• 한국초지조사료학회지
• /
• 제10권2호
• /
• pp.102-109
• /
• 1990

This experiment was carried out to study the effect of pure mineral nitrogen fertilizing on dry matter yield of grassland and the advisable mineral nitrogen amounts in long duration under practical conditions at the "Federal Institute for Agriculture in the Alps" in Austria. The application rates were 0, 30, 60,90 and 120 kg N/ha/cut, the cutting regimes 3-, 4-, 5- and 6-cuts/year. In order to explain the nitrogen-profitability were determined that 1 kg pure mineral nitrogen have to produce 8 - 16 kg DM/kg N in dependence on cutting regimes and requiring of nitrogen efficiencies. The results were as follows: 1. With only PK-fertilizaing average dry matter yields from 4.0 to 7.6 tons per ha and year were obtained. 2. Within all applied cutting regimes 60 kg min. Nlhalgrowth have proved to be the most efficient application rate witn 13 - 24 kg DM/kg N in dependent of cutting regimes. Comapred with only PK-treatment the DM yields increased by 3.9 - 4.7 t/ ha nad year. 3. By the sigmaformed process of Input-Output curve the highest marginal yield (the "most efficient" Ndressing rate) per ha and year was calculated: 152 kg N at 3-cut regimes, 204 kg N at 4-cut regimes, 220 kg N at 5-cut regimes and 240 kg N/ha/year at 6-cut regimes. 4. With required efficiencies of 16 and 12 kg DM/kg N 240 - 300 kg N per ha and year respectively would have to be applied at 3-cut regimes; with required efficiencies of 12 and 10 kg DM/kg N at 4-cut regimes the appropriate figures ranged from 320 to 420 kg N/ha and year, at 5- and 6-cut regimes and efficiencies of 10 and 8 kg DM/kg N results of 360 - 460 kg N and 380 - 500 kg N respectively were obtained. 5. At the relatively dry location Piber the highest dressing rates were needed in order to obtain the efficiencies from 8 to 16 kg DM/kg N, about 30 - 60 kg N/ha/year more than at the relatively moist location Admont.ist location Admont.

• 한국초지조사료학회지
• /
• 제14권4호
• /
• pp.257-263
• /
• 1994

The experiment was canied out to investigate the effects of cutting frequencies (3, 4 and 5 cuts per year) in relation to fertilization of mineral nitrogen on crude protein yield and the contents of crude protein and acid detergent fibre in orchardgms(Dacty1is glomerata L.). Tne results are as follows : 1. The content of crude protein increased according to the increase in cutting frequency and showed the highest in the 1st cut in all treatments. At 4 and 5 cutting frequencies per year, the content of crude protein increased in a large extent according to the increased fertilization of mineral nitrogen. However at 3 cutting frequency, the content of cmde protein appeared higher for no application of mineral nitrogen than for the treatments with fertilization. 2. 'Ihe content of acid detergent fibre(ADF) was considerably reduced at 4 and 5 cutting frequencies and in all treatments, the lowest were recorded in the 1st cut or in the last cut. At 3, 4 and 5 cutting frequencies, the highest ADF were shown in the 2nd cut, 3rd cut and 3rd cut respectively. However, the general trend was that the content of ADF was greatly reduced according to increased level of mineral nitrogen fertilization. 3. The yeild of cmde protein was the highest at 5 cutting frequency(l.2 ton DMIha) and it indicated that the yield of cmde protein increased in accordance to the increase in fertilization of mineral nitrogen and cutting frequency. 4. In all treatments, positive correlation(p<0.001) between the yeilds of crude protein and annual dry matter yield appeared. Negative correIation(p

• 한국환경복원기술학회지
• /
• 제5권1호
• /
• pp.19-27
• /
• 2002

To investigate the dominant species and factors related with plant coverage by road structures and forest environment factors, forest roads elapsed from one year to twelve year after construction had been selected in six county(Gochang-gun, Muju-gun, Imsil-gun, Jangsu-gun, Jeongup-shi and Jinan-gun), and 20m segments were continuously set up in each road. The results obtained from this study are summarized as follows: The species diversity of Gochang, Muju, Imsil, Jangsu, Jeongup and Jinan were 1.304, 1.267, 1.308, 1.193, 1.289 and 1.018, respectively. In process of years, plant coverage was increased gradually and average of plant coverage was 15.3% in forest roads which elapsed three year, and was 86.5% in forest roads which elapsed nine year after construction. The dominant species in the cutting slope of surveyed area were covered with Arundinella hirta, Pinus rigida, Miscanthus sinensis var. purpurascens, Artemisia princeps var. orientalis, Pinus densiflora, Oplismenus undulatifolius, Rubus coreanus, Lysimachia clethroides, Lespedeza bicolor, and Alnus hirsuta of the 152 species. The high correlated factors between plant coverage and variables in cutting slopes appeared elapsed year, soil hardness, mean annual precipitation, vertical grade, inslope and arid humidity in surveyed area.

• Asian-Australasian Journal of Animal Sciences
• /
• 제9권6호
• /
• pp.737-741
• /
• 1996

Dry matter yield of reed canarygrass was investigated in uncultivated rice paddy in Korea, and an attempt was made to estimate the most economic and efficient cutting frequency and rates of nitrogen (N) fertilization, for increased production of reed canarygrass. Total dry matter yields of reed canarygrass per year were 7.4-15.7, 8.5-16.1, and 7.5-13.4 tons/ha in 3, 4, and 5 cutting frequencies, respectively, and over the N treatments of 0-120 kg N/ha/cut. When cut 3 or 5 times annually, the 2nd cut produced the highest proportion of total yield at 38.4 and 33.0%, respectively, when cut 4 times the 3rd cut was highest (38.3%). The ranges of economic N level, limiting N level and efficiency of dry matter production were 243.3-293.0, 387.2, and 14.6 kg DM/kg N, respectively. These indicators were particularly low for the 5 cutting frequency possibly because of the unusually high temperature in the summer season. The best cutting frequency for the dry matter production of reed canarygrass in 1994 was 3 per year because of the higher efficiency of dry matter production.

• 한국초지조사료학회지
• /
• 제14권4호
• /
• pp.295-306
• /
• 1994

The object of this experiment was to suggest the suitable cutting frequency and cutting height for orchardgrass (0G)-red clover(RC) mixtures under the intensive system of short-term pasture utilization. The fields trials were conducted over 3-year period(1991-1993) to evaluate dry matter yield, botanical composition, chemical composition and CP, DDM yield on the cutting frequency (30, 40 and 50 days) and cutting height(5, 7 and 9cm) With decreasing the cutting frequency, the DM yield of OG in the OG-RC mixtures was significantly increased(P

• 환경생물
• /
• 제17권4호
• /
• pp.459-465
• /
• 1999

본 연구는 우리나라 습지의 주요 우점종인 갈대, 줄 및 애기부들을 대상으로, 자연습지에서 생육기 중에 시기와 횟수를 달리하여 지상부를 제거하는 것이 생산력과 영양염류 제거능에 미치는 영향을 규명하고자 하였다. 지상부 제거는 세 종 모두에서 지상부 생산력과 영양염류 흡수량을 증가시켰으며, 최대효과를 위한 시기와 횟수 및 효과의 정도는 종에 따라 차이를 보였다. 즉, 갈대는 1차년도 실험에서 6월 제거구의 연총생산력이 1,014g/$m^2$로서 대조구의 1.9배이었고, 2차년도에는 5월 제거구가 1,494g/$m^2$ 로서 대조구의 1.3배이었다. 줄은 8월 제거구의 생산력이 1,386g/$m^2$으로서 대조구의 1.2배, 애기부들은 6월과 8월의 3회 제거구와 8월 제거구의 생산력이 각각 1,670, 1,620g/$m^2$로서 대조구의 1.1~l.2배이었다. 영양염류 제거량에서 갈대는 질소와 인이 1차년도에서 대조구의 2.0배와 1.8배, 2차년도에서 각각 1.4배, 줄은 2.4배와 1.8배 그리고 애기부들은 1.8배와 1.9배로서 생산력의 증가비율보다 더 많은 영양염류를 제거하였다. 종합적으로 생산력과 영양염류 제거량 그리고 관리의 경제적인 측면을 고려할 때, 갈대는 5~6월과 10월의 2회, 그리고 줄과 애기부들은 8월과 10월의 2회 제거하는 것이 효과적인 것으로 판단한다.

• 유기물자원화
• /
• 제4권1호
• /
• pp.33-42
• /
• 1996

예취빈도와 액상구비의 시용수준에 대한 Reed canarygrass의 반응을 조사하여, 잠재생산성의 증대를 위한 경제적이고 합리적인 적정 예취빈도와 액상구비의 시용수준을 추정하고자 하였다. 예취빈도별 연간 건물수량에 대한 예취번초의 상대수량은 3회 예취구에서 2번초, 4회 예취구에서 3번초 및 5회 예취구에서는 4번초에서 다른 예취번초에 비해 가장 높은 상대수량을 나타내었다. 무시용구의 연간 건물수량은 예취빈도에 따라 6.4~7.5 ton/ha의 범위를 나타내었으며, 3회 예취구에서 가장 많은 연간 건물수량을 나타내었다. 액상구비의 시용수준이 증가됨에 따라서 연간 건물수량은 증가되었다. 즉, 3회 예취구에서는 연간 180 kg, 4회 예취구에서는 연간 120 kg 및 5회 예취구에서는 연간 300 kg로 증시하였을 때, 무시용구에 비해 유의하게 높은 건물수량을 나타내었다. 액상구비의 건물생산효율 (kg DM/kg N)은 3회 예취구의 120 kg/ha/cut, 4회 예취구의 30 kg/ha/cut 및 5회 예취구의 90 kg/ha/cut에서 각각 16.8, 25.4 및 10.4 kg 의 가장 높은 건물을 생산하였고, 시용시기에 따른 건물생산효율은 3회 예취구에서 1번초, 4회와 5회 예취구에서는 2번초에서 가장 높았다. 경제적 액상구비의 질소시용수준은 3회 예취구에서 462.7~525.3 kg/ha, 4회 예취구에서 353.1~423.2 kg/ha 그리고 5회 예취구에서 380.1~424.4 kg/ha의 범위를 나타내었다.

• The Korean Journal of Ecology
• /
• 제13권3호
• /
• pp.191-202
• /
• 1990

For the maximun yield of the forest trees in the forest management, the growth of annual ring area of the major forest trees was analysed in the four areas in South Korea. The time to the maximum productivity and the optimum cutting time for the maximum yield were estimated. The growth curve of annual ring area showed sigmoid like that of other organisms. Only the growth coefficient among the areas between Fraxinus rhynchophylla and Pinus koraiensis represented significance (5% level). The growth coefficient among forest trees between Pinus densiflora and Abies holophylla, Larix kaempferi and Carpinus laxiflora, Larix kaempferi and Quercus mongolica, Larix kaempferi and Quercus serrata, Larix kaempferi and Pinus koraiensis, and Larix kaempferi and Abies holophylla represented significance (5% level). Among eight forest trees, the time to maximum productivity (tm) of Larix kaempferi was the earliest (21.4 year), and Abies holophylla was the latest (91.9 year). The optimum cutting time for the maximum yield (tc) of L. kaempferi was the earliest (29.4 year) and that of A, holophylla was the latest (122.2 year) of all communities. The optimum cutting time for the maximum yield was 1.33 times as late as the time to the maximum productivity. If the growth of annual ring area as the forest tree for wood is regarded, L. kaempferi and P. densiflora are thought to be more economical than A. holophylla and P. koraiensis.

• 한국기계가공학회지
• /
• 제2권3호
• /
• pp.26-33
• /
• 2003

The term 'High Speed Machining' has been used for many years to describe end milling with small diameter tools at high rotational speeds, typically 10,000-100,000rpm. The process was applied in the aerospace industry for the machining of light alloys, notably aluminum. In recent year, however, the mold and die industry has begun to use the technology for the production of components, including those manufactured from hardened tool steels. With increasing cutting speed used in modern machining operation, the thermal aspects of cutting become more and mole Important. It not only directly influences in rate of tool weal, but also affects machining precision recognized as thermal expansion and the roughness of the surface finish. Hence, one needs to accurately evaluate the rate of cutting heat generation and temperature distributions on the machining surface. To overcome the heat generation, we used to cutting fluid. Cutting fluid plays a roles in metal cutting process. Mechanically coupled effectiveness of cutting fluids affect to friction coefficient at tool-workpiece interface and cutting temperature and chip control, surface finish, tool wear and form accuracy. Through this study, we examined the behavior of heat generation in high-speed machining and the cooling performance of various cooling methods.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 춘계학술대회 논문집(한국공작기계학회)
• /
• pp.422-428
• /
• 2001

The term High Speed Machining has been used for many years to describe end milling with small diameter tools at high rotational speeds, typically 10,000 - 100,000 rpm. The process was applied in the aerospace industry for the machining of light alloys, notably aluminium. In recent year, however, the mold and die industry has begun to use the technology for the production of components, including those manufactured from hardened tool steels. With increasing cutting speed used in modern machining operation, the thermal aspects of cutting become more and more important. It not only directly influences in rate of tool wear, but also will affect machining precision recognized as thermal expansion and the roughness of the surface finish. Hence, one needs to accurately evaluate the rate of cutting heat generation and temperature distributions on the machining surface. To overcome the heat generation, we used to cutting fluid. Cutting fluid play a roles in metal cutting process. Mechanically coupled effectiveness of cutting fluids affect to friction coefficient at tool-work-piece interface and cutting temperature and chip control, surface finish, tool wear and form accuracy. Through this study, we examined the behavior of heat generation in high-speed machining and the cooling performance of various cooling methods.