• Journal of The Korean Society of Agricultural Engineers
• /
• v.65 no.6
• /
• pp.51-63
• /
• 2023

To improve the problem that the settlement curve of the consolidation theory of Terzaghi does not match well with the actual settlement curve, we included a secondary compression settlement and analyzed it by varying the beginning point and then obtained the following results. The current methods of calculating the compression index from the  log𝜎 curve and the coefficient of consolidation from the time-dependent settlement curve for each consolidation pressure proved that the final settlement amount will be consistent after a long time, but the actual settlement amount will always be smaller than the predicted settlement amount during the settlement progress stage. The consolidation factors estimated by the curve fitting with the condition that the secondary compression begins in the second half of the primary compression showed similar values to the consolidation factors estimated by the curve fitting for the primary compression only, and the settlement curves were in better agreement throughout the compression. It showed different values, showing low validity. It can be inferred that secondary compression acts from the point when a significant portion of the excess pore water pressure is dissipated, and the loading stress begins to have more influence on the skeletal structure of the soil. Analysis results show that secondary compression begins at the range of 91 % to 98 % on the average degree of primary consolidation.

• Journal of Ocean Engineering and Technology
• /
• v.25 no.1
• /
• pp.67-72
• /
• 2011

Offshore structures, such as a platform, a buoy, or a floating vessel, are exposed to several dynamic loads, and viscoelastic damping material is used to reduce the vibration of offshore structures. It is important to know the properties of viscoelastic materials because loss factor and Young's modulus of the viscoelastic damping material are dependent on frequency and temperature. In this study, an advanced technique for obtaining accurate loss factor and Young's modulus of the viscoelastic damping material is introduced based on a multi degree of freedom curve-fitting method and the RKU (Ross-Kerwin-Ungar) equations. The technique is based on a modified experimental procedure from ASTM E 756-04. Loss factor and Young's modulus of the viscoelastic damping material are measured for different temperatures by performing the test in a temperature-controlled vibration measurement room where temperature varies from 5 to 45 degrees Celsius.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.7
• /
• pp.913-917
• /
• 2013

During the restoration process of primary restorative transmission system, some over voltages may happen due to nonlinear interaction between unloaded transformers and transmission systems. These over voltages caused by harmonic resonance can be suppressed by inserting damping loads before energizing transformers. But it is very difficult to predict the occurrence possibility of harmonic resonance and complex simulation must be repeated to estimate the sufficient damping loads. This paper presents a damping loads prediction system to prevent harmonic resonance. Detailed analysis of the relationship between harmonic resonance and the amount of damping loads is discussed. The prediction system is developed using a curve fitting and a neural network based on this relationship. A curve fitting used a Gaussian function based on non-linear least square method and multi-layer back-propagation neural network is applied. The system is applied to primary restorative transmission lines in korean power system and the result showed satisfactory performance.

• Journal of Power System Engineering
• /
• v.16 no.1
• /
• pp.24-29
• /
• 2012

Recently, in the movie theater, the special chair is installed to maximize the viewing effect of movies. It is structured to convey a vibrational stimulus to a specially-designated parts of human body by attaching a vibration transducer to a existing theater chair. This paper describes the analysis of the vibration transfer characteristic of a foaming sponge seat for the design of the special chair. We could not apply the structural analysis S/W because it is difficult to obtain the mechanical properties and damping coefficients of the various type sponges. And then we computed the transfer functions by the global curve fitting program based on experimental modal analysis. The experimental response results comparatively coincide with those by the global curve fitting program. We also could obtain the natural frequencies, the modal damping coefficient ratio, the modal vectors and the whole transfer functions. Therefore we could analyze the dynamic characteristic for design of foaming sponge seat.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.1
• /
• pp.9-19
• /
• 2016

Accurate models of the characteristics of typical inverse-time overcurrent (OC) protective devices play an important role in the protective coordination schemes. This paper presents a novel approach to determine the OC protective device parameters. The approach is based on the Eigensystem Realization Algorithm which generates a state space model to fit the characteristics of OC protective devices. Instead of the conventional characteristic curves, the dynamic state space model gives a more exact fit of the OC protective device characteristics. This paper demonstrates the feasibility of decomposing the characteristic curve into smooth components and oscillation components. 19 characteristic curves from 13 typical and 6 non-typical OC protective devices are chosen for curve-fitting. The numbers of fitting components required are determined by the maximum absolute values of errors for the fitted equation. All fitted equations are replaced by a versatile equation for the characteristics of OC protective devices which represents the characteristic model of a novel flexible OC relay, which in turn may be applied to improve the OC coordination problems in the sub-transmission and distribution systems.

• The Journal of the Acoustical Society of Korea
• /
• v.19 no.3
• /
• pp.86-91
• /
• 2000

In this paper, we will discuss the characteristics of the magnitude and the phase of the piano sound in frequency domain by using the FFT(Fast Fourier Transform). The method deciding the parameters representing those sounds through the mathematical model is described. We used the curve fitting method for the modeling of the harmonic part of the sound including the fundamental frequency in order to minimize the errors between original sounds and modeled sounds. furthermore, we used the line segment approximation method for the modeling of the noise part around fundamental frequency. We also applied the same method for the phase model and could get the modeled sound to be similar to the original sound using the parameters. Therefore the high compression ratio comparing the modeled sound to the original sound is achieved.

• Journal of Sensor Science and Technology
• /
• v.9 no.6
• /
• pp.440-447
• /
• 2000

This paper describes a practical system to classify material temperature responses by composition of curve fitting and neuro-fuzzy inference. There are problems with a classification system which utilizes temperature responses. It requires too much time to approach the steady state of temperature response and it has to be filtered to remove the noise which occurs in experiments. Thus, this paper proposes a practical method using curve fitting only for transient state to remove the above problems of time and noise. Using the neuro-fuzzy system, the thermal conductivity of the material can be inferred on various ambient temperatures. So the material can be classified via its inferred thermal conductivity. To realize the system, we designed a contact sensor which has a similar structure with human finger, implemented a hardware system, and developed a classification software of curve fitting and neuro-fuzzy algorithm.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.11
• /
• pp.918-925
• /
• 2007

In this paper, different criteria fur determining hue change time in the hue detection based transient liquid crystals technique were compared. Results showed that methods utilizing threshold of intensity or saturation gave many missing points and quality of the calculated results were strongly depends on the value of threshold. Wider bandwidth in the hue bandwidth method showed better distribution of calculated hue change time, but induced ambiguity in the hue change time. In the time-hue curve fitting method, the distribution of evaluated hue change time was smooth and reasonable, and, by the nature of curve fitting, the noise effect on the hue was successfully considered in calculating of the hue change time. Compared to other methods, it is expected that the time-hue curve fitting method would provide better and accurate hue change time in the hue detection based transient liquid crystals technique.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.283-283
• /
• 2011

본 연구에서는 XRR 측정에 있어 박막두께 표준보급을 하기 위하여 표준물질을 이온빔 스퍼터링 증착법을 이용하여 제작하였다. 시편제작 시 공기 중 노출에 의해 산화가 되지 않는 산화물 박막과 산화물 기판을 선택하였다. 기판 및 타겟물질 등을 변화시키면서 제작된 시편의 특성을 살펴보았다. 사용된 타겟 물질로는 HfO2, Ta2O5, Cr2O3를 사용하였으며, 기판으로는 glass, sapphire, quartz, SiO2(1 ${\mu}m$-thermal oxidation)를 사용하였다. 산화물 타겟을 사용하여 증착 시 타겟 주위로 생기는 전하들의 charge build-up 되는 현상은 neutralizer를 사용함으로써 문제를 해결하였다. 제작된 시편은 XRR을 이용하여 측정하였고, XRR simulation과 curve fitting을 통하여 박막의 두께, 표면 및 계면의 거칠기, 밀도를 평가하였다. 기판으로 사용된 glass, quartz는 타겟 물질과 관계없이 표면 거칠기가 좋지 않아 XRR 반사율이 급격히 떨어지면서 측정되는 각도의 영역이 작아졌다. sapphire로 제작한 시편에서는 측정된 데이터와 simulation의 curve fitting이 양호하지 않았다. 이 문제는 현재 조사중에 있다. SiO2 기판으로 제작한 시편의 경우 타겟 물질과 관계없이 XRR curve fitting 결과가 양호 하였다. 그 중 Cr2O3의 결과가 다른 타겟 물질에 비해 x 2 값이 작았고 반사율 곡선에서의 거칠기와 진폭도 양호하였다. 위 연구결과로써 SiO2 기판을 사용한 Cr2O3 타겟 물질로 제작된 시편이 XRR 박막 두께 표준물질로써 적합한 것으로 판단된다.

• Current Optics and Photonics
• /
• v.7 no.6
• /
• pp.701-707
• /
• 2023

In laser imaging, accurate extraction of the laser's center is essential. Several methods exist to extract the laser's center in an image, such as the geometric mean, the parabolic curve fitting, and the Gaussian curve fitting, etc. The Gaussian curve fitting is the most suitable because it is based on the physical properties of the laser. The width of the Gaussian laser beam depends on the distance from the laser source to the target object. It is assumed in general that the distance remains constant at a laser spot resulting in a symmetric Gaussian model for the laser image. However, on a curved surface of the object, the distance is not constant; The laser beam is narrower on the side closer to the focal point of the laser light and wider on the side closer to the laser source, which causes the distribution of the laser beam to skew. This study presents a modified Gaussian model in the laser imaging to incorporate the slant angle of a curved object. The proposed method is verified with simulation and experiments.