• Computers and Concrete
• /
• v.11 no.1
• /
• pp.63-73
• /
• 2013

In this study, the effect of reducing cement by proportional addition of waste powder rubber on the performance of concrete under impact three-point bending loading were investigated experimentally and numerically. Concrete specimens were prepared by adding 5%, 10% and 20 % of rubber powder as filler to the mix and decreasing the same percentage of cement. For each case, three beams of $50mm{\times}100mm{\times}500mm$ were loaded to failure in a drop-weight impact machine by subjecting them to 20 N weight from 300mm height, while another three similar beams were tested under static load. The bending load-displacement behavior was analyzed for the plain and rubberized specimens, under static and impact loads. A three dimensional finite-element method simulation was also performed by using LUSAS V.14 in order to study the impact load-displacement behavior, and the predictions were validated with the experimental results. It was observed that, despite decreasing the cement content, the proportional addition of powder rubber until 10% could yield enhancements in impact tup, inertial load and bending load.

• Journal of the East Asian Society of Dietary Life
• /
• v.20 no.1
• /
• pp.122-127
• /
• 2010

This study involved the making of sugar snap cookies with the addition of carrot powder at two to twelve percent which furnishes modern people with much lacking and needed dietary fiber. The review of the physiochemical properties, rheology and sensory evaluation of such contents resulted in the following findings: The sedimentation value and Pelshenke value all decreased in weak flour with the addition of more carrot powder, in comparison with the control group. The water retention capacity (WRC) and alkaline water retention capacity (AWRC) all increased in weak flour with the addition of more carrot powder in comparison with the control group. As for the gelatinization properties of the test samples measured by rapid visco-analysis, the addition of more carrot powder resulted in the initial pasting temperatures increasing in the case of weak flour, yet showing no significant difference between the control group and the carrot-added groups, as well as the maximum viscosity, minimum viscosity and final viscosity all showed the tendency of decreasing. The addition of more carrot powder led to the peak times in the mixographs for weak flour all exhibiting the tendency of decreasing, which might be interpreted as gradually weaker physical properties of the dough as well as less stability in the shape of the dough in turn.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.7
• /
• pp.387-398
• /
• 2002

In this paper, a new Three-Phase Lead-Lag Random Pulse Position PWM(LL-RPWM) scheme is proposed and implemented for decreasing audible acoustic noise of motor drives. In the proposed RPWM(Random PWM), each of three phase pulses is located randomly in each switching interval. Based on the space vector modulation technique, the duty ratio of the pulses is calculated. Along with the randomization of the PWM pulses, we can obtain the effects of spread spectra of voltage, current as in the case of randomly changed switching frequency. To verify the validity of the proposed LL-RPWM, the simulation and experimental study was tried. Along with the randomization PWM pulses, the space vector modulation is also executed in the C167 micro-controller. The simulation and experimental results show that the voltage and current harmonics are spread to a wide band area and that the audible acoustic noise is reduced by the proposed RPWM method.

• Proceedings of the KIEE Conference
• /
• 2002.07a
• /
• pp.79-82
• /
• 2002

The addition of switches to a distribution feeder does, in general, increase reliability by decreasing the duration of the outage of many to the customers on the feeder. To cover its service area so that feeder-level delivery reaches sufficiently close to all customers, feeders typically split their routes many times, in what is often called a lateral feeder. It is interesting to note, however, that the effectiveness of a switch is very much dependent on the types of lateral feeder. The types of lateral are classified into two types. The first is loop lateral feeder that can connect its load to an adjacent feeder through a tie line in case that a fault occurs in its feeder and it is laid out so that every feeder has complete fault backup through re-switching of its loads to other sources like a main feeder. The second is the radial lateral feeder cannot connect its load to an adjacent line, no provision is made for contingency backup of feeders. There are no other circuits in the radial lateral feeder form which to restore power. In this study, we evaluate the effectiveness of a switch installation between on the radial and loop lateral feeders to increase reliability by decreasing the duration of the outage. These results can help power utility to design the switch layouts on the radial and loop lateral feeder system.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.8
• /
• pp.64-72
• /
• 2020

In this study, a stability analysis was conducted through finite element analysis (FEA) of a simplified model of a fire ladder truck by changing the ascending angle, turning angle, and boundary conditions between the outrigger and the ground. The results of the analysis showed that decreasing the angle of the ladder car increases the moment due to the ladder weight, decreasing the safety factor despite being under the same load conditions. In the case of a rotating radius, the stability was found to vary depending on the boundary conditions. A comparative analysis in the future with these results and the experimental values from the actual fire ladder truck may determine the most appropriate boundary conditions based on the analysis program. It is expected to predict the risk of damage and rollover by assessing the stability of aerial ladder vehicles under different conditions.

• Journal of the Korean Society for Heat Treatment
• /
• v.15 no.6
• /
• pp.255-259
• /
• 2002

Effect of martensite on the mechanical properties of austempered ductile cast iron was investigated after obtained the martensite by subzero treatment. Retained austenite was transformed to martensite by subzero treatment, and with decreasing subzero treatment temperature, volume fraction of martensite was increased. With increasing of the volume fraction of martensite, tensile strength was increased and elongation was decreased, ratio of increasing of strength and decreasing of elongation was higher in case of specimens with lot's of Cu contents. With increasing of the volume fraction of martensite, hardness slowly increased until only about 5% and it rapidly increased in a straight proportion when it is above 5%, while impact value was rapidly decreased until about 7% but it had a little change when it is above 7%.

• Journal of Korean Academy of Nursing
• /
• v.30 no.2
• /
• pp.282-292
• /
• 2000

A meta-analysis of 14 quasi-experimental studies was conducted to compare the effect of size on various relaxation therapies applied to patients and health volunteer students. These studies were selected from theses, dissertations and papers that have been done between 1982 to 1993. Also They have a randomized or nonequivalent control group in a pre test-post test design. The studies were evaluated in different ways; 1) types of relaxation therapy, 2) total amount of time of relaxation therapy, and 3) types of outcome variables. For a group of homogenious studies, the weighted mean effect size and standard error were estimated. Some findings are summarized as follows : 1. Jacobson relaxation therapy had a larger effect on systolic and diastolic blood pressures than on state anxiety. 2. For the total time of relaxation therapy, (longer than 60 minutes) had a much larger effect in decreasing systolic and diastolic blood pressures than in the case of a time period shorter than 60 minutes. 3. Relaxation therapy applied to surgery patients also had a larger effect in decreasing state anxiety than when applied to other patients.

• Asia pacific journal of information systems
• /
• v.13 no.1
• /
• pp.73-101
• /
• 2003

Firms can create additional customer values by changing the visibility characteristic of business transactions. Both visible and invisible transactions can provide distinctive values to the customers. Visible transactions are those that are open to the customer: the customer can see the detailed logic of the transaction and may manipulate specific variables to control the transaction process. Invisible transactions mean that customers have little ability to control the transaction flow and may even be insulated from seeing the transaction. These invisible transactions will be taken care of only by suppliers, and be regarded as a process performed by suppliers. This paper pursues finding out the contingencies of successful transaction visibility change by answering to the following question; "when does increasing(or decreasing) transaction visibility make sense to customers?" This archival case study finds out that transaction visibility change should fit to the need and capabilities of customers. Increasing transaction visibility makes sense when customers need a certain supplier's performance and have a confidence in the capabilities of executing the performance. By the same token, decreasing transaction visibility makes sense when customers have substantial troubles in conducting their current transaction actions or when customers don't feel it necessary to conduct them separately because they can be derived from other action.

• Journal of the Korean Society for Heat Treatment
• /
• v.11 no.1
• /
• pp.46-53
• /
• 1998

The variation of the mechanical properties, microstructures and the formation of retained austenite with heat treatment conditions in austempered ductile cast iron has been investigated. In the case of austempered ductile cast iron below 25mm diameter, it has been found that a pearlite structure are not obtained under a super cooled condition at range of $0.05^{\circ}C/sec{\sim}10^{\circ}C/sec$, and the matrix is precipitated in graphite, bainite and retained austenite. After austempering treatment the retained austenite is increased with decreasing cooling rate. The elongation increases with decreasing super cooling rate, and the optimum result has been shown to be the elongation of 15.6% at super cooling rate of $0.05^{\circ}C/sec$. The optimum result has been shown to be the tensile strength-elongation balance of $1656kgf/mm^2.%$ and it is more than doubled to as the casting state and continuous cooling condition.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.3
• /
• pp.120-126
• /
• 2005

The method of decreasing the ecological risk for the LRE(Liquid Rocket Engine) test is developed, working on the cryogenic oxidizer and the high-boiling fuel(Kerosene). This Method is based on the study that contains a technical solution method and an accident occurrence range for decreasing of accident probability and damage. This paper contains schematic on the all risk circumstance bring to accident, block-diagram for an accident growth process in case of the propellant leakage, technical solution method and risk reduction evaluation method. It will be used to alternative method for the risk reduction of complex technical systems.