zr-Sn-Fe-Cr system. In results, it can be considered that the creep deformation for Zircaloy-4 was controlled by the dislocation climb over the ranges of this experimental conditions. Larson-Miller parameter, P, for the crept specimens was obtained as P=(T+460)(logt,+23). The failure plane observed by SEM slightly showed up intergranular fracture at this experiment ranges. However, it was essentially dominated by the dimple phenomenon, which was a characteristics of the transgranular fracture.

• 한국지반공학회논문집
• /
• 제30권2호
• /
• pp.33-42
• /
• 2014

매우 낮은 구속응력에서의 모래의 전단강도 및 변형특성은 상대적으로 높은 구속응력의 경우와 매우 상이한 분포를 나타낸다. 따라서 낮은 응력상태를 보이는 지반 위에 놓인 얕은 기초와 제방 등의 안정성, 토석류 혹은 얕은 파괴의 안정성 검토와 실내에서 시행하는 각종 모델시험의 경우 이에 대하여 명확히 규명할 필요가 있다. 본 연구에서는 건조된 주문진 표준사를 대상으로 구속응력을 5kPa~300kPa로 하여 배수 삼축시험을 실시하였으며, 그 결과 내부마찰각(${\phi}$) 및 변형계수($E_s$)가 구속응력(${\sigma}{_c}^{\prime}$)에 따라 크게 변하는 것을 확인하였으며, 이에 따라 구속응력에 대한 조밀 및 느슨한 모래의 내부마찰각과 변형계수의 상관관계식을 제안하였다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제34회 추계학술대회 개최
• /
• pp.69-77
• /
• 2001

Wear and Friction characteristics of plasma-sprayed Cr$_2$O$_3$ coating and Cr$_2$O$_3$ coating included SiO$_2$ and TiO$_2$ against SiC ball have been investigated under different loads. Worn surfaces were observed by SEM and worn surfaces were analyzed by EDS. The Friction coefficient and the Wear resistance of Cr$_2$O$_3$-5SiO$_2$-3TiO$_2$coating was less than that of Cr$_2$O$_3$ coating. The main mechanisms were plastic deformation and brittle fracture. The film on surface were made by plastic deformation and compacted wear debris. This film protect wear of coating

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2001년도 유체기계 연구개발 발표회 논문집
• /
• pp.482-487
• /
• 2001

Leaf type foil bearings have been used successfully in many aerospace applications such as air cycle machines, turbocompressors and turboexpander. These applications are characterized by light loads, constant speeds and low to moderate temperatures. But, as system on start-up or shutdown, sliding contact between the shaft and foil surfaces cause wear. So, in present study, to understand pressure-flow characteristics and deformation of foil bearing, flow/structure interaction analysis was used. and using this method, 2D and 3D calculation was peformed for shape of foil bearing to know circumferential direction flow and leakage flow characteristics of axial direction.

• 한국도로학회논문집
• /
• 제4권4호
• /
• pp.23-39
• /
• 2002

본 논문은 아스팔트 포장의 소성변형 저항성 추정을 보다 쉽게 하기 위하여 새로운 시험법 및 장비를 개발하기 위한 연구이다. 본 연구에서는 다양한 종류의 아스팔트 혼합물을 사용하여 소성변형 저항성과의 상관성이 높게 나타나는 변형강도를 개발하기 위하여 하중봉의 직경(D) 3, 4cm, 각 봉의 하단을 다양하게 원형절삭(r)한 김 테스터를 개발하였다. 이를 이용하여 마샬시험과 같이 공시체를 $60^{\circ}C$에 수침처리하고 같은 속도의 정하중을 공시체에 다짐방향으로 가하여 최대하중 ($P_{max}$)과 이때의 수직 변위 (y)를 구하였다. 변형강도는 개발된 식 $K_D = 4P_{max}/{\pi}(D-2(r-\sqrt{2ry-y^2}))^2$으로 구하였으며 소성변형 특성치와 평균 $R^2$이 0.77이상의 높은 상관성을 보였다. 따라서 이 시험방법은 마샬안정도보다 훨씬 소성변형과의 상관관계가 큰 측정치를 얻을 수 있는 방법임을 알 수 있었으며, 특히 기존의 마샬시험기를 그대로 사용하고 공시체도 기존의 방법대로 제조 및 처리하도록 하여 적용이 빠를 것으로 판단된다. 향후 다양한 골재입도, 최대치수, r 등에서도 타당성과 상관성 검증을 통해 시험법을 표준화한다면 실용화 가능성이 매우 클 것이다.

• 한국자동차공학회논문집
• /
• 제14권1호
• /
• pp.79-85
• /
• 2006

CFRP(Carbon Fiber Reinforced Plastics) of the advanced composite materials as structural materials for vehicle, has a wide application in light-weigh structural materials of airplanes, ships and automobiles because of high strength and stiffness, However, there is a design variable to be considered in practical application of the laminate composite materials, these materials are vulnerable to transverse impact. This paper is to study the effects of stacking sequence and curvature on the penetration characteristics of composite laminate shell. They are stacked to $[0_3/90_3]S,\;[90_3/0_3]s\;and\;[0_2/90_3/0]s,\;[90_2/0_3/90]s$ and their interlaminar number two and four. They are manufactured to various curvature radius (R=100, 150, 200mm and $\infty$), When the specimen is subjected to transverse impact by a steel ball, the velocity of the steel ball was measured both before and after impact by determing the time for it to pass two ballistics-screen sensors located a known distance apart. The critical penetration energy of specimen A and B with less interfaces were a little higher than those of C and D. As the curvature increases, the critical penetration energy increases linearly because the resistance to the in-plane deformation as well as bending deformation increases, which need higher critical penetration energy. The specimen A and C have higher critical penetration energy than B and D because of different stacking sequences. We examined crack length through a penetration test. For the specimen A with 2interfaces, the longest circumferential direction crack length were observed on the first interface from the impact point. For the specimen B 4-interface, the longest circumferential direction crack length were observed on the second interface from the impact point.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.284-284
• /
• 2011

Recently, the increasing degree of device integration in the fabrication of Si semiconductor devices, etching processes of nano-scale materials and high aspect-ratio (HAR) structures become more important. Due to this reason, etch selectivity control during etching of HAR contact holes and trenches is very important. In this study, The etch selectivity and etch rate of TEOS oxide layer using ACL (amorphous carbon layer) mask are investigated various process parameters in CH2F2/C4F8/O2/Ar plasma during etching TEOS oxide layer using ArF/BARC/SiOx/ACL multilevel resist (MLR) structures. The deformation and etch characteristics of TEOS oxide layer using ACL hard mask was investigated in a dual-frequency superimposed capacitively coupled plasma (DFS-CCP) etcher by different fHF/ fLF combinations by varying the CH2F2/ C4F8 gas flow ratio plasmas. The etch characteristics were measured by on scanning electron microscopy (SEM) And X-ray photoelectron spectroscopy (XPS) analyses and Fourier transform infrared spectroscopy (FT-IR). A process window for very high selective etching of TEOS oxide using ACL mask could be determined by controlling the process parameters and in turn degree of polymerization. Mechanisms for high etch selectivity will discussed in detail.

• Journal of Welding and Joining
• /
• 제17권1호
• /
• pp.97-103
• /
• 1999

Ships, structures on the ocean, bridges, and other structures tend to be large by the development of industry. These ultra thick plate were welded with large heat input, which causes welding stresses, deformation and buckling, so it has to be considered the weld design, safety, reliability. The welded residual stresses were produced and redistributed due to the effect of large heat input. The mechanical phenomenon has not been surely identified yet. In spite of the lack of the study on the box column, there are various types of steel frame such as I type, H type, + type and $\bigcirc$ type, used in high story building. In this study, we performed computer simulation with two dimensional heat conduction and plane deformation thermal elasto-plastic finite element computer program as changing the plate thickness to 100mm, 150mm and groove angle to $60^{\circ}C$, $45^{\circ}C$, $30^{\circ}C$ of corner joint in box column. And then, to identify mechanical phenomenon such as the phenomenon of thermal distribution, welding residual stresses and deformation and to decide optimum groove angle and welding condition. The main conclusion can be summarized as follows: 1) Since the groove angle has became cooling down rapidly due to its smaller value, the temperature slope was steeped somewhat. 2) The tensile stress within the welding direction stresses was somewhat decreased at the weld metal and HAZ, increasing of the groove angle. 3) The local stress concentration of the groove angle $60^{\circ}C$ was appeared smaller than groove angle $30^{\circ}$.

• 암석학회지
• /
• 제23권2호
• /
• pp.61-73
• /
• 2014

소백산육괴의 중앙부에 위치하는 경상북도 북후면-평은면 지역에서 주 구성암류인 선캠브리아기 변성퇴적암류와 중생대 화강암에 대한 변형된 암석 및 미구조 연구를 통하여 (동)북동-(서)남서 방향으로 발달하는 우수 주향 이동성 예천전단대의 상대적인 형성시기, 변형온도, 초압쇄암대의 분포 등을 파악하였다. 연성 변형된 주요 암석구조는 전단변형에 의해 형성된 압쇄구조면과 신장선구조 그리고 편마구조면 내지 압쇄구조면이 습곡되어 형성된 (동)남동-버전스의 완침강-중경사 밀착습곡 등이 있다. 연성전단변형 동안에 형성된 장석들의 특징적인 미구조는 플레임 퍼어사이트, 밀메카이트, 미세단열, 미세킹크, 킹크대, 파동소광 등이 인지된다. 재결정된 석영집합체의 c-축 배열은 rhomb와 basal가 탁월한 미끄럼계로 작용하여 형성된 single girdle과 Type I crossed girdle 형태를 보여준다. 전단운동감각 결정면상에서 인지되는 전단운동감각은 우세한 방향성인 북서-경사와 부수적인 방향성인 남동-경사 압쇄구조면상에서 상부-북동-이동과 상부-남서-이동을 각각 보여준다. 이러한 특징적인 암석 및 미구조로부터 예천전단운동은 밀착습곡이 형성된 이후 발생하였으며, 예천전단운동이 발생할 당시의 변형온도는 $350{\sim}450^{\circ}C$이었음을 알 수 있다. 선캠브리아기 변성퇴적암류의 대상 분포와 변형된 선캠브리아기 변성퇴적암류의 장석과 중생대 화강암의 석영의 입도 분포로부터 불노봉과 박달산 북부를 통과하는 (동)북동 방향의 예천전단대의 초압쇄암대가 설정된다.

• 한국주조공학회지
• /
• 제28권1호
• /
• pp.31-36
• /
• 2008

Ti-Ni-Cu alloys are very attractive shape memory alloys for applications as actuators because of a large transformation elongation and a small transformation hysteresis. Rapidly solidified Ti-Ni alloy ribbons have been known to have the shape memory effect and superelasticity superior to the alloy ingots fabricated by conventional casting. In this study, solidification structures and shape memory characteristics of $Ti-Ni_{30}-Cu_{20}$ alloy ribbons prepared by melt spinning were investigated by means of DSC and XRD. Operating parameters to fabricate the amorphous ribbons were the wheel velocity of 55 m/s and the melt spinning temperature of $1500^{\circ}C$. The crystallization temperature was measured to be $440^{\circ}C$. The crystallized ribbons exhibited very fine microstructure after annealing at $440^{\circ}C$ for 10 minutes and $460^{\circ}C$ for 5 minutes and was deformed up to about 6.8% and 6.23% in ductile manner, respectively. Stress-strain curve of the ribbon exhibited a flat stress-plateau at 64 MPa and this is associated with the stress-induced a B2-B19 martensitic transformation. During cycle deformation with the applied stress of 220 MPa, transformation hysteresis and elongation associated with the B2-B19 transformation were observed to be $4.3^{\circ}C$ and 3.6%.