• Tribology and Lubricants
• /
• 제11권5호
• /
• pp.78-86
• /
• 1995

The silicon nitride based ceramic cutting tool materials have been fabricated by gas pressure sintering (GPS) or hot pressing (HP). Their mechanical properties were measured and the effect of the fabrication variables on the properties were examined. Also, effect of adding TiN or TiC particulates on the mechanical properties of the silicon nitride ceramics were investigated. Ceramic cutting tools (ISO 120408) were made of the sintered bodies. Cutting performance test were performed on either conventional or NC lathe. The workpieces were grey cast iron, hardened alloy steel (AISI 4140, HRc>60) and Ni-based superalloy (Inconel 718). The results showed that fabrication variables, namely, sintering temperature and time, exerted a strong influence on the microstincture and mechanical properties of the sintered body, which, however, did not make much difference in wear resistance of the tools. High hardness of the tool containing TiC particulates exhibited good cutting performance. Extensive crater wear was observed on both monolithic and TiN-containing silicon nitride tools after cutting the hardened alloy steel. Inconel 718 was extremely difficult to cut by the current cutting tools.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1997년도 추계학술대회 논문집
• /
• pp.76-81
• /
• 1997

In the past polyester was usually used as the matrix of all fiber-reinforced plastic (FRP). Nowadays, however, epoxy resin has taken the place of polyester due to its superior properties. If the cutting properties of epoxy resin are unknown, It is difficult to find the optimum cutting conditions of all fiber-reinforced plastic such as CFRP. AFRP. GFRP. In this paper, I will study the cutting properties of epoxy resin by testing surface roughness.

• 한국기계가공학회지
• /
• 제20권10호
• /
• pp.9-18
• /
• 2021

The cutting force in a cutting simulation is determined by the cutting conditions, such as cutting speed, feed rate, and depth of cut. The cutting force changes, depending on the material and cutting conditions, and is affected by the heat generated during cutting. The physical properties for predicting the cutting force use constitutive equations as functions of the hardening term, rate-hardening term, and thermal-softening term. To accurately predict the thermal properties, it is necessary to accurately predict the thermal-softening coefficient. In this study, the thermal-softening coefficient was determined, and the cutting force was predicted, using the response-surface method with the cutting conditions and the thermal-softening coefficient as factors.

• 한국의류산업학회지
• /
• 제6권4호
• /
• pp.497-502
• /
• 2004

The mechanical properties of jean slacks to the type of cutting lines in knee region and the bending time, after doing bending 0 times, 500 times, and 1500 times, the effects of whether or not cutting line, the fabric direction of the cutting area, and the number of cutting lines were investigated for tensile, shearing, compression, and mixing value of mechanical properties. The results are as follows: EM to bending times were larger in order of weft

• 펄프종이기술
• /
• 제40권2호
• /
• pp.57-64
• /
• 2008

In general, the entire of paper mulberry bark, which is not cut into pieces with an appropriate length, have been used in the pulping. This kind of pulping method couldn't accomplish the improvement of beating and sheet forming efficiency. For this reason, we investigated the effects of the cutting length of paper mulberry bast fiber on pulping and Hanji (Korean traditional paper) properties, in order to develop high quality Hanji manufacturing process. The cutting length variation of paper mulberry white bast did not great effects on pulp yields. The pulp yields based on pulping methods were sulfomethylated pulping av. 57.4%, alkali-hydrogen peroxide pulping av. 55.4%, and alkaline pulping av. 53.5% respectively. The optical properties such as brightness, opacity, scattering coefficient, and absorption coefficient were slightly improved by the increase of paper mulberry white bast cutting length. The increase of paper mulberry white bast cutting length resulted in poor sheet formation. Physical properties such as breaking length, TEA, tear index, burst index, and folding endurance were slightly improved by the increase of cutting length. The modified pulping processes, which used sulfomethylated method and alkali-hydrogen peroxide method, showed better pulp and sheet properties than conventional alkaline pulping.

• 한국터널지하공간학회 논문집
• /
• 제17권5호
• /
• pp.533-551
• /
• 2015

암석은 인공적인 재료(금속, 유리)에 비해 불균질하고 이방성을 가지고 있기 때문에 워터젯 절삭시 매우 복잡하게 파쇄되는 특성을 가진다. 워터젯 절삭시 암석특성에 따라 절삭성능이 결정되므로 물성에 대한 영향을 파악하는 것은 매우 중요하다. 워터젯 절삭효율에 영향을 미치는 물성은 선행문헌의 실험조건(수압, 연마재 투입량, 이격거리 등) 및 암종에 따라 다양하게 제시되고 있다. 본 연구에서는 워터젯 시스템을 이용한 암석절삭에 있어서 물성영향에 대해 문헌연구를 실시하고 중요 물성을 분석하였다. 선행문헌 연구를 통해 암석의 공극율, 일축압축강도, 경도가 워터젯 암석 절삭에 있어서 중요한 물성으로 도출되었다. 분석결과는 향후 워터젯 절삭 기술을 이용한 터널공사시, 암반특성에 따른 굴착효율을 예측하기 위한 기초지식을 제공할 수 있을 것이다.

• 한국정밀공학회지
• /
• 제18권4호
• /
• pp.182-189
• /
• 2001

TiCN based submicron cermet and similar ISO grad of the conventional cermets with TiCN of different particle size were produced by PM process, and their microstructure, mechanical properties and cutting performance were compared. The microstructure of submicron cermet was more homogeneous and showed much finer microstructure, resulting in better hardness and fracture toughness. The submicron cermet tools achieved excellent cutting performance such as wear resistance and toughness in comparison with two grades of the conventional cermets in millimg test. The relationship between microstrucure, mechanical properties and cutting performance of these cermet tools was discussed. The submicron cermet tools revealed for their potential to wide application range and interrupt cutting because of their superior wear resistance and toughness combinations.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 춘계학술대회 논문집
• /
• pp.143-148
• /
• 1995

A study on the generation of optimum tool path for machining the concave parts is discussed. Above all, the various cutting factors and their relationships are considered. Then optimum tool path for concave parts is generated on these cutting variables and their relationships. It is difficult for existing CAD/CAM systems tomachine the concave parts. For cutting the part even the experienced craft must give many attentions and muchtime since it needs consideration of various cutting conditions and geometric properties. The optimum tool path for the concave part is generated onnot only geometric properties byut also cutting conditions. We choose, as variables, feed and cutting direction for productivity, diameter of tool and constant(stable) cutting force for machining accuracy. The results are verified through simulation of the index of performance and cutting force.

• 오토저널
• /
• 제10권1호
• /
• pp.33-41
• /
• 1988

A turning (facing) test on Glass Fiber Reinforced Plastics was performed with several tool materials, e.g., cemented carbides, cermet and ceramic, and the wear patterns and wear rate were analyzed to clarify the relation between physical(mechanical) properties and flank wear of cutting tool. The main results are obtained as follows: (1) When cutting speed is increased, the flank wear in every tool material grows the abnormal wear in the shape of triangle at a certain speed, i.e., a critical speed. (2) When cutting speed is increased, the wear rate in experimental tool material starts to increase remarkably at a critical speed. (3) The thermal conductivity among the properties of the tool material and the thermal crack coefficient of it are almost in proportion to the critical speed. (4) The order of performance in tool materials for cutting GFRP is K 10, M10, P20, TiC, CB.

• 한국공간구조학회논문집
• /
• 제1권1호
• /
• pp.157-166
• /
• 2001

In general, the cutting pattern of the membrane structures is determined by dividing the complicated curved 3-D surface into several 2-D plane strip by using flattening technique. In this procedure, however, some discrepancies ore occurred between actual stresses of equilibrated state and designed uniform stresses because the material properties are not considered. These deviations can cause the critical structural problems, wrinkling or overstress, and thus a optimization process should be considered. In this paper, a new analytical method for determining an optimum cutting pattern considering material properties is presented. Here, iterative procedure is introduced to decrease the errors caused in numerical process. The optimization method proposed can diminish the deviations occurred by material properties and numerical errors, simultaneously. As a results, it is shown that the final stress distributions for the HP shell model are sufficiently near to design stress distributions, and it can be concluded that this method can be used to obtain the optimized cutting pattern of membrane structures.