• Journal of the Korean Institute of Navigation
• /
• v.23 no.1
• /
• pp.29-43
• /
• 1999

The production process of the compound-curved hull plates includes hull design, definition, fairing, modeling, lofting, cutting, and forming in sequence. Traditional fabrication methods and shop environment caused low level to productivity in medium and small sized shipyards. The most effective solution to solve those problems is to rationalize the layout of facilities. For the well-balanced development of domestic shipbuilding industry, it is urgently required to reduce the gap between modernized large sized shipyards and traditional small and medium sized shipyards in production technologies and efficiencies. For the efficient and accurate hull piece forming, all information from design to forming should be clarified and organized in a systematic manner. Thus, management of the information plays an important role in the computerized and automated of hull piece forming. The object of this paper is to survey the status of the field, to find out the feasibility and to introduce a draft of hull piece fabrication line for small and medium sized shipyards. The development of required system follows the object oriented technology to extend to simulation based system for carrying out physical product flow and facilities layout analysis. It is feasible to operate such a modernized facility for a group of small and medium shipyards who are unable to have each of their own facility because of its large amount of initial investment and insufficient work load.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.11
• /
• pp.148-154
• /
• 2001

Drilling is one of the most important operations in machining industry and usually the most efficient and economical method of cutting a hole in metal. From automobile parts to aircraft components, almost every manufactured product requires that holes are to be drilled for the purpose of assembly, creation of fluid passages, and so on. It is therefore desirable to monitor drill wear and hole quality changes during the hole drilling process. One important aspect in controlling the drilling process is monitoring drill wear status. A drill-wear monitoring system provides information about drill status. With the information, optimum planning for tool change is possible. And drill-wear monitoring system in needed to evaluated drilled hole quality and the wear of drill. Accordingly, this paper deals with an on-line drill wear monitoring system of the detection of tool wear with the computer vision and the area of the drill flank wear is analyzed quantitatively by the system.

• Journal of The Korean Association of Information Education
• /
• v.22 no.5
• /
• pp.605-611
• /
• 2018

On-Line Lectures are becoming more common due to the MOOK service and the expansion of national policy in Korea. Especially, It is being changed to new remote mixed style from traditional lecture in universities. We propose and implement a remote contents making tool with audio synchronization function based on more with less resources. To implement our proposed algorithm, we design an interactive interface to assign multiple cutting intervals and convert an input video to print a new result. In experimental, we can confirm our algorithm works properly with average performance value 9.3% cpu share ratio and 87mega byte ram usage(CPU 2.60GHz, 820*600 Area).

• International Journal of High-Rise Buildings
• /
• v.6 no.4
• /
• pp.297-300
• /
• 2017

Employers are realizing that workplaces have an immense impact on productivity. And, because people typically represent about 90% of a company's costs, even a slight improvement in productivity hits the bottom-line in a very big way. The focus is shifting away from saving money by reducing space needs or cutting energy requirements, and moving toward making the workplace friendlier and healthier. What is a healthy workplace, exactly? The answer should be clear by now. Mountains of research have expounded on this very topic, and then news outlets cover the latest discoveres ad infinitum. The problem is, research is rather dense, while the news isn't comprehensive. Office managers trying to improve workplace wellness want neither a 55-page report nor a half dozen articles to convince their landlord that their space can do better. Recognizing this gap, Harvard researchers have released a concise-yet-complete list of healthy building features. Here, we're sharing these nine features with a few insights of our own on the value of being healthy and productive. Find out: ${\bullet}$ What makes a healthy building and why is it so important ${\bullet}$ How to improve the health of your own office ${\bullet}$ What happens for your people and your bottom line when you make health a priority.

• Journal of the Korean Society for Heat Treatment
• /
• v.37 no.5
• /
• pp.215-220
• /
• 2024

Slip lines and dislocation structures developed by deformation at 77 K, 292 K and 500 K have been investigated by an optical microscope and a high-voltage electron microscope. Slip patterns after the deformation by 4-5% at 77 K and 500 K are compared. From the slip line geometry, operation of both primary and secondary {111} slips have been confirmed. However, the primary slip lines formed at 77 K appear coarser and more pronounced than those at 500 K. This indicates that a larger number of dislocations have moved on the same plane at 77 K. Another characteristic difference noted here is that the slip lines are straight and pass through the specimen from one end to the other at 77 K. On the contrary, slip lines are rather faint at 500 K. The typical change found at 77 K is the increase in the [$0{\bar{1}}1$] dipole dislocations and generation of the [$10{\bar{1}}$] screw dipoles upon increase in the strain from 1.2% to 5.2%. This is the indication that the straight dipole dislocations were formed by a pinning effect due to jogs generated by mutual cutting between primary and secondary dislocations. Extremely fine slip has been noted after deformation at 500 K indicating that the usual Frank-Read source is not operative at high temperatures due to the strong KW locking.

• Journal of Korean Society of Forest Science
• /
• v.106 no.1
• /
• pp.1-9
• /
• 2017

Forest harvest as large scale artificial disturbance makes edge environment in both clear-cutted and forested habitat. To clarify the development and recovery process of forest edge after disturbances is essential to understand vegetation responses and landscape level consequences such as edge-distance. In Korea, after clear-cutting, edge-related changes of environment and vegetation was not clarified yet. In Korean red pine (Pinus densiflora) forest, by applying space-for-time approach (sites with undisturbed and 1, 3, 10, 16 yr after cutting), the edge-related change of plant abundance and abiotic factors were determined for 20 line-transect (60 m) and 340 ($1m{\times}5m$) quadrats, and clarified depth and duration of the disturbance. Immediately after edge formation, within 15m form the edge, biotic and abiotic factors such as cover, richness, canopy openness, temperature and moisture content exhibited larger changes compared to forest interior. Plant abundance and abiotic variables were stabilized at the level of forest inside within 16 yr and 10 yr after edge creation, respectively. Woody (tree and shrub) species generally was showed larger increment with proximity to edge than did herb or graminoid species. In addition, negative interactions between woody and herbaceous species were detected during the period of forest edge closure. Our results suggested that depth of forest edge formed by clear-cutting of Korean red pine forest was at least from 15 m to 20 m and edge effect were likely sustained more than 16 years. As the first empirical study on edge-distance between two contrast habitats of clear-cutted and adjacent forest in South Korea, the analytical reality on landscape structure and habitat patches can be improved.

• Journal of Animal Science and Technology
• /
• v.48 no.3
• /
• pp.443-452
• /
• 2006

The four rice(Oryza sativa L.) lines, previously demonstrated to have vigorous herbage production at the vegetative growth stage, were investigated for their growth traits, dry matter yield and feed value using the twice-cutting system that 1st-cut is harvested at panicle formation stage and 2nd-cut at the yellow ripen stage. The twice-cutting system is regarded as an effective method in the production of forage rice by escaping lodging and insect damages caused by the overgrowth and typhoon around the heading stage.The feed value of the twice-cut rice plant of there lines were compared with the control of normal, cutting at the yellow ripen stage. The relative feed value(RFV), the total digestible nutrient(TDN) and the crude protein(CP) content of the twice-cut straw were higher the control in every lines. However, the dry matter yield (DMY), represented by the summed forage production of 1st and 2nd cut-rice plant, were lower the control, and the DMY of straws were increase but grains were decrease for twice-cutting system. In addition, TDN yield showed the similar tendency with DMY.Recently, as one of the breeding aims the researches for improving the digestibility of rice straw have been required. In this regard, twice-cutting system is recognized with the fact that it has the effect which raises the digestibility of the straw. Especially, the 2nd cut of IR73111-B-R-15-3-1 line was similar to the control at the TDN yield of straw, and would be used as a breeding material for product the roughage of good quality.

• Journal of Biosystems Engineering
• /
• v.4 no.1
• /
• pp.1-23
• /
• 1979

The use of barley seeder attached to rotary tiller in the rural area has a significant meaning not only for the solution of labor peak season, but also for the increase of land utilization efficiency. The facts that presently being used barley seeders are all based on the mechanical principles of the reverse rotation, center drive and are all using forward rotating tine, which is used to be easily and heavily worn out when it rotates reversely, raise problem of recommending them to rural area in Korea. Therefore, the main objective of the study was to develop new type of rotary tine attachable to barley seeders. To attain the objective the following approaches were applied. (1) The kinematic analysis of reverse rotating barley seeders. (2) The studies on the soil bin and artificial soil. (3) The comparative experiment on the power requirement of prototype tine. The results obtained from the studies are summarized as follow: 1. The kinematic analysis of barley seeder attached to rotary tiller: The following results were obtained from the kinematic analysis for deriving general formulae of the motion and velocity characterizing the rotary tine of barley seeders presently being used by farmers. a) The position vector (P) of edge point (P) in the rotary tine of reverse rotating, center drive was obtained by the following formula. $$P=(vt+Rcos wt)i+Rsin wt j+ \{ Rcos \theta r sin \alpha cos (wt- \beta +\theta r) +Rsin \theta r sin \alpha sin (wt-\beta + \theta r) \} lk $$ b) The velocity of edge point $(P^')$ of reverse rotating, center drive rotary tine was obtained by the following formula. $$(P^')=(V-wR sin wt)i+(w\cdot Rcoswt)j + \{ -w\cdot Rcos \theta r\cdot sin \alpha \cdot sin (wt-\beta +\theta r) + w\cdot Rsin \theta r\cdot sin \alpha \cdot cos (wt- \beta + \theta r \} k $$ c) In order to reduce the power requirement of rotary tine, the angle between holder and edge point was desired to be reduced. d) In order to reduce the power requirement, the edge point of rotary tine should be moved from the angle at the begining of cutting to center line of machine, and the additional cutting width should be also reduced. 2. The studies on the soil bin and artificial soil: In order to measure the power requirement of various cutting tines under the same physical condition of soil, the indoor experiments Viere conducted by filling soil bin with artificially made soil similar to the common paddy soil and the results were as follows: a) When the rolling frequencies$(x)$ of the artificial soil were increased, the densIty$(Y)$ was also increased as follows: $$y=1.073200 +0.070780x - 0.002263x^2 (g/cm^3)$$ b) The absolute hardness $(Y)$ of soil had following relationship with the rolling frequencies$(x)$ and were increased as the rolling frequencies were increased. $$Y=37.74 - \frac {0.64 + 0.17x-0. 0054x^2} {(3.36-0.17x + 0.0054x^2)^3} (kg/cm^3)$$ c) The density of soil had significant effect on the cohesion and angle of internal friction of soil. For instance, the soil with density of 1.6 to 1.75 had equivalent density of sandy loam soil with 29.5% of natural soil moisture content. d) The coefficient of kinetiic friction of iron plate on artificial soil was 0.31 to 0.41 and was comparable with that of the natural soil. e) When the pulling speed of soil bin was the 2nd forward speed of power tiller, the rpm of driving shaft of rotary was similar to that of power tiller, soil bin apparatus is indicating the good indoor tester. 3. The comparative experiment on the power requirement of prototype tine of reverse rotating rotary: According to the preliminary test of rotary tine developed with various degrees of angle between holder and edge pcint due to the kinematic analysis, comparative test between prototype rotary tine with $30 ^\circ $ and $10 ^\circ$ of it and presently being used rotary tine was carried out 2nd the results were as follows: a) The total cutting torque was low when the angle between holder and edge point was reduced. b) $\theta r$ (angle between holder and edge point) of rotary tine seemed to be one: of the factors maximizing the increase of torque. c) As the angle between holder and edge point ($\theta r$) of rotary tine was $30 ^\circ $ rather than $45 ^\circ $, the angle of rotation during cutting soil was reduced and the total cutting torque was accordingly reduced about 10%, and the reduction efficiency of total cutting torque was low when the angle between holder and edge point ($\theta r$) of rotary tine was $10 ^\circ $, which indicates that the proper angle between holder and edge point of rotary tine should be larger than $10 ^\circ $ and smaller than $30 ^\circ $ . From above results, it could be concluded that the use of the prototype rotary tine which reduced the angle between holder and edge point to $30 ^\circ $, insted of $45 ^\circ $, is disirable not only decreasing the power requirements, but also increasing the durabie hour of it. Also forward researches are needed, WIlich determine the optimum tilted angle of rotary brocket, and rearrangement of the rotary tine on the rotary boss.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.9
• /
• pp.5419-5424
• /
• 2014

A weld scallop is a small quadrant or half circle type hole installed in the weld line cross area for easy welding operation. Many types of T-bars with a scallop can be welded in a block assembly stage in shipbuilding. The difficulties arise from the fact that scallops are to be filled by build-up welding after welding of the cross line is complete. In this study, a non-scallop block joint welding method was developed using special type CBM (ceramic backing material). The wedge shaped CBM was devised to insert a CBM into just the V groove of weld line cross area without weld scallop. A saw-toothed shape was adopted for easy cutting of the unnecessary part in the CBM fitting process. The applicability of the developed method was verified through welding experiments based on the yard welding conditions.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.35 no.8
• /
• pp.991-1005
• /
• 2011

This study researches the historical production, process, and design method for 3 pairs of corsets in $18^{th}$ century France. In the analytical stage of historical materials, it grasped the kind, form, origin, and change in style through a lexical definition of relevant terms. Through a precedent study on Garsault's 'L'art du tailleur', preservation costume, and historical reconstruction of pattern in preservation costume, it confirmed corps size, silhouette, pattern form, and material for historical production. The sewing method and the producing sequence were analyzed. In the production stage, 3 selective models in corps plein baleine, corps demi-baleine, and corset were historically produced. With neckline of forming broad Letter U, the bust part is covered roundly. The bodice was composed of 10 panels based on the corps form in the mid-$18^{th}$ century of following a curve of a human body. A shoulder strap was allowed to make the arm movement comfortable by producing and attaching it separately. The cutting line except the center in the front and the back of vertical line was distributed according to the natural flow of a form and movement of the human body. The curve-based pattern line was confirmed.