• Laser Solutions
• /
• 제13권2호
• /
• pp.10-16
• /
• 2010

Laser-assisted machining is dependent on absorbed energy density into workpiece. Generally, the absorptivity of laser beam is dependent on wave length of laser, materials, surface roughness, etc. Various shapes and energy densities for beam irradiation can be used to laser-assisted machining. In this thesis, efficient method of heat source modeling was developed and designed by using one fundamental experimental trials. And then, laser-assisted machining of rod-shaped cast iron was simulated by using commercial FEM code MARC. Simulations and experiments with various conditions were carried out to determine suitable condition of pre-heating for laser-assisted turning process. Temperature distribution of cutting zone could be predicted by simulation.

• Journal of Powder Materials
• /
• 제24권5호
• /
• pp.389-394
• /
• 2017

Ni wires with a diameter and length of 0.4 and 100 mm, respectively, and a purity of 99.9% are electrically exploded at 25 cycles per minute. The Ni nanopowders are successfully synthesized by a pulsed wire evaporation (PWE) method, in which Ar gas is used as the ambient gas. The characterization of the nanopowders is carried out using X-ray diffraction (XRD) and a high-resolution transmission electronmicroscope (HRTEM). The Ni nanopowders are classified for a multilayer ceramic condenser (MLCC) application using a type two Air-Centrifugal classifier (model: CNI, MP-250). The characterization of the classified Ni nanopowders are carried out using a scanning electron microscope (SEM) and particle size analysis (PSA) to observe the distribution and minimum classification point (minimum cutting point) of the nanopowders.

• Food Science and Preservation
• /
• 제11권2호
• /
• pp.148-153
• /
• 2004

The organoleptic properties of granule tea was optimized for granulation of Polygonatum sibiricum Delar(Dunggulle) tea for exclusion of scorched smell and increase of consumption. The length of 2 mm was suitable to cutting size of Dunggulle for preparation of the roasted Dunggulle. The optimum sensory conditions for aroma of Dunggulle granule tea showing 7.85 organoleptic score were 80.61% in ratio of Dunggulle extracts to total extracts, 12.77% in content of total extracts and 37.33% in rate of glucose to total sugar. The highest score of overall palatability was 5.96 at 61.11% in rate of Dunggulle extracts to total extracts, 13.79% in content of total extracts, and 60.92% in rate of glucose to total sugar.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 1998년도 춘계학술대회 논문집
• /
• pp.19-23
• /
• 1998

Water tree degradations have been considered as one of the most important causes of failure in underground distribution cables with polymeric insulation. Water tree growth is a preliminary step in the sequence of electrical tree initiation and electrical breakdown of the insulation. In this paper, needle electrode is made use of the etching methods and the pellet type specimen is made to observe the water tree in succession. In previous methods are able to observe the tree degradations without cutting and dyeing. The water tree image is recorded on VTR with CCD camera. The tree length of X, Y axis direction and aging area(treeing area) are calculated with image measurement. As a result of this study, water tree is observed by non-destructive method. Electrical tree is initiated from needle electrode tip only but water tree is initiated from total area of water electrode. Electrical tree owing to water treeing is initiated at low electric field and grown with discontinuously. Namely, water tree is shown up a different characteristics of tree growth.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제7권2호
• /
• pp.315-323
• /
• 2015

The weld scallop has been used for joining T-bars. There are a lot of weld scallops in shipbuilding. It is difficult to perform scallop welding due to the inconvenient welding position. This results in many problems such as porosity, slag inclusion, etc. In this study, a new method is devised to remove weld scallops by incorporating a Ceramic Backing Material (CBM). The weld scallop is removed by an elongation of the v groove. In order to insert a CBM into the groove without a weld scallop, a wedge-shaped CBM is developed. The top side of the developed CBM is similar to the shape of a general back bead. The bottom surface has a saw-toothed shape for cutting at a suitable length. This can be attached to the root side of a face plate using adhesive tape, just like a general CBM. Welding experiments in normal and abnormal conditions are carried out and the possibility of burn-through is examined. This CBM's applicability to shipbuilding is verified.

• Steel and Composite Structures
• /
• 제18권3호
• /
• pp.739-756
• /
• 2015

This paper presents investigations on the hysteretic behavior of concrete-filled circular tubular (CFCT) T-joints subjected to axial cyclic loading at brace end. In the experimental study, four specimens are fabricated and tested. The chord members of the tested specimens are filled with concrete along their full length and the braces are hollow section. Failure modes and load-displacement hysteretic curves of all the specimens obtained from experimental tests are given and discussed. Some indicators, in terms of stiffness deterioration, strength deterioration, ductility and energy dissipation, are analyzed to assess the seismic performance of CFCT joints. Test results indicate that the failures are primarily caused by crack cutting through the chord wall, convex deformation on the chord surface near brace/chord intersection and crushing of the core concrete. Hysteretic curves of all the specimens are plump, and no obvious pinching phenomenon is found. The energy dissipation result shows that the inelastic deformation is the main energy dissipation mechanism. It is also found from experimental results that the CFCT joints show clear and steady stiffness deterioration with the increase of displacement after yielding. However, all the specimens do not perform significant strength deterioration before failure. The effect of joint geometric parameters ${\beta}$ and ${\gamma}$ of the four specimens on hysteretic performance is also discussed.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• 제22권1호
• /
• pp.70-79
• /
• 1977

Perennial weeds which were grown in transplanted paddy field formed their tubers under shortday condition. Under short day treatment, the induction periods for tuber formation were different depending upon the weed species. 80% cut tubers of the weeds did not loose their developing ability perfectly. Emergence also affected by soil conditions and depths covered.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.1061-1062
• /
• 2007

In this paper, the analysis of some possibilities for increasing the induction motor efficiency is reported. This approach does not require a complete redesign of new laminations with a consistent cost in terms of investments. This paper shows the efficiency of the rectangular core types according to core-cutting-degree and compares the efficiency of the rectangular core types with the round core types. In particular, for obtaining an increase in efficiency, increase of the core axial length has been taken into consideration. The paper shows the results obtained by the finite element method(FEM) and IEEE Std. 112-96 Method B and analyzes the results to get a high efficiency for the induction motor.

• Journal of the Society of Naval Architects of Korea
• /
• 제31권1호
• /
• pp.121-132
• /
• 1994

The aim of the present paper is to clarify the damage characteristics fur ship bottom stiffened platings in grounding. For this purpose, a series of tests are performed. A rigid wedge is quasi-statically pushed into the high tensile steel plates with two stiffeners. The aspect ratio of plates(a/B) is in the range from 1.0 to 2.5 and the thickness of plates is in the range from 3.4 to 7.0mm. Also other parameters, namely the shape of wedge tip, wedge angle and property/direction of stiffeners are varied. The test is carried out using the 100ton universal test machine. During the loading. both applied force and length of cutting(penetration) resulting in the grounding force-penetration response are measured.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• 제21권9호
• /
• pp.12-20
• /
• 2022

Delamination and burr defects are important problems in drilling fiber reinforced plastics. A method for measuring FRP drilling defects has been studied. Delamination and burr factors were defined as the relative length or area. Using these factors, the effects of tool shape and drilling conditions on delamination and burr were studied. In this study, the defects that occur when drilling a glass-carbon fiber hybrid composite were compared in terms of three factors. In the glass-carbon fiber hybrid composite, the effects of the feed rate and tool point angle on the delamination and burr factors were similar to those in previous studies. The diameter of the tool did not affect the defect factor. A circular burr was generated in a drill tool with a point angle of 184°, and a relatively small deburring factor was observed compared with a tool with a point angle of 140°.