• 소음진동
• /
• 제7권5호
• /
• pp.861-869
• /
• 1997

An approximate analytical method has been developed for estimating hydrodynamic forces acting on oscillating inner cylinder in concentric annulus. When the rigid inner cylinder executes translational oscillation, fluid inertia and damping forces on the oscillating cylinder are generated by unsteady pressure and viscous skin friction. Considering the dynamic-characteristics of unsteady viscous flow and the added mass coefficient of inviscid fluid, these hydrodynamic forces including viscous effect are dramatically simplified and expressed in terms of oscillatory Reynolds number and the geometry of annular configuration. Thus, the viscous effect on the forces can be estimated very easily compared to an existing theory. The forces are calculated by two models developed for relatively high and low oscillatory Reynolds numbers. The model for low oscillatory Reynolds number is suitable for relatively high ratio of the penetration depth to annular space while the model for high oscillatory Reynolds number is applicable to the case of relatively low ratio. It is found that the transient ratio between two models is approximately 0.2~0.25 and the forcea are expressed in terms of oscillatory Reynolds number, explicity. The present results show good agreements with an existing numerical results, especially for high and low penetration ratios to annular gap.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 1997년도 춘계 학술발표회 논문집 Proceedings of EESK Conference-Fall 1997
• /
• pp.207-214
• /
• 1997

The objective of this study is to review the current stare of earthquake simulation techniques using the shaking table and check the reliability. One degree-of-freedom(d.o.f.)and three d.o.f. aluminium shear models were used and 4m$\times$4m 6 d.o.f. shaking table was excitated in one horizontal direction to simulate 1940 El centro earthquake accelerogram (NS component). When the acceleration history of shaking table is compared to the desired one, it can be found that the overall histories are very similar, but that the lower frequency range (0~2 Hz) of the actual excitation has generally lower amplitude than that of the desired in fourier transform amplitude. Free vibration and white noise tests have shown almost the same values for natural frequencies, but shown quite different values for damping ratios, that is, 1.37% in case of r\free vibration test vs 14.76% in case of white noise test. The time histories of story shear versus story drift show the globally linear elastic behaviors. But the elliptical shape of the histories with one of the axis being the stiffness of the story implies the effect of viscous damping.

• 한국수소및신에너지학회논문집
• /
• 제23권4호
• /
• pp.404-411
• /
• 2012

This research numerically analyses the effects of the damping device on the operation characteristics of a free piston linear engine. In this paper, the free piston linear engine uses spring as a damping device. The investigated parameter is spring hardness which is varied at 0.5, 1, 2.9, and 14.7 N/mm. The effects of spring hardness on the dynamic characteristic, thermodynamic characteristic and electric power of the engine are investigated. Beside, the equivalent ratio is also changed to provide more information for this study. The simulation results show that, by increasing spring hardness from 0.5 to 14.7 N/mm, all of parameters related to dynamic characteristic such as piston velocity, acceleration, displacement, and frequency increase accordingly. Beside, the peak pressure in the cylinder and electric power are also increased when increasing spring hardness. The tendency is also observed at varied equivalent ratios.

• 한국안전학회지
• /
• 제25권2호
• /
• pp.55-64
• /
• 2010

Since various weathered soils are encountered in many domestic construction sites, it is necessary to estimate characteristics of natural weathered soils. However, the remolded sample of weathered soils are commonly used to estimate their characteristics because it is very difficult to sample weathered soils in undisturbed states. However, it is well known that the behavior of remolded sample is different from that of the undisturbed sample particularly in the dynamic response, because the particle structure of undisturbed sample maintains its original structure from the mother rock. Thus, to evaluate the influence of sampling method and preparation method on stress-strain behavior, the resonant column tests were performed on the block, tube samples, remolded samples with static compression and remolded samples with tamping of the weathered granite soils. The shear modulus of the remolded sample with tamping is larger than the other samples presumably due to the high tamping pressure enough to induce particle breakage. The tube samples show larger damping ratios than other samples. Furthermore, one-dimensional ground response analysis was performed to compare the results qualitatively.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.1083-1088
• /
• 2004

This paper deals with the vibration and stability of a circular cylindrical shaft, modeled as a tapered thin-walled composite beam and spinning with constant angular speed about its longitudinal axis, and subjected to an axial compressive force. Hamilton's principle and the assumed mode method are employed to derive the governing equations of motion. The resulting eigenvalue problem is analyzed, and the stability boundaries are presented for selected taper ratios and axial compressive force combinations. Taking into account the directionality property of fiber reinforced composite materials, it is shown that for a shaft featuring flapwise-chordwise-bending coupling, a dramatic enhancement of both the vibration and stability behavior can be reached. It is found that by the structural tailoring and tapering, bending natural frequencies, stiffness and stability region can be significantly increased over those of uniform shafts made of the same material. In addition, the particular case of a classical beam with internal damping effect is also included.

• Smart Structures and Systems
• /
• 제2권2호
• /
• pp.141-154
• /
• 2006

Recently, the Hilbert-Huang transform (HHT) has gained considerable attention as a novel technique of signal processing, which shows promise for the system identification and damage detection of structures. This study investigates the effectiveness and accuracy of the HHT method for the system identification and damage detection of structures through a series of experiments. A multi-degree-of-freedom (MDOF) structural model has been constructed with modular members, and the columns of the model can be replaced or removed to simulate damages at different locations with different severities. The measured response data of the structure due to an impulse loading is first decomposed into modal responses using the empirical mode decomposition (EMD) approach with a band-pass filter technique. Then, the Hilbert transform is subsequently applied to each modal response to obtain the instantaneous amplitude and phase angle time histories. A linear least-square fit procedure is used to identify the natural frequencies and damping ratios from the instantaneous amplitude and phase angle for each modal response. When the responses at all degrees of freedom are measured, the mode shape and the physical mass, damping and stiffness matrices of the structure can be determined. Based on a comparison of the stiffness of each story unit prior to and after the damage, the damage locations and severities can be identified. Experimental results demonstrate that the HHT method yields quite accurate results for engineering applications, providing a promising tool for structural health monitoring.

• Earthquakes and Structures
• /
• 제22권1호
• /
• pp.95-107
• /
• 2022

This paper introduces a novel, rigorous, and efficient probabilistic methodology for the performance-based optimal design (PBOD) of semi-active tuned mass damper (SATMD) for seismically excited nonlinear structures. The proposed methodology is consistent with the modern performance-based earthquake engineering framework and aims to design reliable control systems. To this end, an optimization problem has been defined which considers the parameters of control systems as design variables and minimization of the probability of exceeding a targeted structural performance level during the lifetime as an objective function with a constraint on the failure probability of stroke length damage state associated with mass damper mechanism. The effectiveness of the proposed methodology is illustrated through a numerical example of performance analysis of an eight-story nonlinear shear building frame with hysteretic bilinear behavior. The SATMD with variable stiffness and damping have been designed separately with different mass ratios. Their performance has been compared with that of uncontrolled structure and the structure controlled with passive TMD in terms of probabilistic demand curves, response hazard curves, fragility curves, and exceedance probability of performance levels during the lifetime. Numerical results show the effectiveness, simplicity, and reliability of the proposed PBOD method in designing SATMD with variable stiffness and damping for the nonlinear frames where they have reduced the exceedance probability of the structure up to 49% and 44%, respectively.

• Steel and Composite Structures
• /
• 제46권4호
• /
• pp.577-589
• /
• 2023

In this study, on-site testing was carried out to investigate the vibration performance of a cold-formed thin-walled steel floor system. Ambient vibration, walking excitation (single and double persons), and impulsive excitation (heel-drop and jumping) were considered to capture the primary vibration parameters (natural frequencies, damping ratios, and mode shapes) and vertical acceleration response. Meanwhile, to discuss the influence of cement fiberboard on structural vibration, the primary vibration parameters were compared between the systems with and without the installation of cement fiberboard. Based on the experimental analysis, the cold-formed thin-walled steel floor possesses high frequency (> 10 Hz) and damping (> 2%); the installed cement fiberboard mainly increases the mass of floor system without effectively increasing the floor stiffness and may reduce the effects of primary vibration parameters on acceleration response; and the human-structure interaction should be considered when analyzing the vibration serviceability. The comparison of the experimental results with those in the AISC Design Guide indicates that the cold-formed thin-walled steel floor exhibits acceptable vibration serviceability. A crest factor 𝛽_rp (ratio of peak to root-mean-square accelerations) is proposed to determine the root-mean-square acceleration for convenience.

• 한국강구조학회 논문집
• /
• 제22권6호
• /
• pp.553-561
• /
• 2010

본 논문은 점성 감쇠기를 가진 셀프 센터링 단자유도 시스템과 탄소성 거동을 하는 단자유도 시스템의 내진 성능을 해석적 연구를 통하여 두 시스템이 유사한 최대 변위 응답을 갖도록 하는 점성 감쇠기의 감쇠비를 근사적으로 구하는 것을 목적으로 한다. 우선, 점성 감쇠기를 가진 셀프 센터링 단자유도 시스템의 조화 반복 가력 시의 거동에 대하여 설명하고 거동을 구현할 수 있는 해석모델을 소개한 후 두개의 단자유도 시스템의 이력거동을 특징지을 수 있는 해석변수를 설정하고 20개의 역사지진을 사용하여 비선형 시간 이력 해석을 실시하였다. 대부분의 경우 약 10 ~ 15% 정도의 점성 감쇠비를 가진 셀프 센터링 단자유도 시스템이 탄소성 거동을 하는 단자유도 시스템과 유사한 평균 최대 변위 응답을 보였다. 아울러, 3개의 탄소성 거동을 하는 단자유도 시스템과 6개의 점성 감쇠기를 가진 셀프 센터링을 선택하여 두 시스템의 내진성능을 보다 자세히 조사한 결과, 점성 감쇠기를 가진 셀프 센터링 시스템이 진동이 끝난 후 잔류변형이 남지 않았을 뿐만 아니라 약 15%의 감쇠비를 가진 점성 감쇠기를 가진 셀프 센터링 시스템은 탄소성 거동의 단자유도 시스템보다 우수한 최대 변위와 가속도 응답을 보였다.

• 한국자동차공학회논문집
• /
• 제15권2호
• /
• pp.50-57
• /
• 2007

Shocks are excited by impulsive forces and cause discomfort in vehicles. Current standards define means of evaluating shocks and predicting their discomfort, but the methods are based on research with a restricted range of shocks. This experimental study was designed to investigate the discomfort of seated subjects exposed to a wide range of vertical shocks. Shocks were produced from the responses of one degree-of-freedom models, with 16 natural frequencies (from 0.5 to 16 Hz) and four damping ratios (0.05 0.1, 0.2 and 0.4), to a hanning-windowed half-sine force inputs. Each type of shock was presented at five vibration dose values in the range $0.35\;ms^{-1.75}$ to $2.89\;ms^{-1.75}$. Fifteen subjects used magnitude estimation method to judge the discomfort of all shocks. The exponent in Stevens' power law, indicating the rate of growth in discomfort with shock magnitude, decreased with increasing fundamental frequency of the shocks. At all magnitudes, the equivalent comfort contours showed greatest sensitivity to shocks having fundamental frequencies in the range 4 to 12.5 Hz. At low magnitudes the variations in discomfort with the shock fundamental frequency were similar to the frequency weighting $W_b$ in BS 6841, but low frequency high magnitudes shocks produced greater discomfort than predicted by this weighting. At some frequencies, for the same unweighted vibration dose value, there were small but significant differences in discomfort caused by shocks having different damping ratios. The rate of increase in discomfort with increasing shock magnitude depends on the fundamental frequency of the shock. In consequence, the frequency-dependence of discomfort produced by vertical shocks depends on shock magnitude. For shocks of low and moderate discomfort, the current methods seem reasonable, but the response to higher magnitude shocks needs further investigation.