• 한국추진공학회지
• /
• 제24권6호
• /
• pp.126-142
• /
• 2020

본 연구에서 액체-액체 핀틀 분사기가 적용된 연소장치의 연구개발 사례 조사를 통해 핀틀 분사기 및 연소장치의 설계 기초자료를 제공하고자 하였다. 자료 분석 결과로 엔진 추력에 따른 연소실 및 핀틀 분사기 규격, 고효율 분사기의 형상을 확인할 수 있었다. 그밖에 핀틀팁 열손상 방지 기구와 소재, Face-shutoff 핀틀 분사기 구현 방법, 중심추진제 선정 기준 등을 정리하여 초기 핀틀 분사기 적용 연소실 설계의 기초자료로 활용하고자 한다.

• Journal of Mechanical Science and Technology
• /
• 제20권6호
• /
• pp.896-904
• /
• 2006

In a liquid rocket engine, the role of gas-liquid scheme injector as an acoustic resonator or absorber is studied experimentally for combustion stability by adopting linear acoustic test. The acoustic-pressure signals or responses from the chamber are monitored by acoustic amplitude. Acoustic behavior in a rocket combustor with a single injector is investigated and the acoustic-damping effect of the injector is evaluated for cold condition by the quantitative parameter of damping factor as a function of injector length. From the experimental data, it is found that the injector can play a significant role in acoustic damping when it is tuned finely. The optimum tuning-length of the injector to maximize the damping capacity is near half of a full wavelength of the first longitudinal overtone mode traveling in the injector with the acoustic frequency intended for damping in the chamber. When the injector has large diameter, the phenomenon of the mode split is observed near the optimum injector length and thereby, the acoustic-damping effect of the tuned injectors can be degraded.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 추계학술대회 논문집 학회본부
• /
• pp.544-549
• /
• 1997

Injector of high voltage or linear ion accelerator is intended to generate, extract and form beam of certain species with required parameters at the entrance of accelerating structure or, for low energy case, directly in the processing chamber (end station). Injector is the main part defining the ion accelerator performance and reliability. Its power supply and control system (PSCS) features are conditioned by placing the injector equipment at high voltage potential and by complexity of the plasma-beam load. The injector's PSCS should provide: - Transmission of electric power onto high voltage (h/v) terminal; - Obtaining of required output characteristics for injector equipment operation; - Transmission of the operational data and start/stop signals from h/v terminal to control cabinet; - Rremote control of injector; - Withstanding the high voltage breakdowns and X-ray radiation; - Compatibility with other equipment. The paper is concerned with analysis of injectors' PSCS structure and description of the system developed for 50 keV, 20 mA heavy ion injector.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2009년 춘계학술대회논문집
• /
• pp.130-134
• /
• 2009

CFD analysis of the fuel injection pattern and the flow field surrounding the liquid propellant injector of a small thruster is performed. A good agreement is shown with PIV test data for the initial configuration. Analysis on various injector shapes is performed to observe the effect of injector shape on the trajectories of liquid droplet. A various shapes of injector is investigated to enhance spray pattern of the small injector.

• 한국자동차공학회논문집
• /
• 제10권1호
• /
• pp.59-66
• /
• 2002

This paper presents the process of the needle lift estimation ova common-rail injector fur HSDI(High Speed Direct Injection) diesel engines. A nonlinear mathematical model of dynamic behaviors of common-rail injector is established at first. Based on the mathematical model of the common-rail injector, the methodology of estimating the injector needle lift is introduced. A sliding mode observer is applied to overcome the model uncertainties. The common-rail injector model and the needle lift estimator are verified by simulations and experiments. The simulation and experimental results indicate that the model outputs are in a good agreement with experimental data, and the proposed nonlinear sliding observer can effectively estimate the needle lift.

• International Journal of Aeronautical and Space Sciences
• /
• 제3권1호
• /
• pp.1-8
• /
• 2002

A numerical analysis was performed on the fluid flow in injector orifice of a liquid rocket engine. The present computational code was verified against the published data for turbulent flow in a pipe with a sudden expansion-contraction. Considered were the parameters for the flow analysis in an injector orifice: Reynolds number, ratio of mass flow rate of the injector orifice and inlet flow rate, and slant angle of the injector orifice. The discharge coefficient increased slightly as the Reynolds number increased. The slant angle of the injector changed critically the discharge coefficient. The discharge coefficient increased by 7% when the slant angle changed from $-30^{\circ}$ to $30^{\circ}$ The ratio of mass flow rate had relatively little impact on the discharge coefficient.

• 한국군사과학기술학회지
• /
• 제6권4호
• /
• pp.113-123
• /
• 2003

Both numerical analysis and experiment of cold and hot tests were performed to obtain basic design data for the swirl coaxial type Injector and to predict the combustion performance. Mass distribution, mixing distribution, mixing efficiency, characteristic velocity efficiency were measured by the cold tests and numerical analysis using the commercial thermo-hydraulic program. Test and analysis variables were recess, pressure drop, velocity ratio, mixing spray, mixture ratio. Hot tests were performed for the Uni-element injector to compare the performance with the cold test results, and, hot tests for Multi-element injector were performed to compare the performance with Uni-element injector. Designed thrust of the Uni-element injector liquid rocket was 35kgf at sea level and combustion chamber pressure, 20bar. Kerosene and Lox were used as a propellant.

• 한국분무공학회지
• /
• 제15권2호
• /
• pp.61-66
• /
• 2010

Fuel spray characteristics of the gasoline engine injector has been studied experimentally. To provide fundamental performance data of 4-hole and 12-hole injectors, spray fuel-mass distribution, wall wetting fuel amount and visualization of injectors have been tested and measured with various fuel supply pressure conditions. Spray visualization has been performed to analyze spray formation, spray angle, stream width and penetration length. Test result shows that wall wetting is greatly influenced by the induction air amount and spray atomization. Spray visualization shows that the 12-hole injector has robust performance characteristics with various fuel supply pressure conditions compared with the 4-hole injector. 4-hole injector generates relatively less wall-wetting fuel amount than 12-hole injector does.

• 한국군사과학기술학회지
• /
• 제9권4호
• /
• pp.137-144
• /
• 2006

단일요소 분사기(35kgf급)의 성능시험을 통해서 입증된 recess 2mm의 축소 모사된 로켓엔진(지상추력 250kgf급 다중요소 스월 동축형 분사기)을 설계, 해석, 제작, 시험하고, 이를 통하여 주요한 설계변수에 대한 검증과정을 수행하였다. 단일요소 및 다중요소 인젝터의 분무현상을 수치 해석적으로 모사하여 중첩에 의한 분무의 변화를 해석적으로 고찰하고 적용성 및 타당성을 확인하였다. 그리고 다중요소 분사기에 대한 연소성능시험을 통하여 엔진의 정상 연소성능을 평가하고 이를 단일요소 인젝터의 연소성능과 비교하여, 대형 로켓개발에 앞서 필요한 각 축소모델에 대한 특정 스케일에서의 다중요소 인젝터에 의한 연소성능을 평가하고 설계 자료를 확보, 합리적인 분사기 설계 변수자료를 확립하였다.

• 한국항공우주학회지
• /
• 제34권10호
• /
• pp.71-79
• /
• 2006

액체로켓엔진에서 고주파 연소불안정을 제어하기 위하여 다단 접선 유입구를 갖는 스월 인젝터를 분석하였다. 음향흡수자로서 인젝터의 효과를 분석하기위하여 인젝터는 1/4 파장 공명기로 해석하였고, 상온에서 감쇠 효과의 적합성을 검증하였다. 이러한 인젝터는 모델 챔버의 고유주파수에 동조시킬 수 있는 고유주파수를 갖게 된다. 다단의 접선 유입구를 갖는 인젝터가 단일 유입구를 갖는 인젝터 보다 인젝터 내부의 air core가 안정되었다. 또한, 다단 접선 유입구를 갖는 인젝터를 사용하였을 때 불안정 모드에 동조되는 인젝터 길이가 계산된 길이와 잘 일치하였다. 이러한 실험 결과로부터 인젝터 내부의 air core가 안정되게 유지된다면, 동조된 스월 인젝터는 모델 챔버의 불안정 모드를 효과적으로 감소시킬 수 있고, 감쇠율을 증가시킬 수 있음을 확인하였다.