• Membrane Journal
• /
• v.13 no.4
• /
• pp.211-218
• /
• 2003

The removal characteristics of cadmium in micellar enhanced ultrafiltration (MEUF) were investigated by using an anionic biosurfactant, deoxycholic acid (DCA). The ultrafiltration experiments were performed in a batch-type stirred cell. The ultrafiltration membranes used were Millipore YM1, YM3, YM10, and YM30 which had a difference in molecular weight cut-off. The presence of cadmium ion in DCA solution tends to reduce the critical micell concentration considerably and increase the micell size. The molecular weight cut-off of ultrafiltration membrane had a minimal effect on cadmium removal whereas DCA/Cd ratio had a substantial influence. When DCA/Cd ratio was 3, the removal efficiency of cadmium was more than 99.6%. A relative flux, which is defined as ratio of the flux for a separation trial to that of deionized water run using the same piece of membrane, decreased in the order of YM3 > YM1 > YM10 > YM30.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.35C no.12
• /
• pp.13-22
• /
• 1998

In this paper, we propose a high-performance BICS(built-in current sensor) which is fabricated in 0.8${\mu}{\textrm}{m}$ single-poly two-metal process for IDDQ testing of CMOS VLSI circuit. The CUT(circuit under test) is 4-bit full adder with a bridging fault. Using two nMOSs that have different size, two bridging faults that have different resistance values are injected in the CUT. And controlling a gate node, we experimented various fault effects. The proposed BICS detects the faulty current at the end of the clock period, therefore it can test a CUT that has a much longer critical propagation delay time and larger area than conventional BICSs. As expected in the HSPICE simulation, experimental results of fabricated chip demonstrated that the proposed BICS can exactly detect bridging faults in the circuit.

• Korean journal of applied entomology
• /
• v.4
• /
• pp.7-10
• /
• 1965

In an experiment to evaluate the various aspects of symptom of witches' broom of jujube tree with two different kinds of scions, taken from diseased plant and stem- grafted upon sound stocks-one cut before wintering(stored in cellar), the other after wintering, it was observed that the disease rate of those cut before wintering(Nov.) was $\98\%$ whereas those cut after wintering(March) showed much lower rate, $3\%$ initially and gradually increased up to $39\%$. In another experiment of diseased bud grafted into healthy seedling, the finding made in the following year was that 14 stocks(only one of which salt union by callusing) were infected out of the given 23- in the initial stage only 4, yet gradually increased to the number of 14. The shoots from the ground portion of the diseased stock were in general more quickly subjected to the disease than the others. Under natural condition, the diseased trees develop at first seemingly the same leaves as healthy ones; it is not until the branches and loaves grow to a considerable degree that the symptom appears. Once appearing, tile disease grows and the symptom continues to appear as late as in Sept. and early Oct., causing tile plant to develop the extraordinary branches and leaves of extremely reduced size, the typical symptom of witches' broom. Such phenomenon can be observed in the experiments of the foregoing paragraphs. And the suckers and roots of diseased plant are bound to be infected, it was found out with no exception. Viewing from the results of the above experiments and observation, it is believed that the low temperature during winter causes the virus in the above-ground portion of diseased plant to diminish or inactivated, and subsequently the virus in the roots moves up or multiply in the sprouting season.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.2
• /
• pp.146-153
• /
• 1998

The optical near-field patterns, propagation loss and mode sizes of x-cut $Ti:LiNbO_3$ optical waveguide which was fabricated by Ti-diffusion varying with Ti strip thickness in wet oxygen atmosphere were discussed at optical wavelength 1550nm. As Ti thickness increased from $760{\AA}$, the insertion loss of waveguide was decreased. But at Ti thickness $1500{\AA}$, mode sizes are widely broadened. The Ti thickness of below $1100{\AA}$ and above $1500{\AA}$ showed negative effects to propagation loss and fiber coupling. The best Ti thickness for fabricating low propagation loss and good fiber coupling was inferred to be between $1100{\AA}-1500{\AA}$ in our conditions. And for Ti thickness $1150{\AA}$, its propagation loss, horizontal/vertical mode sizes were showed 1.61 dB/cm, $11.9/8.9{\mu}m$ for TM, 0.22 dB/cm, $12.0/9.1{\mu}m$ for TE respectively.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.55-55
• /
• 2009

FGB(Flexible Glasswool Backing) Submerged Arc Welding has been one of the main welding processes for one side butt welding in shipbuilding industries, which can efficiently improve the welding productivity by the addition of a supplementary filler metal into the molten weld pool. As recent ships have become larger in size, the application of high tensile and higher grade of steels has been continuously increased. Single pass FGB SA welding process accompanies such a high heat input when welding thick plates that the mechanical properties of weld metal can be dramatically degraded. This study has been performed in order to obtain high toughness and tensile properties of high heat input FGB SA welds, and to evaluate the effect of alloy elements on their mechanical properties. To complete welding 25mm-thick EH36 grade steel plate by single pass, 1.2mm diameter and 1.0mm long cut wires has been distributed in the groove before welding, and three different test coupons have been made using C-1.5%Mn, C-1.8%Mn-0.5%Mo, and C-1.4%Mn-1.7%Ni cut wires to investigate the influence of nickel(Ni) and molybdenum(Mo) on the mechanical properties of welds. Test results showed that the addition of Ni and Mo effectively promotes the formation of Acicular Ferrite(AF), while significantly reducing the amount of Grain Boundary Ferrite(GBF) in weld metal microstructures, which resulted in a beneficial effect on low temperature impact toughness and strength.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.2
• /
• pp.257-262
• /
• 2017

In this paper, we proposed a rectangular planar monopole antenna with a double sleeve that applied to a half-cut and a discontinuous feed structure. A rectangular planar monopole antenna with a double sleeve was cut in half along the magnetic symmetry line, and impedance matching was achieved by a discontinuous structure was applied to a feeder and by adjusting the double sleeve gap. We used the HFSS simulator of ANSYS company to confirm the antenna parameter property, and the antenna size was $21{\times}40mm^2$. In the proposed antenna, the simulation frequency range with VSWR of 2 or less was 2.6GHz to 10.25GHz. The bandwidth was 7.65GHz. The frequency range of the fabricated antenna was 3.3GHz to 9.75GHz, and the bandwidth was 6.45GHz. The measured radiation pattern frequencies were 3.5GHz, 5.5GHz, 7.5GHz, and 9.5GHz. A radiation pattern similar to the dipole antenna pattern was obtained at all frequencies.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.6
• /
• pp.711-718
• /
• 2019

BDD is a well-known alternative to the conventional Boolean logic method in fault tree analysis. As the size of fault tree increases, the calculation time and computer resources for BDD dramatically increase. A new failure path search and path restructure method is proposed for efficient calculation of CS and MCS from BDD. Failure path grouping and bottom-up path search is proved to be efficient in failure path search in BDD and path restructure is also proved to be used in order to reduce the number of CS comparisons for MCS extraction. With these newly proposed methods, the top event probability can be calculated using the probability by ASDMP(Approximate Sum of Disjoint MCS Products), which is shown to be equivalent to the result by the conventional MCUB(Minimal Cut Upper Bound) probability.

• Journal of IKEEE
• /
• v.26 no.2
• /
• pp.249-256
• /
• 2022

The prosthetic leg is a device that performs walking instead of a amputated lower limb, and require a change in locomotion mode by providing the user's intention to respond to a discontinuous locomotion environment. Research has been conducted to detect the users' intentions through biomechanical features inside the socket that directly contacts the cut site in demand for natural locomotion mode changes without external control equipment. However, there is still a need for a sensor system that is suitable for the internal environment of the main body and socket of the cut site. Accordingly, this paper proposed a film-type sensor system that is suitable for the main body characteristics of the cut site, is not affected by the temperature and humidity conditions inside the socket, and is easy to manufacture in various sizes. The proposed sensor is manufactured base on Velostat film and takes into account the pressure measurement characteristics that vary with size. Through the experiment, the change in the internal pressure of the socket due to the intentional posture performance of the wearer was measured, and the possibility of detecting the intention to change the locomotion mode was confirmed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.11
• /
• pp.1584-1589
• /
• 2013

A new and significantly small guided and resonant structure is suggested to take over bulky metallic hollow waveguides used in military satellite transceivers. Below Ku-band, the conventional waveguides resulting in quite heavy transceivers will be replaced by the low profile SIW(substrate integrated waveguide) structures that are distinguished from the others in that the suggested ones have much lower cut-off frequencies by the circuital configuration of DNG(dobule negative) constitutive parameters and become even smaller than the other SIWs. The design scheme is validated by the circuit and full-wave simulations from the guided, resonant, and coupled structures. Besides, a bandpass filter as the suggested coupled structure is fabricated with a cheap substrate in a low-budget fabrication process and its frequency response is measured as verification of the purpose of the design.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.12
• /
• pp.76-81
• /
• 2000

Analysis on failure of the panel glass under mechanical shock is the main topic of this study. Since the glass for the LCD panel is thin, it needs to be designed to have enough toughness against mechanical shock. In this paper, a process of estimating fracture of the panel glass is proposed to guarantee reliability of the product. The fracture toughness of the panel glass is used as a criterion of the fracture based on an experimental approach. The stress intensity factor was calculated considering a model with the largest initial crack size on a cut surface and with the boundary force obtained from a dynamic finite element analysis. Critical surface roughness on the cut surface of a typical glass panel, to prevent fracture in case of bending mode, is obtained.