• Journal of the Korean Wood Science and Technology
• /
• 제34권3호
• /
• pp.22-29
• /
• 2006

친환경 건축자재에 대한 관심이 높아짐에 따라서 가구 및 건축 내외장재로 사용되는 목질복합재료에 대한 친환경적 성능에 대한 요구는 점차 커져가는 추세이다. 목질 복합재료는 일반적으로 그 자체로 사용하기 보다는 표면재를 붙여서 사용하는데 이때 사용되는 요소포름알데히드 접착제를 친환경적인 SIS계 핫벨트 점착제로 대체코자 하는 데 이 연구의 목적이 있다. 본 연구에서는 기질고분자의 diblock 함량, 점착부여수지의 연화점 및 함량 등을 변화시키면서 여러 종류의 핫벨트 점착제를 제조하고 각각의 점착제에 의한 무늬목 부착성능을 평가함으로써 점착형 표면재에 대한 가능성을 제기하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제25권4호
• /
• pp.22-28
• /
• 1997

This research was carried out to obtain the fundamental data for the development of the technology and practical use of far-infrared radiation(IR) drying of quarter-sliced decorative veneers of walnut and red oak. The average drying rates of IR drying were about one and half to four times those of kiln drying and this tendency was prominent in thin veneer. The end wavinesses of the IR-dried veneers were smaller than those of kiln-dried veneers. These were largely recovered by the cold treatments after drying. The consumed electric power for IR drying was about one-fifth to two-fifthes compared to that for kiln drying.

• 한국가구학회지
• /
• 제11권1호
• /
• pp.61-68
• /
• 2000

This study was carried out to investigate the effect of grain and veneer thickness on drying rate, required energy consumption, and drying defects such as checking, end waving, and burning during a far-infrared radiation drying process of decorative veneers of hard maple and beech. Most of the veneer could be dried from green to in-use moisture content within 30 to 360 seconds. The drying rates were significantly affected by veneer thickness, but there was little difference between edge-and flat-sliced veneers. The formation of checking during drying test was none or very slight. The percentages of the veneers defected by checks were higher in the flat-sliced veneers than in the edge-sliced veneers. The maximum end wavinesses in the flat-sliced veneers were almost 1.6 to 3 times larger than that in the edge-sliced veneers. All veneers were fee from burned marks during drying test.

• 한국가구학회지
• /
• 제10권2호
• /
• pp.29-36
• /
• 1999

During a radio-frequency/vacuum plus press drying process of some hardwood veneers for decoration we investigated the effect of a grain and thickness of a veneer sheet on drying rates, variations of final moisture content within a bundle of veneer sheets, and formation of checking, end waving, and burning mark. About thirty three hundreds sheet of veneer could be dried in sixty five hours from green to in0-use moisture content, and a final moisture content was significantly effected by initial moisture content of veneer. There were nearly variations in a final moisture content among the veneer sheets in the same bundle. A checking was never found in a edge-sliced veneer, and very slight in a flat-sliced veneer of ash and red oak. There were no end waving and no burning mark in all veneer sheets.

• Journal of the Korean Wood Science and Technology
• /
• 제36권2호
• /
• pp.39-45
• /
• 2008

Formaldehyde and volatile organic compounds (VOCs) are emitted from wood-based panels that have been made using wood particles, wood fiber, wood chips, formaldehyde-based resins and so on. In this study, we examined formaldehyde and total VOCs (TVOC) emission behaviors for plywood overlaid with water-soluble phenolic resin impregnated linerboard (PL), and two kinds of surface materials (decorative veneer and pre-impregnated finishing foil) that were adhered onto the PL that named DPL and PPL. EVA (ethyl vinyl acetate) was used to overlay the decorative veneer and pre-impregnated finishing foil on the plywood with water-soluble phenolic resin impregnated linerboard by a hot press instrument. The debonding test and accelerated aging test were conducted to assess their mechanical properties. Formaldehyde and TVOC emission concentrations were measured using the FLEC method and a VOC Analyzer, respectively. The debonding test results of PL, DPL and PPL were 1.2, 1.5, and $0.5N/mm^2$, respectively. The surface appearance of the samples were not changed after the accelerated aging test. The PL and DPL exhibited reduced formaldehyde and TVOC emission levels, respectively. In the case of PPL, the VOC value was relatively higher than those of PL and DPL.